# Tire Size Conversion and Comparison Explained

Learn how to read sidewall numbers, convert metric tire sizes to inches, and compare overall diameter, section width, and rim diameter side by side.

Tire size conversion and comparison starts with the characters printed on the sidewall, which describe the tire's width, height ratio, and the wheel it fits. Converting those metric figures to inches lets you compare one tire against another before you buy or change wheels. The work is arithmetic on the sidewall markings, not guesswork. 

- The sidewall code gives section width in millimeters, aspect ratio as a percentage, and rim diameter in inches.
- Overall diameter equals the rim diameter plus twice the sidewall height, and sidewall height is width times aspect ratio.
- [Load index and speed rating](/articles/tire-load-index-load-range-speed-ratings-material-44528/) describe capacity and speed capability, and both belong in a comparison.
- A side-by-side comparison checks diameter, width, and wheel fitment before any swap.
- Changing overall diameter affects speedometer reading and clearance, so verify before fitting.
 

## Reading the numbers on the sidewall 

A tire sidewall carries a code such as 225/45R17, and each part of that code has a fixed meaning. The first number is the section width in millimeters, measured across the widest part of the inflated tire. The second number is the aspect ratio, the sidewall height expressed as a percentage of the section width. 

The letter after the slash shows the internal construction, where R means radial and other letters mark older designs. The number after the letter is the rim diameter in inches, the wheel size the tire mounts on. A separate block gives the load index and the speed rating, which describe how much weight the tire carries and how fast it may run. 

Load index is a code that maps to a maximum load per tire, and speed rating is a letter that maps to a maximum speed. Both values must meet or exceed what the vehicle manufacturer specifies for the axle. Ignoring them makes a size comparison incomplete, even when the three main numbers match. 

## How to convert metric sizes to inches 

Metric to inch conversion for tires turns the millimeter width into inches and builds the overall diameter from there. Divide the section width by 25.4, the number of millimeters in one inch, to get the width in inches. That single step makes the metric figure comparable with inch-based tire and wheel measurements. 

Sidewall height in inches comes from multiplying the section width in millimeters by the aspect ratio, then dividing by 100 to get millimeters, then dividing by 25.4. Multiply that sidewall height by two and add the rim diameter to reach the overall diameter. The result is the tire's standing height, the figure that matters for clearance and gearing. 

Worked on 225/45R17, the width is about 8.86 inches and the sidewall height is about 3.99 inches. Doubling the sidewall gives about 7.98 inches, and adding the 17-inch rim gives an overall diameter near 24.98 inches. Keep the intermediate figures unrounded until the end so small errors do not multiply. 

- Convert width: divide the millimeter section width by 25.4.
- Find sidewall height: width in millimeters times aspect ratio, divided by 100.
- Convert sidewall height to inches: divide by 25.4.
- Double the sidewall height and add the rim diameter.
- Compare the result with the original tire's overall diameter.
 

## What each dimension changes on the vehicle 

Overall diameter sets how tall the tire stands, and that height changes the speedometer reading and the effective gearing. A larger diameter makes the wheel turn slower at a given road speed, so the indicated speed drifts from the real speed. Clearance inside the wheel well and against suspension parts also depends on this figure. 

Section width affects how far the tire extends outward from the hub and how much room it needs inside the arch. A wider section can rub on the inner liner or the suspension at full steering lock. Aspect ratio controls the sidewall depth, which trades ride softness against steering response. 

Rim diameter must match the wheel exactly, because a tire only seats and seals on the rim size it was built for. Mounting a tire on a rim of the wrong diameter is dangerous and can damage both parts. Check rim width against the tire maker's approved range as well, since section width alone does not confirm fitment. 

## Comparing two sizes side by side 

A side-by-side size comparison lines up the old and new tire on width, sidewall height, overall diameter, and rim diameter. Converting both to inches puts them on the same scale and shows differences directly. The comparison reveals whether a swap stays within tolerance or shifts the tire noticeably. 

Small differences in overall diameter are absorbed by normal tread wear, and larger ones change the speedometer and clearance in ways you can measure. Width differences matter most at the inner and outer edges, where contact with bodywork happens. Record each figure before deciding, rather than judging by eye. 

