# Track Day Tire Pressure

How to set cold track day tire pressure, read the hot pressure gain during sessions, and adjust tire PSI for grip without guessing your track car setup.

Track day tire pressure is set cold and then corrected after the tires heat up, because heat builds pressure during every session. Start from the cold tire pressure the tire maker or the car's manual gives for track use, then measure again right after you come off track. The hot reading tells you how much the tire gained and whether the cold setting needs a change. 

- Set track day tire pressure cold, before the first session, and log every reading.
- Heat adds psi during a session, so recheck the hot pressure as soon as you come in.
- Aim for a hot pressure target rather than trusting the cold number alone.
- Tire temperature and psi move together, so a gauge reading means little without a temperature note.
- Adjust in small steps and change one tire size or brand at a time so the reading stays meaningful.
 

## What track day tire pressure means 

Track day tire pressure is the air pressure you put in the tires before driving on a closed circuit. The number matters because pressure changes the shape of the contact patch against the track surface. A pressure that suits the street can sit far from the figure you want on track. 

The correct figure depends on the car, the tire model and the conditions, so no single psi works for every track car. Tire makers publish track pressure guidance for their own tires, and those brand-specific track pressures override any general rule. The car mass, tire size and track surface temperature shift the target too. 

Read the sidewall first to confirm the size and maximum cold pressure before you touch a gauge. The sidewall numbers describe the tire, not the driving you do, so treat them as a limit and not a target. A trained tire specialist can advise on a specific car and tire combination. 

## Setting cold pressure before the first session 

Cold tire pressure is the reading taken when the tire sits at ambient temperature, before any heat from driving. Measure cold pressure in the morning, before the first track session, while the tires are still cool. Cold pressure before track session work is the base figure you log for the day. 

Use the same pressure gauge readings from the start, because two gauges can disagree on the same tire. A trustworthy dial or digital gauge removes doubt when you compare the morning figure to the hot figure later. Write down each cold psi next to the tire position so the numbers stay organized. 

Set a cold track day tire psi that sits below the hot target you want, since the tire gains pressure as it warms. Tire pressure gain under heat can be substantial on a fast lap, so leave room for the rise. Inflating to the final target when cold pushes the hot pressure past where the tire grips well. 

## How much pressure a tire gains from heat 

Tire pressure rises during track sessions because the carcass and tread heat up, and heated air expands inside the tire. A tire worked hard on track can gain several psi over its cold figure, and the exact rise depends on the tire, the car and the session length. The gain is a clue about how hard the tire is working. 

Measure hot pressure within a few minutes of coming into the pits, before the tire cools. A large gain suggests the tire is running hot, while a small gain shows the tire stays cool. Compare the gain across all four tires to spot which corner carries the load. 

Tire temperature and psi move together, so a pressure reading without a temperature note is incomplete. Infrared pyrometers and probe gauges measure tread and carcass heat, but use them as a guide rather than a precise target. Some drivers find the pressure settles once the tire reaches its working range. 

## Using hot readings to adjust for the next session 

Hot pressure readings tell you what the tire actually reached, so adjust from those numbers rather than from the cold settings. If the hot psi climbs above the target range, lower the cold pressure a little before the next session. If the tire stays soft when hot, raise the cold pressure in small steps. 

Change the cold pressure by small increments and record the result, because a big jump hides the effect of the change. Bleeding air from a hot tire lowers the pressure now, but the cold figure drops too, so plan the next cold setting. Some drivers bleed the tire after each session to reach the hot target, then reset cold for the morning. 

Recheck the pressures before every session and after the last run, and adjust for weather and track temperature. A cool morning can give lower cold readings than a warm afternoon on the same tire. Keep the cold and hot numbers side by side so the pattern across sessions stays visible. 
| Reading | When taken | What it tells you | 
| Cold psi | Before the first session, tire at ambient | The base setting for the day | 
| Hot psi | Minutes after coming off track | What the tire reached under load | 
| Pressure gain | Hot minus cold | How hard the tire worked and how hot it ran |  

## Cold and hot pressure differ on every tire 

Cold tire pressure and hot tire pressure are two different measurements of the same tire, and the gap between them depends on the tire construction. A stiff sidewall with a low profile may gain less than a soft tire worked hard. Note the gain for your own tire and refit it to the cold target. 

