How to Measure Tire Sidewall Height and Width
Learn how to measure tire sidewall height and width two ways: read the sidewall size code or use a tape measure and caliper on a mounted tire.
Contents
- Read the size code before you measure
- Calculate sidewall height from the numbers
- Measure tire width with a tape measure
- Measure tire sidewall height with a caliper
- Check tire height and width with the tire mounted
- Account for load, pressure and wear
- Match your measurements to the wheel
- Tire Sidewall Measurement Questions
- How do I find tire height from the sidewall numbers?
- How do I measure tire width from the sidewall?
- Can I measure sidewall height with a caliper?
- How is the profile of a tire measured?
- How do I measure tire height in inches?
- How do I measure tire width sidewall to sidewall?
You measure tire sidewall height two ways: read the size code on the sidewall or measure it directly on a mounted, inflated tire. Tire width comes from the same code or from a tape measure stretched across the tire. The numbers on the sidewall give section width and aspect ratio, and those two figures set the sidewall height.
- The first number in a size code such as 225/45R17 is section width in millimeters.
- The second number is the aspect ratio, a percentage of section width that gives sidewall height.
- A tape measure across the tread or sidewall gives an overall width you can compare with the code.
- Sidewall height in inches equals section width times aspect ratio, then divided by 2540.
- Hand tools read close to the marked size, but an inflated tire flexes and never matches it exactly.
Read the size code before you measure
The sidewall size code holds the width and height figures you would otherwise measure with tools. A marking like 225/45R17 states section width in millimeters first and aspect ratio second. The R shows radial construction, and the last figure is the wheel diameter in inches. Reading the code first tells you what the physical measurements should come close to.
Section width is the width of the tire cross section, taken at the widest point of the inflated sidewall. The width figure in the code is not the tread width, so a tape across the tread gives a smaller number. Aspect ratio is the sidewall height written as a percentage of section width, not a fixed length. A 45 aspect ratio means the sidewall stands at 45 percent of the section width.
The sidewall code describes a new tire at its rated inflation, so a worn or deflated tire reads differently. Use the code as the reference point, then confirm it with a tape measure when fitment matters. Measuring the tire also catches a mismatch between the code and what is actually mounted.
Calculate sidewall height from the numbers
Sidewall height from the sidewall numbers is a short calculation that needs no tools. Multiply the section width by the aspect ratio, then divide by one hundred. For a 225/45 tire, 225 times 45 equals 10125, and dividing by 100 gives about 101 millimeters of sidewall. This method gives the nominal height the manufacturer designed into the tire.
To get the sidewall height measurement in inches, divide the millimeter result by 25.4. The same 101 millimeter sidewall comes out near 4 inches. To find overall tire height in inches, double the sidewall figure and add the wheel diameter. That total is the tire height you compare against a replacement size.
The aspect ratio check confirms the size code and your arithmetic agree. A smaller aspect ratio on the same width gives a shorter sidewall, and a taller one gives more sidewall. Sidewall height changes ride feel and speedometer accuracy, so confirm the figures before you buy.
Measure tire width with a tape measure
Tire width measurement with a tape measure gives the physical cross-section width of the mounted tire. Park on level ground and inflate the tire to its rated pressure, because pressure changes the shape. Stretch the tape from one sidewall to the other at the widest point, level with the axle. Keep the tape straight and parallel to the ground so the reading is not skewed.
A sidewall-to-sidewall measurement includes the sidewall bulge, the outward curve where the tire meets the rim. Overall tire width across the tread and shoulders reads narrower than the section width. Decide which width you need before you start, since the tape can be placed in different spots. Section width is the figure that matches the size code.
Record the reading to the nearest millimeter for a clean comparison. Repeat the measurement at a second height around the tire and average the two results. Measuring a mounted tire is a two-person job when the tape has to span a wide tire.
Measure tire sidewall height with a caliper
A caliper measurement reads sidewall height directly when the tire is off the vehicle. Use a caliper with deep jaws, or a dedicated tire gauge that reaches from the rim edge to the tread. Place one jaw against the rim flange and the other against the outermost tread surface. Read the depth on the scale and note the figure in millimeters or inches.
The tape measure method works on a mounted tire but the caliper method is more precise on a loose one. A caliper reads one point of the sidewall, so take several readings around the tire. Sidewall height varies slightly with load and inflation, so a small spread between readings is expected. Compare the average against the figure you calculated from the size code.
