Tire Sidewall Number Explanation

Decode the numbers on a tire sidewall: section width, aspect ratio, rim diameter, load index, speed rating, and the letters around them.

10 min read1 viewsTire Sidewall Number Explanation
— · 0 votes
Contents
  1. The three-part size code in order
  2. Section width: the first number
  3. Aspect ratio: the second number
  4. Rim diameter and the construction letter
  5. Load index and speed symbol after the size
  6. Letters and prefixes around the numbers
  7. Metric and inch sizes read differently
  8. Typical misreadings to check against
  9. A quick checklist for your own tire
  10. Tire sidewall number questions
  11. What do the numbers on a tire sidewall mean?
  12. What does the second number in tire size mean?
  13. Can I read the numbers on the side of a tire from a picture?
  14. How do I avoid a wrong interpretation of tire size numbers?
  15. What do the letters around the sidewall numbers mean?
  16. Does the DOT code give the tire size?

A tire sidewall number such as 205/55R16 tells you the tire's width, its sidewall height as a share of that width, and the wheel diameter it fits. Each figure sits in a fixed order, so the size code reads left to right. Letters and a second number group add the construction type, the load the tire carries, and the speed it is rated for.

  • The first number is the section width in millimeters, measured across the tire body.
  • The second number is the aspect ratio, the sidewall height as a percentage of the width.
  • The number after R or a similar letter is the rim diameter in inches.
  • The load index and speed symbol follow the size code and must match or exceed the vehicle's needs.
  • A DOT code on the sidewall carries a date of manufacture, not a size figure.

The three-part size code in order

A tire size code places three figures in a set order: width, aspect ratio, and rim diameter. The width comes first in millimeters, the aspect ratio second as a percentage, and the rim diameter last in inches. Learning that order is the whole of reading a size at a glance.

The code 205/55R16 reads as a 205 millimeter section width, a 55 percent aspect ratio, and a 16 inch rim diameter. A slash separates width from aspect ratio, and the R stands for radial construction. No number in this group is a height in millimeters or inches on its own.

Tire size digits stay in the same positions across metric sizes, which makes the code predictable. Metric sizing covers a passenger car or a light truck tire marked with a P or an LT prefix. Inch sizes on older or special tires use a different layout and are covered further down.

Code partExampleWhat it states
Section width205Tire width in millimeters
Aspect ratio55Sidewall height as a percentage of width
Construction letterRRadial build
Rim diameter16Wheel diameter in inches
Load index91Load the tire can carry
Speed symbolVTop rated speed

Section width: the first number

The section width is the tire's widest point across its body, given in millimeters. A 205 on the sidewall means the tire measures 205 millimeters across when mounted on its design rim. The section width sets how the tire sits on the road and how much clearance it needs.

Section width is not the tread width, and the two should not be swapped. The sidewall bulge adds to the width at the widest point, so a tire can be wider than its tread face suggests. Measuring your own tire gives a wider figure than the sidewall number when the rim is narrower than the design.

A wider section width fits a wider rim and changes the tire's footprint. Fitting a wider tire needs enough room in the wheel well and enough rim width to hold it. The vehicle maker's stated size is the reference point for any change.

Aspect ratio: the second number

The second number in tire size is the aspect ratio, and it states sidewall height as a percentage of section width. A 55 on a 205 millimeter tire gives a sidewall height of about 112 millimeters. The aspect ratio is a ratio rather than a fixed height, so the same number means different heights on different widths.

Sidewall height percentage works both ways, which is where readings go wrong. A lower aspect ratio gives a shorter, stiffer sidewall on the same width, while a higher one gives a taller, softer sidewall. The second number never gives the sidewall height in millimeters directly.

Aspect ratio affects the overall diameter of the tire when the rim stays the same. Changing from a 55 to a 50 series on the same width lowers the sidewall and the total diameter. That change alters speedometer readings and ground clearance, so compare overall diameter before choosing.

Rim diameter and the construction letter

The rim diameter is the figure after the construction letter, and it is stated in inches even when everything before it is metric. A 16 in a 205/55R16 code means the tire mounts on a 16 inch wheel. Rim diameter must match the wheel exactly, with no adjustment possible.

The construction letter sits between the aspect ratio and the rim diameter. An R means radial construction, where the cords run across the tire from bead to bead. A D for diagonal or a B for bias appears on some older designs, and a ZR marking on some sizes signals a higher speed capability.

Mixing metric and inch figures in one code confuses many readers, yet the format is deliberate. Width and sidewall share millimeters, while the rim uses inches because wheel sizes are sold that way. Read the letter and the last number as a pair before you look at rim width.

Load index and speed symbol after the size

Load index and speed rating sit after the size code as a number and a letter, such as 91V. The load index is a code for the maximum load one tire can carry at its rated pressure. The speed symbol is a letter for the top speed the tire is rated to sustain.

