How to Change Tire Size on EZ LYNK
A step-by-step look at setting tire size on EZ LYNK, why tire diameter matters, and how speedometer calibration follows from an accurate tire size entry.
Contents
- What the tire size setting does
- Find the tire size before you start
- Prepare the vehicle and the device
- Steps to set tire size on EZ LYNK
- Enter diameter rather than guessing
- Check the result on the road
- Mistakes to avoid with tire size changes
- Questions about EZ LYNK tire size
- How do I change tire size on EZ LYNK?
- How do I set tire size on EZ LYNK if the field is greyed out?
- Does changing tire size on EZ LYNK fix the speedometer?
- Should I enter the tire size or the tire diameter?
- Why did my tire size setting revert after I saved it?
Changing tire size on EZ LYNK means entering the new tire size into the device so the vehicle software knows the tire diameter it is working with. The tire size setting feeds the speedometer calibration, so an accurate entry matters. The steps below cover the menu path in general terms, since the exact screens depend on your device model and the vehicle file loaded on it.
- The tire size setting exists so the vehicle software can correct speed and distance readings after a tire change.
- Tire diameter, not the nominal size label alone, is what the calibration reflects.
- The exact menu path on EZ LYNK depends on the device and the vehicle file loaded.
- Confirm the new size on the vehicle speedometer against a reference before trusting the reading.
- A file supplied by a tuner may lock or define the tire size, so check that first.
What the tire size setting does
The tire size setting tells the vehicle software how large the tires are, so it can correct the speedometer and odometer. A tire with a different diameter rolls a different distance per revolution, and the computer needs that number. EZ LYNK passes the value you enter through to the calibration.
Speedometer calibration depends on tire diameter, which comes from the numbers molded on the sidewall. A wider tire does not always mean a taller one, and a taller tire does not always mean a wider one. Reading the sidewall gives you the width, the aspect ratio and the wheel diameter the tire was built for.
A change in tire diameter shifts every reading that depends on wheel speed. A taller tire makes the vehicle travel farther per revolution than the software expects. The setting exists to remove that difference, so the displayed speed matches the real speed.
| Sidewall figure | What it tells you |
|---|---|
| Width | Section width of the tire in millimeters |
| Aspect ratio | Sidewall height as a share of the width |
| Wheel diameter | Rim size the tire mounts on |
| Load and speed index | Capacity and speed rating of the tire |
Find the tire size before you start
The tire size on EZ LYNK must match the tire that is physically on the vehicle. Read the sidewall of the new tires and write down the full size string. Check all four corners, since a used vehicle can carry mismatched tires.
The sidewall gives the width, the aspect ratio and the wheel diameter, as in a size such as 285/70R17. Those three figures describe the tire geometry, and the overall diameter follows from them. Confirm the wheel diameter matches the rims actually fitted to the vehicle.
Note any difference between the old and new size, because that difference is what the calibration corrects. A small change in diameter produces a small speed error, and a large change produces a large one. Write both sizes down before opening the device, so the entry is a copy rather than a guess.
Prepare the vehicle and the device
A correct tire size entry starts with a stable connection between the device and the vehicle. Park the vehicle safely, set the parking brake and switch the ignition to the position the device requires. Keep the device connected for the whole session so the write completes without interruption.
Open EZ LYNK and let it identify the vehicle before you change anything. The device reads the vehicle file, and that file may already define the tire size. Confirm which vehicle profile you are editing, especially if the device holds more than one.
A file written by a tuner can lock certain parameters, including the tire size setting. If the option is missing or greyed out, the file is the reason, not the device. Contact the tuner who supplied the file rather than forcing a change.
Steps to set tire size on EZ LYNK
The tire size setting on EZ LYNK sits inside the vehicle configuration menu of the app. The exact labels differ between device models and software versions, so read each screen rather than following a fixed path. The sequence below describes the job in general terms.
