# Tire Air Pressure Chart by Tire Size (Metric)

How a metric tire size points to a starting inflation pressure, what the sidewall limit means, and why the vehicle placard, not the size alone, sets the PSI.

A tire air pressure chart by tire size cannot give one exact PSI for each metric size, because the correct inflation pressure comes from the load the tire must carry on a specific vehicle. The metric size tells you the tire's dimensions and load index, and that load index links to a pressure table. The vehicle placard gives the pressure you should actually run, and the sidewall only states a maximum. 

- Read the metric size first: width, aspect ratio, wheel diameter, [load index and speed symbol](/articles/tire-load-index-load-range-speed-ratings-material-44528/).
- The load index pairs with a pressure table to show how much weight the tire carries at a given PSI.
- The sidewall number is a maximum pressure, not a recommendation for your car.
- Use the vehicle placard for daily inflation and adjust for heavy loads as the manufacturer states.
- A chart can confirm a fitment, but it cannot replace the placard or a trained tire specialist.
 

## What a metric tire size encodes 

A metric tire size such as 225/45R17 packs four facts into one string. The first number is the nominal section width in millimeters, and the second is the aspect ratio, a percentage of that width that gives the sidewall height. The letter R means radial construction, and the last number is the wheel diameter in inches. 

After the size come the service description numbers, which carry the load index and the speed symbol. The load index is a code for the maximum load the tire can carry at its rated pressure. That code, not the width or the diameter, is the bridge between a metric size and an inflation pressure chart. 

Sidewall numbers also include a maximum pressure marking, which states the highest cold inflation the tire is built to hold. Two tires of the same size can carry different load indexes, so a chart keyed only on 225/45R17 would miss the difference. Always match the full service description before you trust a pressure figure. 

## Why pressure charts are built on load, not size 

A tire pressure chart by size works because each load index maps to a load and inflation table. The table shows how much weight a tire carries at a series of cold pressures. A higher pressure within the tire's rating lets the same tire carry more load, up to its maximum. 

The metric size sets the volume and shape of the tire, and the load index sets its capacity. Pressure is the link between them. A chart that shows recommended PSI by tire size is really showing the pressure needed to carry a load, with the size as the label. 

This is why a side by side tire pressure chart compares load indexes rather than widths. Reading two sizes across the same row tells you which tire needs more pressure for the same load. The chart answers a load question, and the size alone cannot. 

## The placard outranks any size chart 

The vehicle placard gives the recommended inflation pressure for the tires fitted to that car. It sits on the driver door jamb, the fuel filler door or inside the glovebox, and it lists front and rear pressures for the original size. The placard is the figure the manufacturer validated for the car's weight and handling. 

A pressure chart by tire size can support the placard when you change to a different size with a different load index. In that case the chart tells you the pressure that carries the same load as the original. A trained tire specialist should confirm any size change that alters the load index or the overall diameter. 

Never inflate to the sidewall pressure limit as a daily setting. That number is a ceiling for the tire, not a target for the car. Filling to the maximum leaves no margin for heat buildup and can change how the tire wears and grips. 

## Reading a metric pressure table 

A metric pressure table lists load index down one side and cold inflation pressure across the top. Each cell holds the load the tire can carry at that pressure. To use it, find your load index, then read across to the pressure that meets or exceeds the load your axle carries. 

Convert the vehicle's axle load to a per-tire figure by dividing by two for a normal axle. Compare that figure with the table entry and pick the pressure that covers it. The placard pressure for the original tire is the simplest reference, since the manufacturer already did this math. 

Pressures in these tables are cold pressures, measured before the tire has warmed from driving. A warm tire reads higher, so never bleed air from a hot tire to match a cold chart figure. Check and set pressure when the tire is at ambient temperature. 

## Sidewall limit versus recommended pressure 

The sidewall pressure limit is the highest cold pressure the tire is designed to hold, and it appears next to the maximum load. Recommended inflation pressure is a different number, set by the vehicle maker for ride, wear and load. Confusing the two is a frequent fitment error. 

