Spare Tire Cover Size Calculator
Work out the right spare tire cover size from the sidewall markings, calculate overall diameter step by step, and check width and fit before buying.
Contents
- How a spare tire cover calculator works
- Reading the size from sidewall markings
- Formula for cover diameter from tire size
- Worked examples for several tire sizes
- Measuring a spare tire with a tape
- Soft, hard and hybrid covers fit differently
- Camera openings and carrier clearance
- Checking the fit once the cover is on
- Spare tire cover sizing questions
- How do I calculate the size of a spare tire cover?
- Should I measure the spare tire inflated or deflated?
- Does tread wear change the spare tire cover size?
- Can I reuse my old spare tire cover on a new tire?
- Are spare tire covers sized by tire size or by diameter?
A spare tire cover size calculator converts the sidewall size into the tire's overall diameter. That diameter, together with the tire's width, tells you which cover will fit your spare. You can check the result by hand with a short formula and a tape measure.
- Read the tire size on the sidewall, such as 265/70R17, before looking at covers.
- Overall diameter equals rim diameter plus two sidewall heights, converted to inches.
- Match your result to the cover's stated diameter range, not to the wheel size.
- Measure the inflated spare with a tape to confirm the calculated figure.
- Check width and carrier clearance as well as diameter before choosing a cover.
How a spare tire cover calculator works
A spare tire cover calculator takes a tire size and returns the tire's overall diameter in inches. Cover makers list their products by diameter range or by tire size. The calculated diameter lets you compare your spare against those listings directly.
Tire overall diameter is the distance across the inflated, unloaded tire through the center of the wheel. The figure includes the wheel itself plus the sidewall height above and below it. A cover must span that full circle to wrap the tread edge snugly.
Wheel diameter alone is not enough to pick a cover. Two tires on the same 17-inch wheel can differ by several inches in height. The sidewall height, set by width and aspect ratio, makes that difference.
Reading the size from sidewall markings
Sidewall markings give every number a cover calculation needs in one short code. In a size like 265/70R17, 265 is the section width in millimeters. Section width means the widest point of the inflated tire, sidewall to sidewall. The 70 is the aspect ratio, and 17 is the rim diameter in inches.
The aspect ratio tells you how tall the sidewall is compared with the width. Multiply the width by the aspect ratio and divide by 100 to get sidewall height. The letter R only marks radial construction and does not affect the math.
Some tire sizes carry a prefix such as P or LT, meaning passenger or light truck. The characters after the size, such as 112T, are the load index and speed rating. Neither the prefix nor these service codes change the dimensions used for a cover.
Formula for cover diameter from tire size
The cover diameter from tire size comes from one formula: rim diameter plus two sidewall heights. Sidewall height is found in millimeters, while rim diameter is given in inches. Convert the sidewall figure to inches by dividing by 25.4 before adding.
In one line, diameter equals rim size plus twice the width times aspect ratio over 2540. The number 2540 combines dividing by 100 for the ratio and by 25.4 for inches. Any phone calculator handles these steps without a dedicated tool.
The calculated diameter is nominal, meaning the design size of a new, properly inflated tire. Real tires vary slightly with tread depth, rim width and inflation pressure. Treat the result as a target and choose a cover whose range includes it with some margin.
- Multiply the section width in millimeters by the aspect ratio, then divide by 100.
- Divide that sidewall height by 25.4 to convert it to inches.
- Double the sidewall height to count the top and bottom sidewalls.
- Add the rim diameter in inches to get the overall diameter.
- Compare the result with the cover's listed diameter range.
Worked examples for several tire sizes
Worked examples of the formula show how strongly tire size changes the cover you need. A 225/65R17 spare has a sidewall of about 5.8 inches, for an overall diameter near 28.5 inches. A 265/70R17 on the same wheel size reaches about 31.6 inches.
The 265/70R17 math runs like this: 265 times 70 divided by 100 gives 185.5 millimeters. Dividing by 25.4 gives about 7.3 inches per sidewall. Two sidewalls make 14.6 inches, and adding the 17-inch rim gives 31.6 inches.
