# Tire Size Overlay Comparison

A tire size overlay comparison shows two tire outlines drawn to the same scale, so you can see how diameter, width and sidewall height differ before you buy.

A tire size overlay comparison draws two tire outlines at the same scale so their differences are visible at a glance. One size sits inside or beside the other, and you can read how overall diameter, section width and sidewall height change from one to the next. The overlay turns sidewall numbers into a picture you can judge against your vehicle. 

- An overlay puts two tire outlines on one shared scale, so the eye compares them directly.
- Overall diameter, section width and sidewall height are the three dimensions that drive the picture.
- Sidewall numbers must be decoded into millimeters before any outline can be drawn accurately.
- A diameter change shifts the axle height and the speed reading, so check clearance before you commit.
- An overlay does not show tread behavior, load rating or wheel width fit, which you must check separately.
 

## What a tire size overlay shows you 

A tire size overlay is a scale drawing that places the outline of one tire against another tire for direct visual comparison. The two circles share a center line, so width and height differences read immediately. This visual tire size overlay removes guesswork from a row of sidewall figures. 

The overlay comparison answers a simple question: how much bigger or smaller is the new size than the one already on the car. A scaled outline comparison keeps both tires proportional, so a taller sidewall looks taller next to a shorter one. The picture is a geometry tool, not a performance rating. 

A tire size overlay diagram shows the beaded tire on a nominal rim, with the sidewall and tread width drawn together. Space between the two outlines marks the change in each direction. Reading that gap tells you whether the change is modest or large. 

## Decoding the sidewall numbers first 

Sidewall numbers give the three inputs every overlay needs: section width, aspect ratio and rim diameter. A marking such as 225/45R17 states width in millimeters, then sidewall height as a percentage of that width. The letter R means radial construction and the last number is the wheel diameter in inches. 

The sidewall height is not printed directly on the tire. Multiply the section width by the aspect ratio to get the sidewall height of one side, so a 225 mm width at 45 percent yields about 101 mm. Add that twice to the rim diameter in millimeters to reach overall diameter. 

Sidewall dimensions mix units, which is why converting before drawing matters. Rim size arrives in inches and section width in millimeters, so a single unit system keeps the overlay honest. An overlay tool that skips the conversion shows a distorted outline. 

## How to compare two sizes side by side 

A side-by-side size comparison works best when you set one size as the reference and change one number at a time. Hold the rim diameter fixed first, then vary [width and aspect ratio](/articles/comparing-tire-width-and-aspect-ratio/) to see each effect separately. Comparing everything at once hides which change causes which shift. 

Step through the numbers in a fixed order so the overlay stays readable. Note the reference size, list the candidate size, then convert both to the same units before you draw. The three dimensions follow from the sidewall marks, and the outline is the result. 

A side-by-side tire diagram rewards a patient approach. Change width alone and the aspect ratio still governs the height, so a wider tire at the same ratio grows taller too. The overlay shows both effects at once when you keep the reference in place. 

## Reading diameter, width and sidewall height 

Overall diameter sets how tall the tire stands and therefore how far the wheel axis sits from the ground. A larger tire diameter raises the vehicle slightly and turns fewer times over the same distance. The diameter overlay comparison shows the height difference as the gap between the top edges. 

Tire width, or section width, is the widest point of the inflated tire at the sidewall, not the tread face. A wider tire needs a rim within its recommended range, and the extra width can reach suspension parts or the fender liner. The overlay shows width as a horizontal change between the two outlines. 

Sidewall height is the visible band between rim and tread, and the aspect ratio sets it. A taller sidewall softens the visual look and changes ride feel, while a shorter one draws that band tight. The overlay makes the band thickness easy to compare between two sizes. 

## What the overlay changes in diameter do 

Tire diameter changes touch the speedometer and the gearing, because the wheel covers more or less ground per turn. A taller tire reads lower on the speedometer than the real speed, so the display drops below actual road speed. The overlay does not calibrate anything, but it warns you how much the diameter moves. 

Fender and suspension clearance is the other consequence of a larger diameter. Check clearance at full steering lock and under compression before fitting a taller tire. A drawing cannot show the suspension travel, so trust a physical check for the final answer. 