A tire rated to a high maximum pressure does not need that pressure in a light car. Running at the sidewall limit on a vehicle that calls for less reduces the contact patch and can wear the center of the tread. The recommended PSI by tire size should always be read alongside the vehicle requirement. 

When you fit a tire with a higher load index than the original, the chart may call for a lower pressure to carry the same load. That lower figure still needs to stay within the range the vehicle maker specifies. A specialist can reconcile the two figures for your setup. 

## Using a size calculator with care 

A tire air pressure chart by size calculator takes the metric size, load index and axle load and returns a suggested cold pressure. These tools are useful for comparing sizes and for checking that a new tire carries the load at a sensible pressure. They are only as good as the load data you enter. 

Enter the actual axle load from a scale or the vehicle's rated figures, not a guess. Use the full service description, since a calculator keyed on size alone may pick the wrong load index row. Check the result against the placard and the sidewall limit before you inflate. 

A calculator cannot see tread wear, alignment or the car's handling balance. Treat its output as a starting figure for comparison, and confirm any change with a trained technician. The final authority remains the vehicle placard and the tire's rated limits. 

## Pressures for load, towing and heat 

Load changes the pressure a tire needs, and the placard often lists a higher rear pressure for a fully loaded car. Follow that two-stage guidance when you carry passengers or cargo. The metric chart shows the same effect: more load needs more pressure, up to the tire's rating. 

Heat builds in an underinflated tire and raises the risk of damage, especially at highway speed with a heavy load. A pressure that suits an empty car can be too low for a loaded one. Check pressure before a trip and adjust to the loaded figure the manufacturer gives. 

Do not exceed the sidewall limit when you raise pressure for load. If the load you plan needs a pressure above the tire's maximum, the tire is not rated for that job. Choose a tire with a higher load index or reduce the load, and let a specialist advise. 

## When a chart is not enough 

A pressure chart cannot account for a changed wheel diameter, a different aspect ratio or a modified suspension. These changes affect clearance, speedometer accuracy and load distribution. A fitment check belongs with a trained tire specialist before you commit to a size. 

Mixing load indexes across an axle, or fitting a tire whose maximum pressure is below the vehicle requirement, creates risk that no chart resolves. Keep all four tires matched in size, load index and construction unless the vehicle maker states otherwise. Ask a professional when the numbers do not line up. 

Chart reading is a skill of comparison, not a substitute for inspection. Physical checks for damage, tread depth and sidewall condition still matter. Use the chart to understand the numbers, and use a specialist to confirm the fit. 

## Tire pressure chart questions 

### Is there a tire air pressure chart by size calculator I can trust? 

A calculator is useful as a comparison tool, but it is not the final authority. It needs the load index and the actual axle load to return a sensible cold pressure. Treat its result as a starting figure and confirm it against the vehicle placard and the sidewall limit. 

### What does a side by side tire pressure chart show? 

A side by side tire pressure chart compares two or more sizes or load indexes at the same pressures. It shows which tire carries more load at a given PSI or which pressure each needs for the same load. The comparison only works when the load index is included. 

### Can I set my tires to the pressure on the sidewall? 

No, the sidewall number is the maximum cold pressure the tire is built to hold. Recommended inflation pressure comes from the vehicle placard for your car and load. Inflating to the sidewall limit as a daily setting can change wear and handling. 

### How do I find recommended PSI by tire size? 

Start with the vehicle placard, which lists pressures for the original size. If you change to a different load index, use a load and inflation table to find the pressure that carries the same load. A tire specialist can confirm the figure for your setup. 

### Why do two tires of the same metric size need different pressures? 

The metric size fixes width, aspect ratio and wheel diameter, but the load index can differ. A higher load index tire carries more weight at the same pressure, so it may need less pressure for a given load. The service description, not the size alone, drives the pressure. 

### Should I check pressure when the tire is warm? 

Check and set pressure when the tire is cold, before driving has warmed it. A warm tire reads higher than its cold pressure, so bleeding air to match a cold chart figure leaves it underinflated. Use a cold reading as your reference.
