# Wheel Width Size Chart: Common Rim Widths by Diameter

See typical rim widths for each wheel diameter, learn how J-width is measured, and match tire section width to the right rim width range.

A wheel width size chart lists the rim widths found on each wheel diameter, stated in inches. Passenger rims range from roughly 4 inches wide at 13-inch diameter to 11 inches at 20 inches. The correct width for your car depends on the [tire section width](/articles/tire-width-chart/) and the space in the wheel well. 

- Rim width is measured inside the flanges, where the tire beads sit, not across the outer lips.
- Widths step in half-inch increments, and larger diameters carry a wider spread of widths.
- Every tire size has an approved [rim width range](/articles/approved-rim-widths-by-tire-size-checking-tire-and-rim-compatibility/) listed in the tire maker's data.
- A half-inch change in rim width shifts tire section width by roughly 5 millimeters.
- A wider wheel at the same offset reaches further toward both the strut and the fender.
 

## How to read the width in a wheel code 

The width in a wheel size code is the first number, such as 7.5 in 7.5Jx17. That figure is the rim width in inches between the bead seats, where the tire edges rest. The number after the x is the rim diameter, also measured in inches. Together, these two numbers locate the wheel on any rim width chart. 

The letter J in a wheel code describes the shape of the rim flange, not the width. A flange is the raised lip that holds the tire bead in place sideways. J is the standard flange profile for passenger cars and light vehicles. Other letters, such as B or JJ, mark different flange heights and shapes. 

The x between width and diameter marks a one-piece rim with a drop center. A drop center is the deep well that lets the tire bead pass over the flange during mounting. A dash in place of the x marks a multi-piece rim. Offset, written as ET followed by millimeters, often appears next to this code. 

## How rim width is measured in inches 

Rim width is measured from the inside of one flange to the inside of the other. That distance is called J-width, the same number stamped in the wheel code. Measuring across the outer lips gives a larger figure that matches no sizing chart. The tire sizing system always works from the bead seat width. 

Overall wheel width is the full distance across both outer lips of the rim. On a passenger wheel, overall width runs about one inch more than the stated J-width. A wheel listed as 8 inches therefore measures close to 9 inches across the lips. Clearance checks use overall width, while tire fitment uses J-width. 

To measure a bare wheel, stand it upright and use a tape measure across the barrel. Measure between the inner edges of the two flanges, where the tire beads sit. Round the result to the nearest half inch, because rim widths come in half-inch steps. A mounted tire hides the bead seats, so read the stamped code instead. 

## Rim widths by diameter for passenger cars 

Rim widths by diameter follow a clear pattern: larger wheels carry a wider spread of widths. Small 13-inch and 14-inch rims sit between about 4 and 7 inches wide. Rims of 17 inches and up start near 6.5 inches and reach 9 inches or more. Widths change in half-inch increments, such as 6, 6.5 and 7 inches. 

The chart below shows typical width ranges for passenger car and light SUV wheels. Original equipment wheels tend to sit in the lower and middle part of each range. Figures at the top of each range appear mainly on performance and aftermarket wheels. Trucks and heavy vehicles use separate rim standards not covered in this chart. 

A width outside the listed range for its diameter is possible but rare on road cars. Such a wheel needs a matching tire size and a careful clearance check. The chart helps you judge whether a quoted width sounds normal for its diameter. Exact fitment for a given car comes from its maker's wheel specification. 
| Rim diameter (in) | Typical J-width range (in) | Example wheel codes | 
| 13 | 4.0 to 6.0 | 4.5Jx13, 5.5Jx13 | 
| 14 | 4.5 to 7.0 | 5Jx14, 6Jx14 | 
| 15 | 5.0 to 8.0 | 6Jx15, 7Jx15 | 
| 16 | 5.5 to 8.0 | 6.5Jx16, 7Jx16 | 
| 17 | 6.5 to 9.0 | 7Jx17, 8Jx17 | 
| 18 | 7.0 to 10.0 | 7.5Jx18, 8.5Jx18 | 
| 19 | 7.5 to 10.5 | 8Jx19, 9Jx19 | 
| 20 | 8.0 to 11.0 | 8.5Jx20, 10Jx20 |  

## Matching tire section width to rim width 

Tire section width is the first number in a metric tire size, given in millimeters. In 225/45R17, the tire is 225 millimeters wide when mounted on its measuring rim. The measuring rim is the specific width the tire maker uses to state its dimensions. Each tire size also has an approved range of narrower and wider rims. 

Tire width compatibility is set by an approved rim width range for every tire size. Standards bodies, including the European Tyre and Rim Technical Organisation and the Tire and Rim Association, publish these ranges. Mounting a tire outside its range can unseat the bead or overload the sidewall. The tire maker's data sheet gives the exact range for each specific size. 

