# Type 1 Gage Study: Method and Interpretation

A plain guide to the Type 1 gage study: how to run a single-part repeatability and bias check, read Cg and Cgk, and tell it apart from gage R&R studies.

A Type 1 gage study measures one part many times with one operator and one gage to judge repeatability and bias. It answers a narrow question: does this gage return the same reading on the same item when nothing else changes? The method suits dimensional checks such as tire sidewall and tread readings where the part itself does not vary. 

- A Type 1 gage study uses one part, one operator and repeated readings, so it isolates the gage from the operator and the part.
- Repeatability comes from the spread of the readings, and bias comes from the gap between their average and a reference value.
- Cg judges repeatability against the tolerance, and Cgk judges both repeatability and bias together.
- Gage R&R studies go further: gage R&R study types split into crossed and nested designs that add operators and part variation.
- A reference value for bias must come from a traceable source, or the bias result means little.
 

## What a Type 1 gage study measures 

A Type 1 gage study measures the repeatability and bias of a single measurement system. One operator takes repeated readings of one part with one gage while every other factor stays fixed. The spread of the readings shows repeatability, and the distance of their average from a reference value shows bias. 

This design is a measurement system analysis tool with a deliberately closed scope. Only the gage contributes variation in a Type 1 study, so the result describes the instrument and not the process around it. Anything that shifts between readings, such as a different operator or a second part, belongs to another study. 

Tire work fits the design well when the item is stable, such as a reference block or a fixed sidewall marking. A single part measurement repeated many times isolates the reading tool from the tire itself. The study tells you how tightly the gage repeats on that one item. 

## Step by step running the study 

A Type 1 gage study starts with a stable part and a known reference value for it. Choose an item whose true dimension is established by a traceable source. Mark the measurement position so each reading lands on the same spot. 

One operator then takes a series of readings of that part, resetting the gage between readings. Reset means removing and replacing the gage, so each reading is independent. Keep the part, the position and the operator unchanged for the whole series. 

Record every reading in order, then compute the average and the standard deviation. The standard deviation drives repeatability, and the difference between the average and the reference value is the bias. A study design that hides any of these numbers cannot be interpreted. 

## Repeatability and bias in the numbers 

Repeatability in a Type 1 gage study is the variation among repeated readings of the same part. Two operators reading the same tire are not part of this number, because only one operator takes part. A small spread means the gage returns a consistent value each time. 

Bias is the systematic offset between the average reading and the reference value. A gage can repeat tightly and still sit away from the truth, so bias and repeatability are read apart. Bias points to calibration, wear or a setup error rather than random noise. 

The reference value must be trustworthy for bias to mean anything. A reference taken from the same gage under test gives no independent check. Use a standard or a value established by a qualified calibration source. 

## Reading Cg and Cgk 

Cg and Cgk are capability ratios that place the gage variation against the tolerance. Cg compares the repeatability spread with the tolerance width. Cgk includes bias, so it drops when the average reading sits away from the reference. 

The capability ratio works like a process capability index, but for the gage alone. A gage that repeats well inside the tolerance earns a high Cg. When bias pulls the average toward a tolerance limit, Cgk falls even if Cg stays high. 

Interpret Cg and Cgk together, never one alone. A high Cg with a low Cgk means a precise gage aimed at the wrong value. The pair tells you whether to adjust the setup or to look for a better instrument. 
| Result | What it suggests | 
| High Cg, high Cgk | The gage repeats tightly and sits on the reference | 
| High Cg, low Cgk | Readings repeat but the average is offset from the reference | 
| Low Cg, low Cgk | The gage spread is wide against the tolerance | 
| Low Cg, high Cgk | An unusual mix, so check the data and the tolerance used |  

## Where Type 1 fits among gage R&R studies 

Gage R&R study types differ in what they let vary, and a Type 1 study varies almost nothing. Gage R&R stands for gage repeatability and reproducibility. Repeatability is one gage repeating, while reproducibility is the shift between operators or setups. 

A crossed gage study has every operator measure every part, so operator and part effects are separated. A nested gage study assigns different parts to different operators, which suits destructive or hard-to-repeat tests. Both designs reach beyond the single-part Type 1 scope. 

Type 1 gage study results do not replace a full gage R&R when operators or part variation matter. Use the Type 1 check to qualify an instrument before the wider study. The wider study then covers reproducibility across people and parts. 

## Choosing the right study for tire readings 

A Type 1 gage study suits a gauge that reads a single stable feature, such as a tread depth tool on one reference tire. The single part measurement keeps tire-to-tire variation out of the result. Pick this design when the question is about the instrument alone. 

Choose a crossed or nested gage study when several technicians take the same tire readings. Operator differences become part of the answer there, and tire variation may also enter. The study type must match the variation you need to see. 

Decide the purpose before collecting data, because the design cannot be widened afterward. A repeatability and bias check answers a gage question, not a process question. Match the method to the decision you need to make. 

## Mistakes that spoil the interpretation 

A Type 1 gage study fails when the part moves or the position changes between readings. Movement adds variation that belongs to the setup, not the gage. Fix the part and mark the spot before the first reading. 

A weak reference value is another source of error, since bias depends on it entirely. Using a nominal print value in place of a measured reference distorts Cgk. The reference must come from an independent, traceable measurement. 

Too few readings give an unstable standard deviation, and mixing operators breaks the single-operator rule. Keep one operator and a consistent reset routine throughout. Record the order of readings so any drift can be seen. 

## Reporting the result plainly 

A Type 1 gage study report should state the part, the reference value, the number of readings and the operator. List the average, the standard deviation, the bias and the Cg and Cgk values. A reader should be able to repeat the study from the report alone. 

State the tolerance used for the ratios, because Cg and Cgk mean nothing without it. Name the reference source so the bias can be judged. Keep the conclusion tied to the gage and the one part tested. 

Avoid claiming the gage is fit for every job based on one study. The result covers repeatability and bias on that part at that time. A different range, part or operator needs its own evidence. 

## Type 1 gage study questions 

### How does a Type 1 gage study fit into measurement system analysis? 

A Type 1 gage study is the narrowest form of measurement system analysis, covering one gage on one part with one operator. It reports repeatability and bias only. Wider measurement system analysis adds operators and parts through gage R&R designs. 

### What are the gage R&R study types? 

The gage R&R study types are crossed and nested designs, alongside the simpler Type 1 study. A crossed gage study has every operator measure every part. A nested gage study gives different parts to different operators, which suits tests that cannot be repeated on the same item. 

### What do Cg and Cgk mean in a Type 1 study? 

Cg measures gage repeatability against the tolerance width, and Cgk adds the effect of bias. A high Cg with a low Cgk shows a gage that repeats well but reads away from the reference. Read both numbers together to interpret the study. 

### Can I run a Type 1 gage study without a reference value? 

No, a Type 1 gage study needs a reference value to calculate bias and Cgk. Repeatability can be computed from the readings alone, but the bias side of the study depends on a traceable reference. Use a standard or a value from a qualified calibration source. 

### Why does a Type 1 gage study use only one part? 

A Type 1 gage study uses one part so that part variation cannot enter the result. The design isolates the gage, which lets repeatability and bias be seen clearly. Operator and part differences belong to a gage R&R study instead.
