Alternate Tire Sizes for a Car: Options and How to Check Them

Learn how to pick alternate tire sizes for a car, compare overall diameter and load index with the original size, and check rim width and clearance before fitting.

8 min read1 views
— · 0 votes
Contents
  1. Start with the original tire size
  2. How to compare overall diameter
  3. Equivalent sizes with the same diameter
  4. Check rim width and load index
  5. Run a clearance check on the car
  6. Original vs alternate tire size in practice
  7. Use a fitment guide and confirm approval
  8. Questions About Alternate Tire Sizes
  9. Can I change my car tire size?
  10. What are comparable tire sizes to 285 65R20?
  11. Can I change tire size and keep the same diameter?
  12. How do I check alternate tire size fitment on my car?
  13. What is the difference between original equipment and alternate tire sizes?
  14. Will a different tire size change my speedometer?

An alternate tire size is a size other than the factory tire size that still fits your car's wheel and body without rubbing or changing the gearing too much. You can change your tire size, but only after comparing overall diameter, load index, speed rating, rim width and clearance against the original equipment size. The safest starting point is the sidewall markings of the tires already on the car.

  • Read the original tire size from the sidewall before comparing any alternatives.
  • Keep the overall diameter close to the factory size to limit speedometer error.
  • Match or exceed the original load index and speed rating for your vehicle.
  • Check rim width for the new tire and confirm clearance at full steering lock.
  • Verify that the new size is listed as an approved size for your vehicle.

Start with the original tire size

Every alternate tire size search begins at the sidewall of the tires already on your car. The sidewall size code shows width, aspect ratio, construction and wheel diameter in one string. This factory tire size is the baseline for every comparison you make later.

Write the original size down exactly, including the load index and speed rating that follow the dimensions. Those two numbers matter as much as the width and rim diameter. Tire size options for your car are only equivalent when they carry at least the same load and speed capability.

The owner's manual and the tire placard on the door jamb repeat the OE tire size, so use them to confirm the sidewall reading. Approved tire sizes for a vehicle often appear there too. If the placard lists more than one size, each is a factory-approved option.

How to compare overall diameter

Overall diameter is the measurement that decides whether an alternate size behaves like the original. A comparable tire size keeps the rolling diameter close to the factory figure. When the diameter changes, the speedometer, odometer and final drive gearing shift with it.

A tire size calculator converts the sidewall numbers into a rolling diameter so you can compare sizes directly. The width times the aspect ratio gives the sidewall height, which doubles and adds to the wheel diameter. That figure is the overall height you compare between the original and the alternative.

Some tolerance in rolling diameter is acceptable, but the closer the match, the less speedometer error you introduce. An overall diameter comparison across two or three candidate sizes shows which ones sit nearest the OE size. Record the difference rather than eyeballing the numbers.

  • Note the original width, aspect ratio and wheel diameter.
  • Calculate sidewall height from width and aspect ratio.
  • Double the sidewall height and add the wheel diameter.
  • Compare each candidate size against the original diameter.
  • Keep the closest match where speedometer accuracy matters.

Equivalent sizes with the same diameter

An equivalent tire size changes the width and aspect ratio together to keep the diameter close to the original. Going one step wider usually means going one step lower in aspect ratio. This is how plus sizing works, moving up in wheel size while holding the overall diameter near the factory figure.

Plus-one and plus-two sizing raise the wheel diameter and drop the sidewall to compensate. The overall height stays close to the original, so gearing and speedometer readings barely change. Each step needs a wider rim and a tire rated for that rim width.

Comparable tire sizes to 285 65R20 follow the same logic, trading width against aspect ratio to hold diameter. The alternative tire size guide you build from these comparisons is only as good as the original measurement. Confirm each equivalent size against the approved list for the vehicle.

Check rim width and load index

Rim width sets the range of tire widths that seat correctly on your wheel. A tire that is too wide or too narrow for the rim can wear unevenly and seat poorly. Every tire size carries a recommended rim width range, and the alternative must fall inside it.

Load index and speed rating must meet or exceed the original equipment figures. A lower load rating reduces the tire's capacity to carry the vehicle. The load index appears on the sidewall after the size and is easy to misread, so compare it carefully.