Flotation sizes, written like 33x12.50R15, state the overall diameter in inches as the first number. The second number is the section width in inches, and the last is the rim diameter. A 33x12.50R15 spare needs a cover rated for about 33 inches with room for a wide tread.
| Tire size | Sidewall height (in) | Overall diameter (in) | Section width (in) |
|---|---|---|---|
| 225/65R17 | 5.8 | 28.5 | 8.9 |
| 245/75R16 | 7.2 | 30.5 | 9.6 |
| 265/70R17 | 7.3 | 31.6 | 10.4 |
| 285/70R17 | 7.9 | 32.7 | 11.2 |
| 33x12.50R15 | 9.0 | 33.0 | 12.5 |
Measuring a spare tire with a tape
Spare tire measurement with a tape confirms the calculation and catches worn or mismatched tires. Measure the inflated spare straight across its face, passing through the center of the hub. Hook the tape on the outer tread at one side and read it at the opposite tread.
Measuring the spare in place works for a tire mounted on a rear door or swing-out carrier. Keep the tape straight, since a sagging tape reads longer than the true diameter. Repeat the measurement at a second angle and use the larger figure.
Width is the second measurement, taken at the widest point between the two sidewalls. Some covers list a depth or maximum width, which should equal or exceed that figure. Note both numbers before comparing them with any cover listing.
Soft, hard and hybrid covers fit differently
Soft spare tire covers are made of vinyl or fabric with an elastic or drawstring edge. Each soft cover is sold for a stated range of diameters, which varies by maker. A tire at the top of the range fits tightly, while one at the bottom may sag.
Hard spare tire covers use a rigid plastic or metal shell around the tread. A hard cover suits a narrow size range and must match the tire closely. Some hard covers attach with a backing plate fixed to the wheel studs or carrier.
Hybrid spare tire covers combine a rigid face with a flexible band around the tread. The band absorbs small size differences, while the face keeps a flat, finished look. Check the listed diameter range for a hybrid cover just as you would for a soft one.
Camera openings and carrier clearance
A rear camera mounted in the spare tire carrier needs a cover with a matching opening. Covers made with a camera hole place it at the top or center, depending on the design. Check where your camera sits before choosing between these layouts.
Carrier clearance is the space between a door-mounted spare and nearby body parts. A bulky cover may touch the bumper, a third brake light or the door frame. Measure the gap around the tire before choosing a thick or rigid cover.
An oversized spare on a factory carrier can strain the hinge and change the clearance a cover needs. Fitting a larger spare than the vehicle maker specifies is a job for a qualified specialist. Size the cover only after the spare and carrier combination is confirmed.
Checking the fit once the cover is on
A cover fit calculation is confirmed only when the cover sits evenly on the mounted spare. The edge should wrap the tread all the way around without gaps or bunching. A loose soft cover can flap at speed and wear through against the tread.
An undersized spare tire cover shows stretched seams and an edge that refuses to seat. Forcing an undersized cover can tear the material or crack a rigid shell. Moving up to the next size range avoids that damage.
An oversized spare tire cover leaves slack around the tread that catches wind and road dirt. A drawstring edge on some soft covers can be tightened to take up small amounts of slack. Recheck the fit after a few drives, since vinyl can relax or shift in sun and cold.
Spare tire cover sizing questions
How do I calculate the size of a spare tire cover?
You size a spare tire cover by calculating the tire's overall diameter from the sidewall size. Multiply width by aspect ratio, divide by 2540, double it and add the rim diameter in inches. Match that figure to the diameter range the cover maker states.
Should I measure the spare tire inflated or deflated?
Measure a spare tire inflated to the pressure listed for it by the vehicle or tire maker. A soft or flat tire reads smaller across its face. That smaller reading can point you to a cover that ends up too tight.
Does tread wear change the spare tire cover size?
Only slightly, since tread wear lowers the overall diameter of a spare tire by a small amount. The reduction equals the lost tread depth counted twice, once at the top and once at the bottom. A cover chosen for the new-tire diameter can still fit a worn spare if its range has some margin.
Can I reuse my old spare tire cover on a new tire?
Yes, an old spare tire cover fits a new spare whose diameter falls inside its range. Run both sidewall sizes through the diameter formula to compare them. A camera opening or mounting plate must also line up with the new setup.
Are spare tire covers sized by tire size or by diameter?
Spare tire covers are sized both ways, depending on the maker. Some list the tire sizes they fit, while others give a diameter range in inches. Converting your tire size to diameter lets you compare either type of listing.