Dirt Bike Tire Size Comparison: Comparing Sizes and Dimensions
Learn how to compare dirt bike tire sizes by reading the sidewall numbers and calculating overall diameter, section width and rim diameter.
Contents
- How dirt bike tire sizes are written
- Calculating section height and overall diameter
- What the size difference means in practice
- Reading the sidewall beyond the size
- Comparing front and rear tire sizes
- Checking fitment before you change size
- Avoiding errors in a size comparison
- Dirt bike tire size questions
- How do I compare two dirt bike tire sizes?
- What do the sidewall numbers mean on a dirt bike tire?
- How is overall diameter calculated for a dirt bike tire?
- Can I fit a wider tire on the same rim?
- Does a larger overall diameter change how the bike rides?
A dirt bike tire size comparison starts with the three numbers on the sidewall, read in the order of section width, aspect ratio and rim diameter. From those figures you can work out the overall diameter and see how two tires differ. Comparing sizes this way tells you how a tire sits on the rim and how much room it takes up.
- Read a dirt bike tire size as section width, then aspect ratio, then rim diameter.
- Section width is a nominal figure that depends on the rim width the tire is mounted on.
- Overall diameter is section height times two plus rim diameter.
- Two tires with the same rim diameter can still differ in width and height.
- Check clearance and rim fit before changing a tire size.
How dirt bike tire sizes are written
A dirt bike tire size comparison begins with the markings molded into the sidewall. A size such as 110/90-19 gives the section width first, the aspect ratio second and the rim diameter last. The hyphen or the letter after the aspect ratio marks the rim diameter, which is given in inches.
The first number is the section width in millimeters, or a letter code on older sizing systems. The second number is the aspect ratio, which is the sidewall height as a percentage of the section width. The final number is the rim diameter in inches that the tire is built to fit.
Sidewall numbers describe a nominal size, not a measured one. A tire only reaches its stated section width when it is mounted on the rim width the maker specifies. Reading all three numbers together is what makes a tire size comparison meaningful.
Calculating section height and overall diameter
Overall diameter is the figure that decides how tall a dirt bike tire stands on the bike. The calculation starts with the section width and the aspect ratio. Multiply the section width by the aspect ratio divided by one hundred to get the section height.
Double the section height, because the tire has a sidewall above and below the rim, then add the rim diameter. Convert the rim diameter from inches to millimeters if you want one unit throughout. The result is the nominal overall diameter of the mounted tire.
A worked example shows the method. For a 110/90-19 tire, the section height is 99 millimeters, so the doubled sidewall adds 198 millimeters. A 19 inch rim is about 483 millimeters, which gives a nominal overall diameter of roughly 681 millimeters.
| Size | Section width | Section height | Rim diameter | Nominal overall diameter |
|---|---|---|---|---|
| 110/90-19 | 110 mm | 99 mm | 19 in | about 681 mm |
| 120/80-19 | 120 mm | 96 mm | 19 in | about 675 mm |
| 100/100-18 | 100 mm | 100 mm | 18 in | about 657 mm |
| 120/100-18 | 120 mm | 120 mm | 18 in | about 697 mm |
What the size difference means in practice
A wider section width changes how the tire sits on the rim and how much space it needs. The same rim diameter with a larger first number gives a broader tire, which can change steering feel and the gap to the swingarm. Rim width must suit the tire, or the sidewall profile changes.
The aspect ratio governs sidewall height for a given width. A lower aspect ratio gives a shorter sidewall and a smaller overall diameter on the same rim. A higher aspect ratio adds sidewall height and raises overall diameter, which affects gearing and ground clearance.
A different rim diameter shifts the whole tire up or down. An 18 inch and a 19 inch rim cannot take the same tire, whatever the other numbers say. Compare rim diameter first, then width and height, when you put two sizes side by side.