The table gives approximate fit ranges for passenger tires by section width. Ranges shift slightly with aspect ratio, the sidewall height figure after the slash. Low-profile sizes often accept a wider rim than tall-sidewall sizes of the same width. Treat the table as a guide and confirm with the specific tire's data. 
| Tire section width (mm) | Section width (in) | Approximate approved rim range (in) | 
| 185 | 7.3 | 5.0 to 7.0 | 
| 195 | 7.7 | 5.5 to 7.0 | 
| 205 | 8.1 | 5.5 to 7.5 | 
| 215 | 8.5 | 6.0 to 8.0 | 
| 225 | 8.9 | 6.0 to 8.5 | 
| 235 | 9.3 | 6.5 to 9.0 | 
| 245 | 9.6 | 7.0 to 9.0 | 
| 255 | 10.0 | 7.5 to 9.5 | 
| 265 | 10.4 | 7.5 to 10.0 | 
| 275 | 10.8 | 8.0 to 10.5 |  

## How rim width changes tire dimensions 

Rim width changes the mounted section width of a tire, even though the size marking stays the same. A rim wider than the measuring rim spreads the beads and widens the sidewalls. A narrower rim pulls the beads together and makes the tire slightly narrower. Tread width changes much less than section width does. 

Each half-inch change in rim width shifts tire section width by roughly 5 millimeters. A 225 tire on a rim one inch wider than its measuring rim measures near 235 millimeters. The overall diameter of the tire stays almost unchanged by rim width. Speedometer readings therefore do not shift noticeably from a width change alone. 

Sidewall shape also follows rim width and affects how the tire looks and steers. A narrow rim gives a rounded, bulging sidewall that flexes more in corners. A wide rim pulls the sidewall straighter and firms up steering response. Stretching a tire past its approved rim range is unsafe and can let the bead slip off. 

## Narrow versus wide wheels compared 

Narrow and wide wheels of the same diameter differ in tire choice, ride and steering feel. A narrower wheel takes tires with a smaller section width and more sidewall flex. Narrow setups ride more softly and suit winter tires meant to cut through snow. Lower weight is another trait of a narrower wheel in the same design. 

A wider wheel carries a wider tire and holds the sidewall more upright. Steering response feels sharper because the sidewall twists less under cornering load. The contact patch, meaning the tire's footprint on the road, can grow wider and change grip. Wider wheels also add weight and place the rim lip closer to curbs. 

Plus sizing, which means fitting a larger rim diameter with a lower-profile tire, often adds width too. Moving from a 16-inch to an 18-inch wheel may raise width by half an inch to an inch. The new tire needs a shorter sidewall to keep the overall diameter close to the original. A [tire size chart](/articles/commercial-truck-and-bus-tire-sizes-common-sizes-and-their-dimensions/) helps match the new [section width and aspect ratio](/articles/comparing-tire-width-and-aspect-ratio/) to the new rim. 

## Checking clearance before changing wheel width 

Wheel width and offset work together to decide where the tire sits in the wheel well. Offset is the distance in millimeters from the wheel's centerline to its mounting face. Extra width at the same offset splits evenly between the inner and outer side. One additional inch of width moves each edge about half an inch further out. 

Backspacing measures, in inches, the distance from the mounting face to the inner rim lip. A wider wheel with unchanged backspacing pushes all the added width outward. Inner clearance matters for struts, springs, brake calipers and steering parts. Outer clearance matters for fender lips, especially when the suspension compresses or the wheels turn. 

A wheel and tire fitment change on a specific car needs measurement, not just a chart. The vehicle maker's wheel specification lists approved widths, offsets and load ratings. A tire and wheel specialist can test-fit or measure the car before a final purchase. Mounting tires on rims and seating the beads under pressure are jobs for a trained technician. 

## Wheel and rim width questions 

### Is wheel width the same as tire width? 

No, wheel width and tire width are separate measurements in different units. Wheel width is the J-width in inches between the bead seats. Tire width is the section width in millimeters across the inflated sidewalls. A passenger tire measures wider than the J-width of the rims it is approved for. 

### Where can I find the width of my wheels? 

The width of a wheel is stamped on the wheel itself, in a code such as 7Jx16. Look on the back of the spokes, inside the barrel or around the hub mounting area. The vehicle maker's specification sheet also lists factory wheel sizes. Some door jamb placards show the tire size but not the rim width. 

### Can I put a wider tire on my current rims? 

Yes, a wider tire can go on your current rims if their width falls inside its approved range. The tire maker's data for the new size shows that range. The wider tire must also clear the suspension and bodywork at full steering lock. Rim diameter cannot change, since the tire must match the rim diameter exactly. 

### How do I convert rim width from inches to millimeters? 

Multiply the rim width in inches by 25.4 to get millimeters. A 7-inch rim equals about 178 millimeters, and an 8-inch rim about 203 millimeters. Converting helps you compare rim width directly with tire section width. Keep in mind that a tire's section width sits above the rim width in millimeters. 

### Do front and rear wheels have to be the same width? 

No, front and rear wheels do not need the same width on every car. Some vehicles leave the factory with a staggered setup, meaning wider wheels and tires at the rear. A staggered setup should follow the vehicle maker's listed sizes for each axle. Rotating tires from front to rear is then limited or not possible.