Do not force a caliper into a mounted, inflated tire, because the jaws can slip or damage the bead. A trained technician should handle tire dismounting and remounting safely. Never work under a vehicle supported only by a jack when you measure a mounted tire.
Check tire height and width with the tire mounted
How to check tire height on an inflated tire comes down to one total: rim diameter plus two sidewalls. Stretch a tape from the ground to the top of the tire and read the overall diameter. Divide that figure by two, then subtract half the wheel diameter to estimate sidewall height. The result should sit close to the calculated value if the size code is accurate.
Overall tire height depends on the section width, the aspect ratio, and the wheel diameter together. Changing any one of those figures changes the total height and the fitment. Compare the measured height against the original size when you plan a replacement. A tire that is taller or shorter than the original affects clearance and speedometer readings.
Measuring with the tire mounted is the practical route for a vehicle already on the ground. Clean the sidewall first and hold the tape tight so it does not sag. Note the pressure before you measure, then check it again afterward.
Account for load, pressure and wear
Sidewall height measurement shifts with tire pressure, vehicle load, and tread wear. A soft tire bulges more and reads wider at the lower sidewall. A fully inflated tire stands taller and narrower than one carrying the same load at low pressure. Measure at the rated inflation shown on the tire or the vehicle placard.
Tread wear shortens the overall height, which changes the sidewall figure you get from a ground-to-top tape. A worn tire measures shorter than a new one of the same size. Width readings move less with wear, but the sidewall bulge still depends on pressure. State the conditions whenever you compare two measurements.
Temperature changes pressure, and hot tires read slightly different from cold ones. Take readings on a cool tire when precision matters. Keep a written record of the size code, pressure, and measured figures so future comparisons are honest.
Match your measurements to the wheel
A tire width measurement must match the rim width range for that tire size. Measure rim width between the inner faces of the flanges, then compare it to the tire manufacturer's approved range. A tire squeezed onto a narrow rim bulges outward and reads wider than its section width. A tire stretched over a wide rim sits flatter and may expose the rim edge to damage.
Sidewall height also affects fitment, since a taller tire changes clearance to the fender and suspension. Check the diameter against the original size before you commit to a new set. Tire width and sidewall height work as a pair, so decide both together. A sizing chart for the specific tire covers approved rim widths.
Mounting and balancing a tire needs a trained specialist with the right equipment. Ask the specialist to confirm your calculated figures against the tire data before mounting. Final clearance checks belong on the vehicle, not on the bench.
Tire Sidewall Measurement Questions
How do I find tire height from the sidewall numbers?
Tire height comes from the size code by multiplying section width by aspect ratio and dividing by one hundred, then doubling the result and adding wheel diameter. A 225/45R17 tire has a sidewall near 101 millimeters, so the total height is about 25 inches. Convert the sidewall figure to inches by dividing by 25.4.
How do I measure tire width from the sidewall?
Tire width from the sidewall is the first number in the size code, given in millimeters as the section width. To confirm it physically, stretch a tape from one sidewall to the other at the widest point of an inflated tire. The measurement includes the sidewall bulge and should read close to the code.
Can I measure sidewall height with a caliper?
A caliper measures sidewall height well on a tire that is off the vehicle. Deep jaws reach from the rim edge to the tread surface and give a direct reading. Do not force a caliper into an inflated mounted tire, and let a trained technician handle dismounting.
How is the profile of a tire measured?
Tire profile measurement starts with the aspect ratio, the second number in the size code, which sets sidewall height as a percentage of section width. Measure the sidewall directly with a caliper on a loose tire or a tape from rim to tread. Compare the direct reading against the calculated figure for a check.
How do I measure tire height in inches?
Measure overall tire height in inches with a tape from the ground to the top of the mounted tire, then convert millimeters by dividing by 25.4. To calculate it instead, multiply section width by aspect ratio, divide by 2540, and add the wheel diameter. The calculated and measured figures should agree within a small margin.
How do I measure tire width sidewall to sidewall?
Sidewall-to-sidewall measurement uses a tape across the widest point of a mounted, inflated tire, held level with the axle. Two people keep the tape straight and tight for an accurate reading. Repeat the measurement at a second point and average the results.