Dual fitment describes a wheel that accepts more than one bolt pattern, and it does not change the rim width rule. Alternate tire size fitment depends on the wheel, not only the tire. Check the rim width marking on the wheel before ordering any alternative size.

Run a clearance check on the car

A clearance check confirms the alternative tire does not touch the body, suspension or brakes. Turn the steering to full lock in both directions and look at the gap to the inner fender and suspension parts. Check the rear as well, since the rear arches and suspension differ from the front.

A wider tire can rub the inner liner or the strut even when the diameter matches. Lower profile alternatives on larger wheels can contact brake calipers or suspension arms. Measure the gap with the car on the ground and the wheels straight, then repeat at full lock.

Any rubbing means the size is not a compatible alternate tire size for your car. Do not drive on a tire that contacts the body or suspension, because it can damage the tire and the car. A trained technician can confirm clearance where a visual check is not conclusive.

Original vs alternate tire size in practice

The original tire size is the reference, and the alternate size is judged against it on four counts. Diameter, rim width, load rating and clearance each have to pass before the alternative is usable. A size that fails one of these checks is not an acceptable tire size alternative.

Choosing an alternative tire size for looks alone can cost you speedometer accuracy or load capacity. Choosing one for a specific purpose, such as a winter set or a different wheel, keeps the decision grounded. State the purpose before you compare sizes so the trade-offs are clear.

An original vs alternate tire size comparison is a simple table of dimensions and ratings. Fill in diameter, rim width range, load index and speed rating for both sizes. The row that matches on every count is the size to consider first.

CheckOriginal sizeAlternate size
Overall diameterFrom sidewallWithin tolerance
Rim width rangeWheel markingInside range
Load indexSidewallEqual or higher
Speed ratingSidewallEqual or higher
ClearanceNot applicableNo contact at full lock

Use a fitment guide and confirm approval

A tire size fitment guide lists the sizes a vehicle can take, and it starts from the OE size. An alternate tire size finder works the same way, matching your original size to equivalent options. Use the guide to shortlist sizes, then check each one on the car.

Check that the alternative appears as an approved tire size for the vehicle where such a list exists. Approved tire sizes for a vehicle reflect testing by the manufacturer, and stepping outside them shifts the risk to you. A size that is dimensionally close can still be unapproved for the car.

The fitment check is the final gate before you buy. Confirm diameter, rim width, load index, speed rating and clearance for the chosen size. Only then order tires and book the fitting with a trained technician.

Questions About Alternate Tire Sizes

Can I change my car tire size?

Yes, you can change your car tire size when the alternative keeps the overall diameter close to the original and meets the load index and speed rating. The new tire must fit the rim width range and clear the body and suspension at full lock. Confirm the size is approved for your vehicle before fitting it.

What are comparable tire sizes to 285 65R20?

Comparable tire sizes to 285 65R20 are those that keep a similar overall diameter while trading width against aspect ratio. A narrower tire needs a taller aspect ratio and a wider tire needs a shorter one to hold the diameter. Calculate each candidate before assuming it matches.

Can I change tire size and keep the same diameter?

Yes, you can change tire size and keep the same diameter by adjusting width and aspect ratio together. This is what plus sizing does when it moves to a larger wheel with a shorter sidewall. The overall diameter stays close, so the speedometer reading changes very little.

How do I check alternate tire size fitment on my car?

Alternate tire size fitment is checked by comparing diameter, rim width range, load index and speed rating against the original size. Then turn the steering to full lock and look for contact with the inner fender, suspension or brakes. Any rubbing means the size does not fit.

What is the difference between original equipment and alternate tire sizes?

The original equipment tire size is the factory specification, while an alternate size is any other size that still fits and performs acceptably. The alternate must match the original on load index and speed rating and stay close in overall diameter. Rim width and clearance decide whether the alternative is usable.

Will a different tire size change my speedometer?

Yes, a different tire size changes your speedometer reading when the overall diameter differs from the original. A larger diameter makes the speedometer read lower than actual speed, and a smaller one makes it read higher. Keeping the rolling diameter close to the factory size limits the error.

Read next

Latest articles