Supplies Needed for a Tire Size Change
A plain guide to the supplies needed for a tire size change, from a jack and torque wrench to TPMS sensors, valve stems, a pressure gauge and balancing.
Contents
- Start with the hardware: tires and wheels
- Lifting and holding the vehicle safely
- Tire mounting supplies and shop equipment
- TPMS sensors and valve hardware
- Measuring and checking before the swap
- Finishing supplies: torque wrench and gauge
- Tire size change supply questions
- What do I need to change my own tires?
- What tools are needed for a tire size change?
- Are new valve stems and TPMS sensors part of the supplies?
- Can I mount a new tire size without a tire changer?
- How do I check a new tire size fits before buying supplies?
A tire size change needs both hardware and equipment. The hardware is the new tires in the size you chose, plus any valve stems and TPMS sensors that fit the new wheels. The equipment includes a jack and jack stands, wheel chocks, a lug wrench, a torque wrench, a pressure gauge and access to a tire changer and wheel balancer.
- Match the new tire size to the wheel width and to the clearance in the wheel wells before buying anything.
- A jack, jack stands and wheel chocks come first because the vehicle must be held safely before any wheel comes off.
- Mounting and balancing a tire needs a tire changer and a wheel balancer, which are shop equipment.
- A torque wrench and a pressure gauge finish the job and confirm the wheel is seated and the tire is inflated correctly.
- New valve stems and TPMS sensors belong on the supplies list whenever the wheels or the sensors change.
Start with the hardware: tires and wheels
The core supplies for a tire size change are the new tires in the chosen size and, when the bolt pattern or width changes, a matching set of wheels. The tire sidewall numbers give section width, aspect ratio, rim diameter, load index and speed rating, and the new size has to keep the overall diameter close to the original.
Wheel width must suit the new tire, because a tire squeezed onto a narrow rim or stretched over a wide one wears poorly and sits badly on the bead. Wheel fitment also covers bolt pattern, offset and hub bore, and a wheel that misses these points will not mount safely.
A wheel size comparison of the old and new figures shows what changes: a taller sidewall, a wider tread or a different rim. Write the numbers down before ordering, because a size that reads close on paper can still change speedometer readings and clearance at full steering lock.
Lifting and holding the vehicle safely
A floor jack and rated jack stands are the base of any tire change supplies list, with wheel chocks to stop the vehicle rolling. The jack lifts one corner, and the stands hold the vehicle while you work, so the jack alone never supports a raised car.
Chocks go against the wheels that stay on the ground, on the opposite side and diagonally from the corner being lifted. A lug wrench or breaker bar loosens the lug nuts before the vehicle rises, because a wheel in the air spins freely and resists the effort.
A trained specialist should handle lifting on a slope, on soft ground or under a heavy vehicle with no rated points. Set the stands on firm, level ground and lower the vehicle onto them slowly before you reach under a fender.
Tire mounting supplies and shop equipment
Tire mounting needs a tire changer to break the bead and seat the new tire on the rim, and this is shop equipment rather than a hand tool. Tire mounting supplies also include tire lube, a bead seater or a compressor with enough volume, and a valve stem tool for pulling a new stem into the rim.
New valve stems belong on the list whenever a tire comes off a rim, since the old rubber stem ages and can leak. Valve stem tools screw the stem into place and hold the core while the tire fills, and a core tool lets you replace a leaking core.
Hand tools can break a bead and levers can walk a tire onto a rim, but the risk of pinching the tube or damaging the bead is real. A tire changer is the safer route, and a shop with the machine can mount the set while you check the rest of the list.
TPMS sensors and valve hardware
TPMS sensors report tire pressure to the vehicle, and a size change that brings new wheels often means new sensors or a transfer of the old ones. Sensors fit specific wheels and vehicles, so the part number has to match the wheel and the vehicle's system.
A sensor service kit with a new nut, grommet or seal goes with each sensor that is reused, because the old seal can leak after a remount. Some vehicles learn a new sensor position by themselves, and others need a reset tool to register each wheel.
A tire pressure gauge confirms the sensor reading and checks the spare. Confirm the TPMS plan before the wheels are mounted, because fitting a sensor after the tire is seated means breaking the bead again.
Measuring and checking before the swap
Tire size measurement tools help you compare the old and new sizes before any hardware is bought. A tape measure checks the overall diameter of a mounted tire, and a tread depth gauge records wear so a used tire is not mixed with a new one on the same axle.
A wheel size comparison between the current and planned fitment shows the change in width, offset and diameter. Calculating the overall diameter from the sidewall numbers gives a figure you can check against the space in the wheel well and the clearance to suspension parts.
Turn the steering to full lock and look at the gap at the inner fender and the suspension arm before you commit to a wider or taller size. A fitment that touches at full lock or over a bump is a fitment that does not work, whatever the numbers say.
Finishing supplies: torque wrench and gauge
A torque wrench tightens the lug nuts to the vehicle maker's figure, and this step belongs in every tire size change checklist. Tightening by feel can leave a nut loose or overstretched, and a torque wrench set to the stated value removes the guesswork.
A tire pressure gauge sets the new tires to the pressure on the vehicle placard, which may differ from the pressure printed on the tire sidewall. The sidewall figure is a maximum, and the placard figure is the one the vehicle is designed around.
Recheck the lug torque after the first drive and again after a short distance, because a newly seated wheel can settle. Keep the gauge and the torque wrench in the vehicle so a pressure or torque check is a quick job.
Tire size change supply questions
What do I need to change my own tires?
Changing your own tires calls for a jack, rated jack stands, wheel chocks, a lug wrench, a torque wrench and a pressure gauge. Mounting the tire onto the rim needs a tire changer and a wheel balancer, and those are shop machines rather than hand tools.
What tools are needed for a tire size change?
A tire size change uses the same tools as a tire swap, plus measuring tools to compare the old and new dimensions. The list runs to a jack, jack stands, chocks, a lug wrench, a torque wrench, a pressure gauge, valve stem tools and access to a tire changer and balancer.
Are new valve stems and TPMS sensors part of the supplies?
Yes, new valve stems and TPMS sensors belong on the supplies list when a tire comes off the rim or new wheels go on. A fresh stem and a sensor service kit reduce the chance of a leak after the remount, and the sensor part must match the wheel and vehicle.
Can I mount a new tire size without a tire changer?
No, mounting a tire onto a rim safely needs a tire changer and a compressor with enough volume to seat the bead. Hand levers can do the job in some cases, but the risk of damaging the bead or pinching the tire is real, so a shop with the machine is the safer route.
How do I check a new tire size fits before buying supplies?
Compare the overall diameter of the old and new sizes using the sidewall numbers, then check wheel width, offset and bolt pattern. Measure the clearance in the wheel well at full steering lock before you order the tires, wheels and sensors.