Reading the sidewall beyond the size
The sidewall carries more than the size string, and those extra markings belong in a full comparison. A load and speed index shows the load the tire is rated to carry at a stated speed. A direction arrow or a rotation marking shows the intended rolling direction.
Some dirt bike tires are marked for front or rear fitment, and the tread pattern is built around that position. Tube type and tubeless markings tell you which setup the tire expects. Rim width recommendations from the maker sit alongside the size and matter for profile.
The date of manufacture appears as a code on the sidewall, and it does not change the size. Check every marking against the bike maker's specification before fitting. A trained technician can confirm whether a size and marking set suits your rim and frame.
Comparing front and rear tire sizes
Front and rear dirt bike tires are compared as separate pairs of figures, not as one size. The front tire is narrower and carries a different tread and profile from the rear. Each position has its own rim diameter target on a given bike.
Rear tires carry the drive load, so their section width and aspect ratio are read with gearing in mind. A larger overall diameter at the rear changes the effective final drive ratio. That change is a fitment question as much as a size question.
Keep front and rear comparisons apart, then check the pair together for clearance. A rear tire that is wider or taller than the frame allows can rub the swingarm or the exhaust. Measure before you change anything.
Checking fitment before you change size
Tire fitment is the check that a chosen size physically works on the bike and the rim. Rim width comes first, because a tire outside the maker's recommended range may sit badly. Overall diameter comes next, because it sets clearance.
Look at the gap to the swingarm, the fork legs, the fender and the chain. Turning the wheel by hand while it is off the ground reveals contact that a static look misses. Brake and chain components must also clear the wider or taller tire.
Fitting a tire and checking clearance can hurt a person or damage a bike if it is done carelessly. Have a trained technician mount and inspect a size change you are unsure about. Ride only after the fitment has been confirmed.
- Confirm the rim width range for the chosen tire.
- Compare the new overall diameter with the old one.
- Check clearance to the swingarm, fork and fender.
- Turn the wheel by hand to look for contact.
- Have a technician check a size change before riding.
Avoiding errors in a size comparison
The main error in a dirt bike tire size comparison is mixing units without noticing. Section width is in millimeters while rim diameter is in inches. Convert one to the other before you add anything together.
Another error is treating the sidewall figures as measured values. Section width and aspect ratio are nominal, and the mounted tire can sit slightly differently. Use the calculated overall diameter as an estimate, then confirm with a physical check.
Do not compare a front size with a rear size and expect a match. Match rim diameter within a position first, then compare width and sidewall height. A clear note of each number and its unit keeps the comparison honest.
Dirt bike tire size questions
How do I compare two dirt bike tire sizes?
Compare dirt bike tire sizes by matching rim diameter first, then reading section width and aspect ratio. Convert the rim diameter into millimeters and calculate overall diameter for each size. Two tires on the same rim can still differ in width and height, so all three numbers matter.
What do the sidewall numbers mean on a dirt bike tire?
The sidewall numbers on a dirt bike tire give section width, aspect ratio and rim diameter in that order. Section width is in millimeters, the aspect ratio is a percentage, and the rim diameter is in inches. These are nominal figures that depend on the rim width the tire is mounted on.
How is overall diameter calculated for a dirt bike tire?
Overall diameter is calculated by multiplying section width by the aspect ratio, doubling that section height, and adding the rim diameter. Keep the units consistent by converting the rim diameter to millimeters. The result is an estimate of the mounted tire height.
Can I fit a wider tire on the same rim?
A wider dirt bike tire can fit the same rim only if the rim width sits within the range the tire maker specifies. Outside that range the sidewall profile changes and the tire may sit badly. Check clearance to the swingarm, chain and fender before fitting a wider size.
Does a larger overall diameter change how the bike rides?
A larger overall diameter on a dirt bike raises the tire and changes the effective final drive ratio. The change can affect gearing, ground clearance and clearance to the frame. Confirm the fitment with a technician before you rely on a taller size.