Work through the menu until you reach the tire size field, then enter the size that matches the tires on the vehicle. Save the change and let the device write it to the vehicle. Wait for the confirmation screen before you disconnect anything.
After the write completes, cycle the ignition as the app instructs and reconnect. Reopen the tire size screen to confirm the value was stored. A stored value that reverts points to a locked file or an interrupted write.
- Park safely and set the parking brake.
- Connect the device and let it identify the vehicle.
- Open the vehicle configuration menu.
- Locate the tire size field.
- Enter the size from the tire sidewall.
- Save the change and wait for confirmation.
- Cycle the ignition and recheck the stored value.
Enter diameter rather than guessing
Some tire size screens accept a size string, while others ask for a diameter figure. Tire diameter is the overall height of the inflated tire from the ground to the top. If the screen asks for a diameter, calculate it from the sidewall figures instead of estimating by eye.
The calculation starts with the width in millimeters and the aspect ratio. Sidewall height equals the width multiplied by the aspect ratio, divided by one hundred. Overall diameter adds two sidewall heights to the wheel diameter, converted to the same unit.
A published tire specification from the manufacturer gives a measured diameter that can differ from the calculated figure. Use the manufacturer figure when you have it, and use the calculation when you do not. Enter the number in the unit the screen expects, since a unit mix-up produces a large error.
Check the result on the road
Speedometer calibration is only proven once the vehicle is driven and the reading is compared. Drive a steady speed on a safe road and compare the displayed speed with a trusted reference. A small difference can remain even after a correct entry, since the calibration has finite resolution.
An uncorrected change shows up as a speed reading that drifts further from reality as speed rises. The direction of the error tells you whether the entered diameter is too large or too small. Recheck the tire size entry before changing anything else.
Recheck the setting after any tire swap, rotation onto a different size or wheel change. The stored value describes the tires fitted at the time of the write, not the tires fitted later. Keep a note of the size string used, so the next change starts from a known value.
Mistakes to avoid with tire size changes
The largest error is entering the size you intended to buy rather than the size fitted to the vehicle. The calibration must describe the tires in contact with the road. Verify the sidewall again if there is any doubt.
A second error is disconnecting the device mid-write, which can leave the configuration incomplete. Wait for the app to confirm the write before you touch the cable. Repeat the write if the app reports a failure, and stop if failures repeat.
A third error is assuming the device ignores a locked parameter. A tuner file can override or forbid a tire size change, and no menu action will fix that. Work with the tuner who supplied the file when the setting will not stick.
Questions about EZ LYNK tire size
How do I change tire size on EZ LYNK?
Open the vehicle configuration menu in the EZ LYNK app, find the tire size field and enter the size from the tire sidewall. Save the change, let the device write it to the vehicle and confirm the stored value afterward. The exact menu labels vary with the device model and software version.
How do I set tire size on EZ LYNK if the field is greyed out?
A greyed-out tire size field on EZ LYNK points to a locked or custom vehicle file. The file defines which parameters the app may change, and the tire size may not be among them. Contact the tuner who supplied the file to have the setting unlocked or adjusted.
Does changing tire size on EZ LYNK fix the speedometer?
Yes, a correct tire size entry on EZ LYNK lets the vehicle software recalibrate the speedometer for the new tire diameter. The reading improves because the software now knows the distance each wheel revolution covers. Small residual differences can remain because the calibration has finite resolution.
Should I enter the tire size or the tire diameter?
Enter whichever value the EZ LYNK screen asks for, since some screens take a size string and others take a diameter. Tire diameter can be calculated from the width, aspect ratio and wheel diameter on the sidewall. Use the tire manufacturer published diameter when it is available, because measured figures differ from calculated ones.
Why did my tire size setting revert after I saved it?
A tire size setting that reverts on EZ LYNK usually means the write did not complete or the vehicle file restored its own value. An interrupted connection or a locked parameter can cause the same result. Reconnect, repeat the write and check the stored value before driving.