Tire Dimension Chart in Inches

Learn to read a tire dimension chart in inches. Convert metric sidewall numbers to section width, sidewall height and overall diameter, and compare sizes.

9 min read1 views
— · 0 votes
Contents
  1. What a tire dimension chart shows
  2. Reading the sidewall numbers in order
  3. Converting millimeters to inches
  4. Working out sidewall height and overall diameter
  5. Building a comparison table for two sizes
  6. Matching width and rim diameter to the wheel
  7. Why nominal sizes differ from measured tires
  8. Tire Dimension Chart Questions
  9. How do I read a tire dimension chart in inches?
  10. What does the aspect ratio tell me in inches?
  11. How is overall diameter calculated from tire size?
  12. Is tire width in inches the same as section width?
  13. Can I compare two tire sizes with a width and height chart?
  14. Does the rim diameter in the code need conversion?

A tire dimension chart in inches converts the metric code on a sidewall into section width, sidewall height and overall diameter measured in inches. The first number gives the width in millimeters, the aspect ratio gives sidewall height as a share of that width, and the rim diameter is already in inches. Read together, those three values describe the size of the tire without any measuring tool.

  • The first sidewall number is section width in millimeters, so divide by 25.4 to get width in inches.
  • Aspect ratio is a percentage of section width, not a fixed height, so the same ratio means different sidewall heights on different widths.
  • Overall diameter equals the rim diameter plus two sidewall heights, all in inches.
  • A tire dimension table lets you compare two sizes by width, height and diameter before you change anything on the vehicle.
  • Rim diameter matches the wheel, and a tire must fit the rim it is mounted on.

What a tire dimension chart shows

A tire dimension chart lines up the numbers molded into a sidewall with the physical measurements they stand for. The code holds three values: a width in millimeters, an aspect ratio with no unit, and a rim diameter in inches. The chart turns that mix of units into one consistent set of inch figures.

Tire measurements in a chart cover section width, sidewall height, overall diameter and rim diameter. Section width is the widest point of the inflated tire, measured across the sidewalls. Sidewall height is the distance from the rim edge to the tread, and overall diameter is the full height of the tire from tread top to tread top.

A tire size measurement chart is a planning aid, not a tape measure. Published figures describe a nominal size, and real tires vary a little between builders and tread patterns. Use the chart to understand the code and to compare sizes, then confirm the actual figure with the tire maker when a tight clearance matters.

Code partWhat it statesUnit on the sidewallInch conversion
First numberSection widthMillimetersDivide by 25.4
Second numberAspect ratioPercentage, no unitUsed in the height formula
Letter RRadial constructionNoneNot a size value
Last numberRim diameterInchesAlready in inches

Reading the sidewall numbers in order

Sidewall numbers read left to right, and the order never changes on a metric passenger tire code. A size such as 225/45R17 starts with 225, the section width in millimeters. The 45 is the aspect ratio, the R marks radial construction, and 17 is the rim diameter in inches.

The aspect ratio is a percentage of the section width, so it is a ratio rather than a length. On a 225 mm wide tire, an aspect ratio of 45 gives a sidewall height of about 101 mm. A wider tire with the same ratio carries a taller sidewall, which is why a ratio alone says nothing about height in inches.

The letter between the ratio and the rim figure describes the internal construction of the tire. Radial tires carry an R, and older bias-ply designs used a D. A code may also show a load index and a speed symbol after the rim figure, and those markings are not part of the dimensional size.

Converting millimeters to inches

Metric to inch conversion for a tire relies on one fixed factor, because one inch equals 25.4 millimeters. Section width in inches comes from dividing the millimeter width by 25.4. A 225 mm section width works out to roughly 8.86 inches, and a 275 mm width to about 10.83 inches.

The conversion matters because tire codes mix millimeters and inches in the same string. Width arrives in millimeters, while rim diameter is already given in inches. A tire size to inches conversion puts both values in the same unit so a width and diameter chart stays coherent.

Inches and millimeters both appear on dimension tables, and rounding differs between them. A chart may round 8.86 inches to 8.9, which is fine for reading a table but drifts when used in further math. Keep the unrounded figure for any clearance check and round only when you present the result.

Working out sidewall height and overall diameter

Sidewall height in inches follows from the width and the aspect ratio, with one extra conversion step. Multiply the section width in millimeters by the aspect ratio as a decimal, then divide by 25.4. For 225/45R17, that gives 225 times 0.45, then divided by 25.4, or about 1.99 inches.

