Used Tractor Tire Size Chart in Inches

Read a used tractor tire size chart in inches: learn overall diameter, section width, rim diameter, load index and how to match a used tire to your wheel.

8 min read1 views
— · 0 votes
Contents
  1. What a used tractor tire size chart shows
  2. How to read the sidewall markings
  3. Calculating overall diameter in inches
  4. Section width and rim diameter in inches
  5. Comparing a used tire with your current size
  6. Load index and inflation on a used tire
  7. Checking a used tire before you buy
  8. Used Tractor Tire Size Questions
  9. How do I read a used tractor tire size chart in inches?
  10. Can I fit a used tractor tire that is a different size?
  11. What does the load index mean on a used tractor tire?
  12. How is overall diameter measured in inches?
  13. Does section width include the tread or the sidewall?
  14. Can I mount a used tractor tire myself?

A used tractor tire size chart in inches converts the sidewall markings of an agricultural tire into three measurements: overall diameter, section width and rim diameter. Those inch figures let you compare a used tire against the tire already on your machine before you buy. The load index on the sidewall adds the carrying capacity that the numbers alone do not show.

  • Read the sidewall first, then translate its markings into overall diameter, section width and rim diameter in inches.
  • Match the rim diameter exactly, because a used tire must sit on the wheel you already have.
  • Compare overall diameter to keep ground speed and clearance close to the original setup.
  • Check section width for clearance to the fender and the row spacing on your machine.
  • Confirm the load index meets or exceeds what your tractor axle carries.

What a used tractor tire size chart shows

A used tractor tire size chart in inches lists three geometric figures for each tire: overall diameter, section width and rim diameter. Overall diameter is the height of the inflated tire from the ground to the top of the tread. Section width is the widest point across the tire body when it is mounted and inflated.

Rim diameter is the measurement of the wheel the tire seats on, taken across the bead seat. A chart in inches keeps all three figures in one unit, which makes comparison simple. Agricultural tire markings on the sidewall are the source of every number in the chart.

Used tires keep the same molded size as new ones, so the chart applies to both. Wear changes the tread depth and the overall diameter by a small amount. Inspect the casing and tread of a used tire rather than trusting the chart alone.

How to read the sidewall markings

Agricultural tire markings follow a pattern, and reading that pattern is the first step before any chart. A size such as 18.4-38 gives the section width in inches first, then the rim diameter in inches. The decimal figure is the section width, and the number after the dash is the wheel size.

Some tires use a three-part size, with a ratio figure in the middle. In that format the first number is the section width in inches, the second is the aspect ratio, and the third is the rim diameter. A radial tire may add the letter R between the ratio and the rim figure.

The load index appears as a number near the size, and it states the load the tire can carry at a set inflation pressure. Star ratings or ply ratings may also appear on agricultural tires. Write down every marking on the sidewall before you open a chart.

Calculating overall diameter in inches

Overall diameter in inches comes from the sidewall height plus the rim diameter, and the chart shows the result. When the sidewall gives a section width and an aspect ratio, multiply the width by the ratio to get one sidewall height. Double that height and add the rim diameter to reach the overall diameter.

A tire marked without an aspect ratio is assumed to have a tall sidewall, so the chart figure is the reliable value. Molded sizes already describe the tire in inches, which removes most of the arithmetic. Confirm the figure against the tire you plan to replace.

Overall diameter sets ground speed, drawbar height and clearance under the chassis. A change in overall diameter shifts the gearing between the engine and the ground. Compare the chart figure of the used tire with the original before you commit.

Section width and rim diameter in inches

Section width in inches tells you how much space the tire needs across the machine. The figure is measured at the widest point of the inflated tire, not at the tread face. Fenders, row spacing and steering clearance all depend on this width.

Rim diameter must match the wheel on your tractor exactly, because a used tire cannot be stretched onto a different rim. Check the rim width as well, since a tire needs a rim within the range the maker lists. A rim that is too narrow or too wide changes the shape of the tire.

The chart lists section width and rim diameter side by side for each size. Use both figures together, since a wide tire on the wrong rim will not seat correctly. Measure your existing wheel before you compare charts.

Comparing a used tire with your current size

Comparing a used tractor tire with your current size is a matter of placing three figures side by side. Put overall diameter, section width and rim diameter from your tire next to the same figures from the used tire. Small differences in diameter are tolerable, but the rim must match.

A used tire that is wider than the original may rub the fender or change row spacing. A tire that is taller raises the machine and alters its speed at a given engine setting. Note each difference and decide whether your machine can accept it.

Front and rear tires work as a pair on a four-wheel-drive tractor, and the ratio between them matters. Changing one axle alone can strain the driveline. Keep the original ratio when you substitute a used size.

Load index and inflation on a used tire

The load index states how much weight a tire carries at a stated inflation pressure, and it matters as much as the size. A load index lower than the original reduces the safe capacity of the axle. Check the index on the used tire against the one on your current tire.

Inflation pressure controls how the tire carries its load, and the correct pressure comes from the tire maker and the machine manual. A used tire with a damaged bead or a repaired sidewall may not hold pressure as intended. Have a trained tire technician inspect any questionable casing.

Mounting a large agricultural tire on a rim is a job for a trained specialist with the right equipment. Bead seating and inflation can injure a person or damage the wheel when handled carelessly. Leave the mounting work to a professional shop.

Checking a used tire before you buy

A used tire needs an inspection that the chart cannot provide, so examine the casing and tread yourself. Look for cracks in the sidewall, exposed cords, and repairs that sit outside the tread area. Check the bead for damage, since a torn bead will not seal on the rim.

Measure the tread depth across the tire and note uneven wear, which can point to an alignment or inflation problem. Ask how the tire was stored, because sunlight and ozone age rubber over time. A tire stored flat or outdoors may show damage that a photo hides.

Confirm the size markings on the tire match the chart entry you are reading. A seller may quote a size that does not match the molded marking. Compare the sidewall itself against the chart before any money changes hands.

Used Tractor Tire Size Questions

How do I read a used tractor tire size chart in inches?

You read the chart by matching the sidewall markings to three figures: overall diameter, section width and rim diameter. The used tractor tire size chart in inches lists those figures for each size so you can compare without doing the arithmetic. Start with the molded size on the sidewall, then find that entry in the chart.

Can I fit a used tractor tire that is a different size?

Yes, within limits, provided the rim diameter matches and the differences in diameter and width are small. A used tractor tire that is taller or wider than the original changes clearance, ground speed and row spacing. Keep the front-to-rear ratio intact on a four-wheel-drive machine.

What does the load index mean on a used tractor tire?

The load index is a code for the weight a tire can carry at a stated inflation pressure. A used tractor tire with a lower load index than the original reduces the capacity of that axle. Compare the index on the used tire with the one on the tire you are replacing.

How is overall diameter measured in inches?

Overall diameter is the height of the inflated tire from the ground to the top of the tread. You can calculate it from the section width and aspect ratio, then add the rim diameter. A used tractor tire size chart in inches gives the finished figure for each size.

Does section width include the tread or the sidewall?

Section width is measured at the widest point of the tire body, which is usually the sidewall rather than the tread face. The figure depends on the rim width the tire is mounted on. Check section width in inches against the clearance on your machine.

Can I mount a used tractor tire myself?

No, mounting a large agricultural tire on a rim should go to a trained tire technician with the right equipment. Bead seating and inflation can injure a person or damage the wheel when handled without proper tools. A shop can also check the bead and casing before mounting.

Read next

Latest articles