A diameter change of only a small fraction keeps the speedometer close to its original reading. Larger shifts call for a recalibration or a correction device, and the overlay helps you judge whether the change is small. Match the diameter rather than the rim size when you want the original reading. 

## Where width and aspect ratio change the look 

Width and aspect ratio together drive what the tire looks like on the car, and an overlay shows that width and aspect ratio look directly. A wider section gives a squarer shoulder and a broader footprint, while aspect ratio controls the sidewall band. The same width with a lower ratio pulls the tire closer to the rim. 

The tire footprint overlay shows the contact patch as a rectangle under each outline. A wider section usually widens that patch, though inflation pressure and wheel width also matter. Do not read grip from the patch shape alone, because the compound and tread decide traction. 

A tire size overlay on a vehicle outline adds context that a bare tire picture lacks. Place the scaled outline against the wheel arch and you see how much sidewall shows above the rim. The rim edge and the fender gap together tell you whether the look stays proportionate. 

## Limits of a two-dimensional outline 

A tire dimension overlay comparison is a side view, so it cannot show the tread pattern or the shoulder shape in three dimensions. The overlay of tire outlines treats the tire as a simple ring with a width, which is close but not exact. Rounded shoulders and tread blocks change the real profile. 

An overlay does not show load index, speed rating, or the wheel width range the tire maker lists. Those details sit in the full tire specification and are separate from the geometry. Confirm them with the tire maker and the vehicle placard before fitting. 

The drawing also ignores how the tire deforms under load and how the vehicle sits at rest. A real tire flattens slightly at the contact patch, which trims a small amount from the rolling radius. Use the overlay for comparison, then confirm fitment with a trained tire technician. 

## Using an overlay chart for a decision 

A tire size overlay chart collects several candidate sizes on one common scale instead of two at a time. Reading the chart as a whole shows which candidate stays closest to the reference outline. Size variation comparison becomes a visual filter rather than a spreadsheet chore. 

Set your goal before you open the chart, because the overlay rewards a clear target. Matching diameter, gaining width, or keeping sidewall height each lead to a different row. Mark the reference and read backwards from the goal. 

Once the overlay narrows the list, take the remaining candidates to a fitting check. A tire technician can test clearance and confirm the [rim width range](/articles/approved-rim-widths-by-tire-size-checking-tire-and-rim-compatibility/) on the vehicle. The overlay diagram is the starting picture, and the physical fit confirms it. 

## Tire Size Overlay Questions 

### What is a tire size overlay comparison? 

A tire size overlay comparison is a scale drawing that puts two tire outlines together so their dimensions can be compared. It shows overall diameter, section width and sidewall height as visible differences. The tool uses sidewall numbers as its input, not measurements taken from the car. 

### How do I compare two tire sizes side by side? 

Set one size as the reference and change a single number in the second size at each step. Convert both sizes into the same unit system before drawing the outlines. Then read the diameter difference at the top edge and the width difference at the sidewall. 

### What does a tire diameter overlay show that a number does not? 

A tire diameter overlay shows the relative difference between two overall diameters as a gap between outlines. The number states the change in millimeters or inches, while the overlay shows the change against the whole tire. The visual comparison helps you judge whether a change is small or large. 

### Can a tire size overlay show how the tire looks on my vehicle? 

A sidewall size overlay on a vehicle outline can place the scaled tire against the wheel arch. That picture shows how much sidewall sits above the rim and how the diameter fills the arch. Fender clearance and suspension travel still need a physical check on the car. 

### Does the overlay account for wheel width and load rating? 

No, a tire size overlay covers geometric dimensions only and does not check wheel width or load rating. The tire maker lists the recommended rim widths and the load and speed ratings separately. Confirm those figures with the maker and the vehicle placard before fitting. 

### Why do tire size variations look different from the numbers alone? 

Tire size variations look different because width and aspect ratio change together, and each affects height and shoulder shape. A wider tire at the same aspect ratio grows taller, which a row of numbers does not show directly. The overlay makes those combined effects visible in one outline.
