# Work and Cargo Van Tire Sizes

Learn how to read work and cargo van tire sizes, decode LT metric codes, compare load ranges, and match dimensions to your van's rated capacity.

Work and cargo van tire sizes are written in a metric or LT metric code on the sidewall, and that code gives you the width, the aspect ratio, the construction and the wheel diameter. Reading it correctly matters because a cargo van carries loads that a passenger car tire was never built for. The numbers tell you not just the size, but also the load capacity you need to match. 

- The sidewall code gives section width, aspect ratio, construction type and rim diameter in that order.
- LT metric sizing adds a light truck load range such as C, D or E to the basic metric format.
- The load index must meet or exceed the axle rating on your van's certification label.
- Tire diameter and width both change when you move away from the original size, and that affects clearance and speedometer accuracy.
- Matching the original size keeps clearance, gearing and load capacity as the manufacturer designed them.
 

## What a cargo van tire size code means 

A cargo van tire size is a single string of numbers and letters pressed into the sidewall. The format follows a fixed order, so each part tells you a specific dimension. Reading the code left to right is the fastest way to understand what you are looking at. 

A plain metric code such as 225/75R16 breaks into four parts. The 225 is the section width in millimeters, the 75 is the aspect ratio as a percentage of that width, the R means radial construction and the 16 is the wheel diameter in inches. The sidewall size code always follows this order, with the width and rim in different units. 

The aspect ratio is where many people get caught out. It is not a measurement in millimeters but a proportion of the width, so a 75 series tire is taller than a 65 series of the same width. Understanding this explains why two tires with similar numbers can sit at different heights on the van. 

## Light commercial and LT metric sizing 

Light commercial tire sizing uses the same base numbers but adds a load designation that passenger tires do not carry. The LT prefix stands for light truck, and it signals that the carcass is reinforced for higher inflation pressures and heavier loads. This is the sizing family that work vans draw from. 

A typical LT metric code looks like LT245/75R16 with a load range letter printed separately. The load range C, D or E describes how much pressure and load the tire can handle in its class. Each step up in load range means a stronger sidewall and a higher maximum inflation pressure. 

Some commercial vans use a metric size without the LT prefix but still carry a high load index. Commercial van tyre dimensions in that format still give you width, aspect ratio and rim size. The [load index and speed rating](/articles/tire-load-index-load-range-speed-ratings-material-44528/) printed near the size tell you the carrying capacity and the top sustained speed. 
| Code part | Example | What it tells you | 
| Section width | 225 | Tire width in millimeters | 
| Aspect ratio | 75 | Sidewall height as a percent of width | 
| Construction | R | Radial build | 
| Rim diameter | 16 | Wheel size in inches | 
| Load range | E | Carcass strength and pressure class |  

## Reading load index and speed rating 

The load index and speed rating sit next to the size code and together they define the tire's working limits. The load index is a number that maps to a maximum carrying capacity per tire. The speed rating is a letter that maps to a maximum sustained speed under load. 

A cargo van tire must meet or exceed the load figure your van is rated for. The axle capacity is printed on the vehicle certification label, which sits on the driver door jamb or in the door frame. Comparing the tire's rated capacity against that figure is the check that matters. 

Do not fit a tire with a lower load index than the original even if the size matches. Lower ratings reduce the safety margin when the van is loaded. A trained tire technician can confirm the correct load index and speed rating for your model if the label is unclear. 

## How to compare cargo van tire dimensions 

Cargo van tire dimensions go beyond the sidewall code, because the code does not print the overall diameter. Tire diameter and width can be calculated or looked up in a size chart, and both affect fit. Knowing them lets you compare a replacement against the original. 

Overall diameter is the rim diameter plus twice the sidewall height. Sidewall height comes from the section width multiplied by the aspect ratio. A wider tire with a lower aspect ratio can keep the same diameter, while a taller aspect ratio increases it. 

A cargo van [tire size chart](/articles/commercial-truck-and-bus-tire-sizes-common-sizes-and-their-dimensions/) lists these calculated values side by side so you can compare options. Charts are useful for spotting a size that keeps diameter close to the original. Use the chart as a reference and confirm clearance on the actual van before committing. 

## When you can change from the original size 

Changing a work van tire size is possible only within limits set by clearance and load capacity. Moving to a wider or taller tire can cause rubbing on suspension parts, wheel arches or brake lines. The change also affects speedometer accuracy and effective gearing. 

A small change in width is generally easier to accommodate than a large change in diameter. Diameter changes alter the rolling circumference, which changes the distance the van travels per wheel revolution. The speedometer and odometer then read differently from the true speed and distance. 

Fitting a different size also means checking the wheel width and the load index again. A tire that is too wide for the rim will not seat correctly, and a tire with too low a load index is unsuitable for cargo work. Ask a trained specialist to verify fitment before you buy a non-original size. 

## Checking fitment before you buy 

Fitment checks confirm that a tire size physically fits the van and the wheel. The first check is the wheel width range for the chosen section width. The second is clearance to suspension, bodywork and brakes through the full steering and suspension travel. 

Reading the vehicle certification label gives the original size and the recommended inflation pressures. The owner's manual adds any notes about load range and speed rating for the model. Both are reliable starting points when you replace tires. 

A trained tire technician can mount a test fit and check clearance with the van loaded as you drive it. Verifying fitment before purchase avoids returns and avoids damage from rubbing. The check takes little time and protects both the tire and the vehicle. 

## Keeping the size matched across the van 

All tires on a cargo van should match in size, load range and construction. Mixed sizes or mismatched load ranges can change handling and load distribution. On dual rear wheel vans, matching across the pair is especially important for even load sharing. 

When only one tire needs replacement, fit the same size and load range as the others. A different diameter on one corner affects how the van tracks and how the differential works. Keeping the set consistent preserves the behavior the manufacturer designed. 

Record the sidewall code of your current tires before you shop. Having the exact code, load index and speed rating in hand makes the replacement straightforward. A tire technician can source the matching size and confirm the load rating against your van. 

## Cargo van tire size questions 

### What is the tire size for a cargo van? 

A cargo van tire size is not one fixed number, because it depends on the model, the wheel option and the load rating. The size is printed on the sidewall of the tires currently fitted, and the original size is on the vehicle certification label. Use those two sources to identify the correct size for your van. 

### What does LT mean in a work van tire size? 

LT stands for light truck, and it marks a tire built with a reinforced carcass for heavier loads. A work van tire size with the LT prefix carries a load range letter such as C, D or E alongside the metric code. The LT designation tells you the tire is rated for higher inflation pressures than a passenger tire. 

### How do I read commercial van tyre dimensions? 

Commercial van tire dimensions appear in the sidewall code in a fixed order: section width, aspect ratio, construction and rim diameter. A code such as 225/75R16 means 225 millimeters wide, an aspect ratio of 75 percent, radial construction and a 16 inch rim. The load index and speed rating sit next to that code. 

### Can I change my van's tire size? 

You can change the size within limits set by clearance, wheel width and load capacity. A larger diameter changes speedometer accuracy and gearing, and a wider tire may rub on suspension or bodywork. A trained tire technician should verify fitment before you commit to a different size. 

### What load range do I need for a cargo van? 

The load range must give a load index that meets the axle rating on your van's certification label. Load range C, D and E each represent a step in carcass strength and maximum inflation pressure. Match the load index to the rated capacity rather than choosing by size alone.
