Tire Loading Information Sticker: Load Capacity and Pressure Entries
Read the tire loading information sticker on your vehicle: what the seating capacity, cargo weight, load capacity and cold inflation pressure entries mean.
Contents
- What the tire loading information sticker contains
- Seating capacity and cargo weight on one payload figure
- Load capacity versus sidewall maximum
- Reading the load index and load range
- Cold tire inflation pressure on the placard
- How to check your load and pressure
- When the sticker and the tires disagree
- Questions about the tire loading sticker
- Where is the tire loading information sticker located?
- Is the sticker load capacity the same as the tire sidewall maximum?
- Should I inflate my tires to the pressure on the sticker or the sidewall?
- Does seating capacity include the driver?
- What do I do if the sticker is missing or unreadable?
The tire loading information sticker lists how much weight your vehicle can carry and the cold tire inflation pressure needed for that load. It shows the seating capacity, the cargo weight allowance, the maximum load for the vehicle and the pressure for the original tires. The sticker states limits for the vehicle as built, not the maximum printed on the tire sidewall.
- The sticker gives the vehicle's load limit and the cold inflation pressure for its original tires.
- Seating capacity and cargo weight share one payload figure, so passengers reduce what you can load.
- The load capacity on the sticker can be lower than the maximum load rating molded on the tire sidewall.
- Set pressure on cold tires and add pressure only as the sticker or the vehicle maker directs.
What the tire loading information sticker contains
The tire loading information sticker is a placard fixed to the vehicle, often on the driver door jamb or the fuel filler door. It lists the number of seating positions, the combined weight of occupants and cargo the vehicle can carry, and the tire sizes fitted at the factory. The placard also gives the cold tire inflation pressure for the front and rear axles.
A separate vehicle certification label carries the gross vehicle weight rating and the gross axle weight ratings. The tire and loading information label works with that certification label, since one sets the tire pressure and the other sets the overall weight limits. Reading both together tells you how the load capacity of the vehicle is split between the axles.
The sticker describes the vehicle as it left the factory with its original tire size. If someone fits a different size or a different load range, the sticker no longer matches the tires on the wheels. A trained tire technician can confirm which pressure and load figures apply to a changed setup.
Seating capacity and cargo weight on one payload figure
Seating capacity and cargo weight come out of the same payload number on the sticker. The label gives the maximum weight of occupants and cargo together, so every passenger takes weight away from what remains for luggage. The figure does not change when seats are folded or left empty.
To use the payload figure, add the weight of the people riding in the vehicle to the weight of what you load. That total must stay at or below the combined limit printed on the sticker. Heavy items placed behind the rear axle add load to the rear tires and change how the vehicle handles.
The payload limit assumes the vehicle is otherwise standard, with no added accessories or tow equipment. Extra parts bolted on after delivery reduce the weight left for people and cargo. If you carry a heavy load on a regular basis, a technician can check the axle loads against the ratings.
Load capacity versus sidewall maximum
Load capacity versus sidewall maximum is the comparison that confuses many drivers. The tire sidewall carries a maximum load rating, which is the most weight one tire can support when inflated to its rated pressure. The sticker carries a vehicle load figure that may sit well below the sum of four sidewall ratings.
The vehicle maker sets the sticker figure to match the suspension, brakes and axle ratings of the car. Fitting tires with a higher sidewall maximum does not raise the payload printed on the placard. Tires with a lower maximum than the sticker requires are not suitable for the vehicle.
When tires are replaced, the new set must meet or exceed the load capacity the sticker calls for at the stated pressure. A load index number on the sidewall translates to a load in weight, and the load range tells you the ply construction and pressure capability. A technician compares these figures before mounting a different tire.
Reading the load index and load range
The load index is a code on the tire sidewall that corresponds to a maximum load for that single tire. A higher index number points to a tire built to carry more weight at its rated pressure. The index works with the sticker figure, which sets what the vehicle actually needs.
Load range uses letters to describe the strength and inflation limits of a tire's construction. A higher load range tire can hold more pressure and carry more load than a lower one of the same size. The load range does not by itself raise the payload of the vehicle it is bolted to.
Matching load index and load range to the sticker keeps the vehicle within its designed limits. Going below the required index leaves the tires underrated for a fully loaded car. Going above it adds reserve capacity but does not change the placard.
Cold tire inflation pressure on the placard
Cold tire inflation pressure is the pressure measured before the tires have been driven and warmed up. The sticker gives this cold figure because heat raises pressure, and a hot reading overstates what the tire holds when parked. Check pressure when the vehicle has sat for a while or has covered little distance.
The pressure on the placard is set for the load the vehicle is designed to carry, not for the maximum pressure molded on the sidewall. The sidewall maximum pressure is a ceiling for the tire, and the sticker figure sits at or below it. Inflating to the sidewall maximum on a light load gives a harsh ride and uneven tread wear.
Front and rear pressures can differ on the same vehicle, so read each axle line on the sticker. Some placards list a higher pressure for a fully loaded condition. Follow the table or note on the label rather than adding pressure by guesswork.
How to check your load and pressure
Checking load and pressure starts with reading the sticker on your own vehicle, since every model differs. Note the seating capacity, the combined occupant and cargo limit, and the front and rear cold pressures. Then compare those figures with the tire size and load index on the wheels.
Weigh the people and cargo you plan to carry, or estimate them, and keep the total under the payload figure. Set each tire to the cold pressure printed for its axle, using a gauge you trust. Recheck pressure before a long trip with a full load.
If the tires on the vehicle differ from the sticker size, or the placard is missing, do not guess. A trained tire technician can match a replacement set to the vehicle and confirm the pressure to use.
When the sticker and the tires disagree
The sticker and the tires can disagree after a size change, a lift kit or a set of aftermarket wheels. The placard still describes the factory combination, so its pressure may not suit the tires now fitted. Load capacity may also fall short if the new tires carry a lower load index.
A disagreement is not a reason to ignore either figure. The vehicle still needs enough tire load capacity for its weight, and the tires still need a pressure suited to the load they carry. A technician works out a pressure that respects both the tire limits and the vehicle ratings.
Keep the original placard in place even when the tires change, because it records the vehicle's designed limits. Note any approved change separately for your own records. Never remove or cover the label to hide a mismatch.
Questions about the tire loading sticker
Where is the tire loading information sticker located?
The tire loading information sticker sits on the driver door jamb on many vehicles, and some makers place it on the fuel filler door or inside the glovebox. The exact spot depends on the model and the market it was built for. Look for a label listing seating capacity, cargo weight and cold tire pressures.
Is the sticker load capacity the same as the tire sidewall maximum?
No, the sticker load capacity is a vehicle figure and the sidewall maximum is a tire figure. The sticker sets what the car is designed to carry, while the sidewall states the most one tire can support at its rated pressure. The sticker figure can be lower than the sum of the four sidewall ratings.
Should I inflate my tires to the pressure on the sticker or the sidewall?
Follow the cold tire inflation pressure on the sticker for normal driving. The sidewall maximum is a ceiling for the tire, not a target for everyday use. A different tire size or load range may call for a technician to confirm the right pressure.
Does seating capacity include the driver?
Yes, seating capacity counts the driver as one of the occupants on the tire loading information sticker. The driver's weight comes out of the same combined occupant and cargo limit as every passenger. Leave room in the payload figure for the driver before loading luggage.
What do I do if the sticker is missing or unreadable?
A missing or unreadable sticker leaves you without the vehicle's stated load and pressure figures. A dealer or a trained tire technician can supply the correct values for the vehicle as built. Do not substitute the sidewall maximum pressure as a replacement for the placard.