Brand-specific track pressures exist because each tire maker builds its sidewall and tread to suit a pressure window. Pirelli track day tire pressure guidance, for example, comes from that maker's own testing and should be followed over a rule of thumb. Follow the pressure range from the tire you own, not the one from a different brand or model. 

A track day tyre pressures check written in metric units uses the same logic, with bar instead of psi. Convert carefully if your gauge reads in bar, and record the unit on every entry. Pressure gauges can be graded in psi or bar, so confirm the scale before you inflate. 

## How car setup and track temperature change the target 

Track car tire pressure responds to the weight, the alignment and the driving style, so two cars on the same tire can need different figures. A heavier car with aggressive camber builds heat faster in the inner shoulder and pushes the pressure higher. Soft springs and body roll load the outside tire harder and raise its temperature. 

Track surface temperature changes the pressure gain from one run to the next, and the same cold setting gives a different hot figure in cool air. Tire pressure gain under heat is larger on a hot track, so a setting that works in the morning may overinflate by afternoon. Adjust the cold setting to the conditions of each session. 

Tire size and profile affect how much pressure the sidewall carries, and a change of wheel width changes the contact patch. Keep the same tire and wheel combination while you tune pressure, or the readings lose their value. Fitting a wider tire or a different wheel width means starting the pressure search again. 

## Small steps, records and safety 

Make one pressure change at a time and give the tire a full session to respond before deciding the next step. A single adjustment of a few psi is enough to notice a grip or wear change, and larger jumps blur the result. Record the cold setting, the hot reading, the tire and the session so the history stays useful. 

Check pressure when the tires are cool, and never handle a hot tire with bare hands or lean over a wheel while it is being inflated. Overinflation can damage a tire and the rim, so stay within the maximum cold pressure on the sidewall. A trained specialist should mount and inspect track tires and rims. 

Retire a tire that shows cracks, bulges or cord, and check the valve and rim seal for leaks before each event. The pressure reading is only one part of tire condition, and visual checks catch damage the gauge cannot show. Safe track driving starts with sound tires and correct pressures before the first lap. 

## Track Day Tire Pressure Questions 

### What is a good track day tire pressure? 

A good track day tire pressure is the figure your tire maker or car manual gives for track use, set cold before the first session. The target depends on the tire brand, the car and the track temperature, so no single psi fits every car. Aim for a hot pressure range you can repeat and log the gains. 

### Should I set cold tire pressure before or after the first session? 

Set cold tire pressure before the first session, while the tires sit at ambient temperature. Measure the cold pressure in the morning, then check hot pressure minutes after each run to see the gain. Resetting pressure after the tire cools gives a cleaner cold figure for the next day. 

### How much does track day tire psi increase when hot? 

Track day tire psi increases during a session because the tire carcass and tread heat up and the air inside expands. The exact rise depends on the tire, the car and the track, so measure the hot figure right after you come in. The difference between cold and hot tells you how hard the tire worked. 

### What are Pirelli track day tire pressures? 

Pirelli track day tire pressures come from the tire maker's own guidance for that model, so follow the figures Pirelli publishes for your tire. The cold setting should leave room for the pressure gain during a session. Confirm the size and the maximum cold pressure on the sidewall before inflating. 

### Does tire temperature and PSI tell me whether the setup is right? 

Tire temperature and pressure together show how hard each corner works, because heat drives the pressure rise. A tire that climbs far above its target may be overinflated or overloaded, so check both figures after a session. Use a pyrometer for tread and carcass heat and a gauge for pressure. 

### Can I bleed air from hot tires at the track? 

Bleeding air from hot tires lowers the pressure for the next session, but the cold figure will also drop, so record both numbers. Release only a small amount and check again with the same gauge. Plan the next cold setting so the hot pressure lands in the range you want.