Load index and speed symbol confusion comes from treating them as size figures. Neither one changes the physical dimensions of the tire, and both must meet or exceed what the vehicle maker specifies. A lower load index than the vehicle requires reduces the safety margin under load.

Some sidewalls carry an extra load marking or an LT prefix for light truck service. These markings raise the load capacity for the same physical size, and they belong to the load side of the code. Always compare the full load and speed group when replacing a tire, not just the size digits.

Letters and prefixes around the numbers

Sidewall letters carry meaning that the numbers do not, and a prefix often comes first. A P prefix marks a P-metric tire built to a passenger car standard, while LT marks a light truck tire. These prefixes change the load standard applied to the same size code.

Other markings on the sidewall cover the tire type and its intended service. M+S indicates mud and snow capability, and a Three-Peak Mountain Snowflake symbol marks a tire tested for severe snow. Letters such as these sit apart from the size code and do not alter the dimensions.

The DOT code is a separate string near the bead area and holds a plant code and a date code. A DOT date code gives the week and year of manufacture in four digits, not a size figure. Reading the DOT code as a size is a frequent misreading, so keep it apart from the size group.

Metric and inch sizes read differently

Metric and inch sizes follow different layouts, so a single reading method does not cover both. A metric size uses width in millimeters, an aspect ratio, and a rim in inches. An inch size such as 31x10.50R15 gives overall diameter and width in inches with no aspect ratio.

The order of tire size code parts changes between the two systems, and that is the trap. In an inch size the overall diameter comes first, then the width, then the rim. Reading an inch size as if it were metric gives a width far larger than the real tire.

A flotation size for light trucks uses the inch format with a diameter in inches. Metric and inch sizes cannot be converted by moving a decimal point, because the inch format states overall diameter rather than sidewall percentage. Identify the format before you interpret any figure.

Typical misreadings to check against

Misreading tire size happens when a reader takes the wrong figure as the height or the width. The second number is the one most often mistaken for a sidewall height in millimeters. Checking each digit against its position prevents that error.

Another misreading treats the rim diameter as the overall tire diameter. A 16 inch rim on a 205/55 tire does not make the tire 16 inches tall across. The overall diameter adds the rim to twice the sidewall height, so the total is larger than the rim figure.

The load index and speed symbol are also misread as part of the size, and the DOT code as a date rather than a size. Before ordering a replacement, write the full sidewall string down and check each group against its meaning. A photo of the sidewall string helps confirm every character.

  • Read the width as millimeters, never as inches.
  • Treat the second number as a percentage, not a height.
  • Take the rim figure as inches across the wheel.
  • Keep the load index and speed symbol out of the size dimensions.
  • Separate the DOT date code from the size string.
  • Confirm the format is metric before reading the digits.

A quick checklist for your own tire

A tire sidewall number checklist starts with the size group and works outward along the string. Copy the full size code exactly as printed, including the construction letter. Then note the load index and speed symbol as a separate pair.

Next, identify the prefix and any letters around the size, such as P, LT, or M+S. Locate the DOT code and read its date digits apart from the size. Confirm the format is metric or inch before you interpret any number.

Compare the copied size with the vehicle maker's stated size for your model. Any change to width, aspect ratio, or rim diameter shifts the overall diameter and the fitment. Ask a tire technician to confirm clearance and load capacity when the size differs from the maker's figure.

Tire sidewall number questions

What do the numbers on a tire sidewall mean?

The numbers on a tire sidewall give the size in a fixed order, then the load and speed ratings. The first figure is the section width in millimeters and the second is the aspect ratio as a percentage. The figure after the construction letter is the rim diameter in inches.

What does the second number in tire size mean?

The second number is the aspect ratio, and it gives sidewall height as a percentage of the section width. A 55 on a 205 millimeter tire means a sidewall of about 112 millimeters. The figure is a percentage rather than a measurement in millimeters.

Can I read the numbers on the side of a tire from a picture?

A clear photo of the sidewall string lets you read the size, load index, and speed symbol. Check that the whole string is sharp and in frame, because one blurred digit changes the reading. A photo also helps a technician confirm the size before a replacement.

How do I avoid a wrong interpretation of tire size numbers?

Read each figure against its position: width, then aspect ratio, then rim diameter. Keep the load index and speed symbol separate from the size dimensions. Confirm whether the size is metric or inch before you start.

What do the letters around the sidewall numbers mean?

Letters such as P, LT, and R describe the tire's standard or construction, not its size. The R stands for radial construction and the P prefix marks a P-metric passenger tire. M+S and the snow symbol describe service conditions rather than dimensions.

Does the DOT code give the tire size?

No, the DOT code is not a size figure and carries a plant code and a date of manufacture. The four digits at its end state the week and year the tire was built. Tire size sits in the separate size group on the sidewall.

Latest articles