The table below compares two sizes using the conversion method, with numbers rounded for reading. Use it as a pattern for any pair of sizes, and keep load index and speed rating in the check. 
| Dimension | 225/45R17 | 235/40R18 | 
| Section width | 8.86 in | 9.25 in | 
| Sidewall height | 3.99 in | 3.70 in | 
| Overall diameter | 24.98 in | 25.40 in | 
| Rim diameter | 17 in | 18 in |  

## Matching load index and speed rating 

Load index and speed rating are part of the size, not optional extras, and a correct comparison includes them. Two tires of the same physical size can carry different loads and have different speed limits. The vehicle's placard states the minimum values for each axle position. 

A lower load index reduces the weight the tire may carry, which matters on a loaded vehicle or a trailer. A lower speed rating reduces the maximum speed the tire sustains under load. Choosing below the placard figure is a safety decision, not a styling one. 

When you convert to a different size, confirm the new tire meets or exceeds both values from the placard. Record both codes next to the dimensions in your comparison so nothing is overlooked. A tire shop or the vehicle manufacturer can confirm the correct figures for your setup. 

## Checking wheel width and clearance 

Wheel width is a separate measurement from rim diameter, and the tire maker publishes an approved range of rim widths for each size. A section width that fits the diameter may still sit poorly on a narrow or wide rim. Fitment depends on both figures together, not on the tire code alone. 

Clearance checks cover the wheel well, the suspension strut, the brake caliper, and the inner fender liner. Turn the steering to full lock and inspect the gap at the tire's widest point. A change in overall diameter also alters the gap at the top of the arch. 

A trained technician should perform any mounting, balancing, and clearance inspection on a modified vehicle. Tire work under a loaded vehicle or with altered suspension carries injury and damage risk. Have the final fitment checked before driving on the new setup. 

## When a size conversion is worth doing 

A size conversion makes sense when the original size is unavailable or when a wheel change requires a different code. The goal is to keep overall diameter close to the original while meeting load index and speed rating. Every other dimension follows from that target. 

Compare the converted figures against the placard and against the physical space around the tire. Note how each dimension changes and whether the change stays inside the tolerance you can accept. A conversion that moves the diameter far from the original changes the speedometer and gearing. 

Write the comparison down and keep the original sidewall code with it for reference. Confirm the load index and speed rating on the new tire before purchase. A specialist can verify the arithmetic and the fitment when the vehicle is modified. 

## Tire Size Conversion Questions 

### What does tire size conversion and comparison mean? 

Tire size conversion and comparison means translating the sidewall code into inches and lining up two tires on the same dimensions. The conversion covers section width, sidewall height, and overall diameter, while the comparison checks how they differ. Load index and speed rating complete the picture. 

### How do I convert a metric tire size to inches? 

Divide the section width in millimeters by 25.4 to get width in inches for the metric to inch conversion. Multiply the width by the aspect ratio and divide by 100 for sidewall height in millimeters, then divide by 25.4. Double that height and add the rim diameter to get overall diameter. 

### What is the difference between section width and overall diameter? 

Section width is the tire's width across its widest point, while overall diameter is its standing height from tread to tread. Section width sets how far the tire extends sideways, and overall diameter sets the rolling height. Both appear in a side-by-side size comparison. 

### Do load index and speed rating matter in a size comparison? 

Yes, load index and speed rating belong in every [tire size comparison](/articles/tire-size-calculator-diameter-comparison-material-44527/) because they set weight capacity and speed capability. Two tires of the same size can differ on both codes. The vehicle placard states the minimum values to match or exceed. 

### Can I change tire size without changing the wheel? 

You can change tire size without changing the wheel only if the new tire fits the existing rim diameter and approved [rim width range](/articles/approved-rim-widths-by-tire-size-checking-tire-and-rim-compatibility/). Overall diameter and section width also need to clear the vehicle. A trained technician should confirm fitment before mounting. 

### Why does overall diameter matter when comparing sizes? 

Overall diameter matters because it changes the speedometer reading, the effective gearing, and the clearance around the tire. A diameter far from the original alters how the vehicle behaves on the road. Compare it against the original size before any swap.
