# Wheel Offset Markings: Finding and Reading the Offset Stamped on a Wheel

Learn where the offset is stamped on a wheel, what the ET number and millimeters mean, and how offset compares with wheel width and backspacing.

A wheel offset marking is the number stamped on the wheel that tells you how far the hub mounting surface sits from the wheel centerline. On alloy wheels it appears as an ET value followed by millimeters, and on steel wheels it may be stamped near the valve hole or on the inner rim face. Reading that stamp is the starting point for matching a wheel to a vehicle and to a tire size. 

- The offset stamp tells you the distance in millimeters between the hub mounting surface and the wheel centerline.
- The letters ET come from the German term for offset and always sit in front of the number.
- A positive number means the mounting surface sits outboard of the centerline, and a negative number means it sits inboard.
- The offset stamp is often on the back of the spokes or near the valve stem, so clean the wheel before you look.
- Offset and wheel width are separate markings, and you need both to compare fitment.
 

## What a wheel offset number means 

Wheel offset is the distance in millimeters from the wheel centerline to the hub mounting surface. The spacing of the mounting surface decides how far the whole wheel sits inboard or outboard on the car. A change in offset moves the tire relative to the fender and the suspension. 

The offset number alone does not describe the wheel fully, because width sets the centerline it is measured from. Two wheels with the same offset but different widths sit in different places on the car. That is why a rim offset number is only meaningful next to the wheel width. 

Offset can be positive, zero or negative. Positive offset places the mounting surface toward the outer face of the wheel, and negative offset places it toward the inner face. Zero offset puts the mounting surface on the centerline itself. 

## Where the offset is stamped on a wheel 

The offset stamp location varies with the wheel design, and the inner rim face is a good place to start. Many wheels carry the stamping on the back of the spokes around the hub. Steel wheels often show it near the valve hole or on the rim barrel. 

Cast or forged alloy wheels usually carry a raised or engraved panel with several markings together. The wheel width marking and the offset stamping are often placed on the same panel. Look for a short string of numbers and letters rather than a single figure. 

Dirt, brake dust and paint can hide shallow stampings, so clean and light the wheel before you search. If nothing shows on the visible faces, check the inner side of the wheel while it is off the car. A trained technician can confirm the marking when the stamp cannot be found. 

## Reading the ET marking and its millimeters 

The ET marking is the label that identifies the offset, and the number after it is the offset in millimeters. An ET38 stamp means an offset of 38 millimeters, and the figure is always given as a whole number on most wheels. The letters come from the German word for offset and are used worldwide. 

A stamp may combine the offset with other figures, such as the width and the diameter. Read each group separately instead of treating the string as one number. The width marking often looks like 7.5J, while the offset looks like ET38. 

A negative offset appears with a minus sign, such as ET-10. Wheels with zero offset may show ET0 or a similar form. If the sign is missing or worn, have the offset measured rather than assumed. 

## Telling offset apart from backspacing 

Backspacing is a different measurement, taken from the inner edge of the wheel to the hub mounting surface. Offset is measured from the wheel centerline instead, so the two figures are not interchangeable. Backspacing is measured in inches on many wheels and in millimeters on others, which adds to the confusion. 

A wheel with more positive offset generally has more backspacing for the same width, because the mounting surface moves toward the outer face. The relationship depends on the wheel width, so one value cannot be converted to the other without it. Knowing the width lets you translate between the two when comparing wheels. 

Backspacing helps when you check clearance to the suspension and inner wheel well. Offset helps when you compare how the wheel face sits relative to the fender. Use the number that answers the question in front of you, and keep both on hand when you shop. 

## Matching offset markings to wheel width 

Wheel width and offset markings belong together, since the centerline used for offset depends on the width. A rim stamp typically shows both, and reading only one leaves the fitment picture incomplete. Note both figures before you compare any two wheels. 

Width is often marked in inches, while offset is marked in millimeters. A wheel marked 8J with ET45 is 8 inches wide with an offset of 45 millimeters. Mixing the units is a frequent source of error, so convert before you calculate. 

Changing width while keeping offset shifts the wheel faces in different directions on each side. That is why a wider wheel with the same offset does not sit exactly where the old one did. Record the width and offset as a pair whenever you record a wheel size. 

## Steps for finding and recording the offset 

Finding the wheel offset stamping takes a careful look and a clean wheel. Work from the outer face to the inner face, and check the full barrel if the first spots show nothing. Write down every marking you find instead of only the offset. 

Photograph the stamping while the wheel is off the car, then read the photo later. A photo lets you confirm the digits without crawling under the vehicle again. Note the width, diameter and offset as one line so the numbers stay tied together. 

Confirm any figure you plan to use for a purchase with a technician or the wheel maker. A worn stamp can turn a 3 into an 8, and a wrong offset affects clearance and handling. Treat an unreadable stamp as unknown until it is measured. 

## Offset and the tire that goes on the wheel 

The offset marking tells you where the wheel sits, while the tire size tells you how much rubber wraps it. The two work together, because a wide tire on a high-offset wheel can move the tire closer to suspension parts than expected. Always judge tire fitment with the wheel width and offset in view. 

A tire sidewall carries its own codes for width, aspect ratio and rim diameter. The rim diameter in the tire code must match the wheel, and the wheel width recommends the tire width range. Offset does not appear on the tire at all, so the wheel stamp is the only source for it. 

Check clearance after any wheel change, turning the steering from lock to lock and looking at the inner fender. If a tire or wheel rubs, stop and consult a specialist before driving. Offset changes can affect handling and bearing load, so any shift away from the original figure deserves professional advice. 

## Questions about wheel offset markings 

### Where is the offset stamped on a rim? 

The offset is stamped on the rim in different places depending on the design. Look on the back of the spokes around the hub, on the inner rim face, or near the valve hole. Alloy wheels often group it with the width on one panel. 

### What does the ET on a wheel mean? 

ET is the label for the offset value, taken from the German word for offset. The number after it gives the offset in millimeters. An ET40 wheel has an offset of 40 millimeters, measured from the wheel centerline to the hub mounting surface. 

### What does a wheel offset number mean in practice? 

The wheel offset number shows how far the mounting surface sits from the centerline. A larger positive figure tucks the wheel inboard, and a smaller or negative figure pushes it outboard. The result also depends on wheel width. 

### How do wheel width and offset markings work together? 

Wheel width sets the centerline that offset is measured from, so the two markings must be read as a pair. A wider wheel with the same offset does not sit in the same place. Note both numbers before you compare wheels. 

### Can I read the offset without taking the wheel off? 

You can sometimes read the offset with the wheel on the car, by looking behind the spokes at the hub area. A clean, well-lit view helps, and a phone camera can reach awkward spots. If nothing is visible, have the wheel removed or measured by a technician. 

### Is offset the same as backspacing? 

No, offset and backspacing are measured from different starting points. Offset runs from the wheel centerline, and backspacing runs from the inner edge of the wheel. The difference between them depends on the wheel width, so you need that figure to compare the two.