Overall diameter in inches adds the rim diameter to two sidewall heights, because the tire has a sidewall above and below the wheel. The 225/45R17 example gives 1.99 inches twice plus 17 inches, for an overall diameter of roughly 21 inches. The tire diameter in inches is the figure that decides fit in the wheel well.

The overall diameter chart is where planning pays off. A taller overall diameter lifts the vehicle slightly and changes how far the tire travels per turn of the wheel. A shorter one lowers the vehicle and raises the number of turns for the same distance. Neither change is free, so compare the figures before deciding.

Building a comparison table for two sizes

A width and height table lets you place two candidate sizes side by side and read the differences at a glance. List section width, sidewall height, rim diameter and overall diameter as rows, then fill one column per size. The comparison shows whether the new tire grows in width, in height or in both.

Width and diameter do not move together, and the aspect ratio controls the link. Going up in width at the same ratio adds sidewall height and therefore overall diameter. Dropping the ratio when you add width can hold overall diameter close to the original figure, which keeps the speed reading and clearances nearer to stock.

A tire chart comparison to inches only works when both sizes are converted to the same unit first. Put the metric widths into inches before you compare, then check overall diameter against the original fitment. Differences in width affect clearance to suspension and bodywork, while differences in diameter affect gearing and the wheel well.

Matching width and rim diameter to the wheel

Rim diameter in the tire code must match the wheel exactly, and no conversion changes that. A tire marked for a 17 inch wheel fits a 17 inch rim and nothing else. Width is more flexible, because a given section width sits within a range of rim widths set by the tire maker.

Section width inches describe the tire, while rim width describes the wheel, and the two are separate figures. A tire mounted on a rim at the narrow end of its range sits differently from the same tire on a wider rim. The tire maker publishes the approved rim widths for each size, and that list is the authority.

A chart cannot confirm that a wheel and tire combination clears the brakes, the suspension or the body. Measuring the space around the current tire and checking the maker's rim range are separate steps. A trained tire technician should confirm any fitment that changes width or diameter before the vehicle goes on the road.

  • Read the rim diameter from the sidewall and match it to the wheel exactly.
  • Convert section width to inches before comparing with the rim width range.
  • Check the tire maker's approved rim widths for the exact size.
  • Confirm brake and suspension clearance with the wheel fitted.
  • Have a trained technician verify any change in width or overall diameter.

Why nominal sizes differ from measured tires

A nominal size is the figure the maker assigns to a tire, and it is not a promise of exact physical dimensions. Two tires with the same code can measure differently once mounted and inflated. Tread pattern, internal construction and the rim width all shift the real figures.

Tire dimension charts therefore show nominal values, which are consistent enough for planning and comparison. Section width on a narrow rim can come out below the nominal figure, and the same tire on a wide rim can come out above it. Overall diameter moves less, but it still depends on tread depth and inflation.

Read a chart as a map of the sizing system rather than a measurement record. When a clearance is tight, the numbers on the chart narrow the choices, and the maker's published dimensions settle the rest. Physical measurement of the mounted tire is the final check before any tight fitment is accepted.

Tire Dimension Chart Questions

How do I read a tire dimension chart in inches?

A tire dimension chart in inches converts the sidewall code into inch figures for width, sidewall height and overall diameter. Find the section width in millimeters, divide by 25.4, then use the aspect ratio for sidewall height and add the rim diameter for overall diameter. The chart simply presents those three results in one place.

What does the aspect ratio tell me in inches?

The aspect ratio is a percentage of section width, not a measurement in inches on its own. Multiply the width in millimeters by the ratio as a decimal, then divide by 25.4 to get sidewall height in inches. A 45 series on a 225 mm tire gives a sidewall of about 1.99 inches.

How is overall diameter calculated from tire size?

Overall diameter equals the rim diameter plus two sidewall heights. Work out one sidewall height in inches from the width and aspect ratio, double it, and add the rim diameter, which is already in inches. The result is the tire diameter in inches used for clearance and gearing checks.

Is tire width in inches the same as section width?

Yes, tire width in inches is the section width converted from millimeters. Section width is the widest point across the inflated tire, and it appears on the sidewall in millimeters. Divide that number by 25.4 to express it in inches.

Can I compare two tire sizes with a width and height chart?

A width and height chart compares two tire sizes by section width, sidewall height and overall diameter. Convert both sizes to inches first, then read the differences row by row. The comparison shows how much the tire grows or shrinks in each direction.

Does the rim diameter in the code need conversion?

No, rim diameter in a tire code is already stated in inches. The figure after the construction letter, such as 17, matches a 17 inch wheel directly. Only the section width needs metric to inch conversion, which is why a dimension table mixes both units.

Latest articles