Rolling Resistance Modeling: How the Model Is Built

Learn how a rolling resistance model is built from tire deformation, hysteresis, load and speed, using the rolling resistance equation, inputs and assumptions.

7 min read3 viewsRolling Resistance Modeling: How the Model Is Built
— · 0 votes
Contents
  1. What a rolling resistance model describes
  2. Hysteresis losses inside the tire
  3. The rolling resistance force equation
  4. How load changes the resistance
  5. Speed dependence in the model
  6. Inputs and assumptions a model needs
  7. Steps to build the model
  8. Reading a model's results correctly
  9. Rolling resistance modeling questions
  10. What is a rolling resistance model?
  11. How do you calculate rolling resistance force?
  12. What is the rolling resistance coefficient Crr?
  13. How do load and speed affect rolling resistance?
  14. What inputs does a tire rolling model need?
  15. Why does a model need assumptions?

A rolling resistance model is built by turning the energy a tire loses as it deforms into a force that acts against forward motion. The model combines the normal load, the rolling resistance coefficient, and the speed dependence observed in testing. Each part is described by an equation, then fitted with measured inputs and clear assumptions.

  • Rolling resistance force comes from energy lost in the tire as it deflects and recovers.
  • The rolling resistance coefficient Crr links the resistance force to the normal load.
  • Hysteresis losses in the rubber are the main reason a rolling tire loses energy.
  • Load and speed effects change the resistance, so a model states how it treats each.
  • A model is only as good as its inputs and the assumptions written beside them.

What a rolling resistance model describes

A rolling resistance model describes the force that opposes a tire as it rolls on a surface. The model links that force to the tire's deformation and to the conditions of the roll. It gives engineers a way to compare designs and predict energy loss without a road test.

The central output is the rolling resistance force, the drag that acts opposite to travel. A model also produces the rolling resistance coefficient, which normalizes that force by the normal load. Tire deformation energy loss is the physical quantity the model tries to represent.

A complete tire rolling model states its inputs and assumptions before it gives results. Inputs can include load, speed, inflation pressure and tire construction details. Assumptions can include a flat surface, steady speed and a tire that does not slip.

Hysteresis losses inside the tire

Hysteresis losses happen when rubber is deformed and does not return all the energy it absorbed. As the tire rolls, each part of the tread and sidewall is bent and released many times. The energy that is not returned becomes heat.

A model represents hysteresis losses as a fraction of the deformation energy. The fraction depends on the rubber compound and on how far the tire deflects. Tire deformation energy loss is therefore tied to both the material and the load.

The hysteresis approach explains why a tire at low pressure rolls with more resistance. A softer tire deflects more, and more deflection means more energy lost per revolution. The model captures this link between deflection and resistance force.

The rolling resistance force equation

The rolling resistance force equation relates the resistance force to the normal load and a coefficient. The basic form is force equals Crr times the normal load. Crr is the rolling resistance coefficient, a dimensionless number.

The rolling resistance equation becomes more realistic when it adds terms for speed and other effects. A simple model might treat Crr as constant, while a detailed model lets Crr change with speed. The choice depends on the range of conditions the model must cover.

The normal load is the downward force the tire carries. A model that ignores load transfer between tires can misstate the resistance on each axle. Inputs should state how the normal load is measured or assumed.

How load changes the resistance

Load and speed effects on rolling resistance are modeled by making the coefficient depend on the conditions. Resistance force rises with normal load, but not always in direct proportion. A model may use a power relation or a fitted curve.

When the load increases, the tire deflects more, so hysteresis losses increase. The coefficient can fall slightly as load rises because the deflection does not scale exactly with force. A model captures this by fitting the coefficient to measured load points.

Separate tires on the same vehicle carry different normal loads, so a per-tire model gives a better estimate. The model should state whether it treats the vehicle as a single load or as several tires. This choice affects the predicted total resistance.

Speed dependence in the model

Speed dependence enters a rolling resistance model because the tire deforms faster at higher speed. Faster deformation can raise hysteresis losses, so the coefficient may rise with speed. A model states the speed range over which its relation holds.

Some models use a constant coefficient at low speed and add a speed term for higher speed. Others fit a curve over the whole tested range. The rolling resistance force equation can include a speed term to reflect that behavior.

Speed also affects how the tire sheds heat, which in turn affects the rubber. A model that ignores temperature can drift from measured values over long runs. Assumptions about steady speed and thermal conditions should be written down.

Inputs and assumptions a model needs

Tire model inputs and assumptions define the boundary of what the model can predict. Inputs describe the tire, the load, the speed, the pressure and the surface. Assumptions state what the model treats as constant or ideal.

Measured inputs come from bench tests or road tests, and each carries some uncertainty. A model should name the source of its inputs and the conditions they were collected under. Inputs from one tire size may not transfer directly to another.

Assumptions such as a rigid surface or no slip simplify the mathematics. Each assumption adds a limit that the reader should know before using the result. Writing assumptions clearly keeps the model honest.

Steps to build the model

Building a rolling resistance model follows a sequence from physical description to fitted result. The steps below show the order that keeps the model traceable and testable. Each step should be recorded so another engineer can repeat it.

The first steps define the tire and the rolling conditions. The middle steps write the equations for force, coefficient and deformation. The final steps fit the model to measurements and check its range.

A model is not finished until its limits are stated. The builder should describe where the assumptions stop holding and what inputs matter most. This keeps the model useful as a comparison tool rather than a fixed answer.

  • Define the tire, the load, the speed and the pressure range to be modeled.
  • Describe the deformation and hysteresis loss that produce resistance.
  • Write the force equation and the coefficient relation.
  • Add terms for load and speed dependence where needed.
  • Collect measured inputs and record their conditions.
  • Fit the model and check it against separate measurements.

Reading a model's results correctly

A model's results are estimates tied to its inputs and assumptions, not a fixed property of the tire. Two models of the same tire can differ because they treat load or speed differently. The reader should compare the assumptions before comparing the numbers.

The rolling resistance coefficient is only meaningful when its reference load and speed are known. A coefficient quoted without those conditions can mislead a comparison. The model should report the conditions beside every coefficient.

A tire rolling model cannot replace a trained specialist's judgment on safety or durability. Heat buildup and structural limits need expert assessment beyond the model. The model informs design and comparison, while specialists verify the physical result.

Rolling resistance modeling questions

What is a rolling resistance model?

A rolling resistance model is a set of equations that estimates the force opposing a rolling tire. The model links tire deformation, hysteresis losses, normal load and speed to a resistance force and coefficient. It is a prediction tool that depends on stated inputs and assumptions.

How do you calculate rolling resistance force?

Rolling resistance force is calculated as the rolling resistance coefficient Crr times the normal load. More detailed models add terms for speed and other conditions. The force value is only valid for the load and speed the model was built for.

What is the rolling resistance coefficient Crr?

Crr is a dimensionless number that relates the resistance force to the normal load. Crr is not a fixed constant across all conditions, because load and speed change it. A model should report the conditions under which Crr was measured or fitted.

How do load and speed affect rolling resistance?

Higher normal load increases tire deflection and the energy lost to hysteresis. Higher speed can raise the deformation rate and the resistance, depending on the tire and the range. A model states how it treats load and speed effects so the result stays within its valid range.

What inputs does a tire rolling model need?

A tire rolling model needs the tire specification, the normal load, the speed, the inflation pressure and the surface condition. It also needs measured resistance data to fit its coefficients. Each input should be recorded with the conditions under which it was collected.

Why does a model need assumptions?

A model needs assumptions to simplify the physics into workable equations. Assumptions such as steady speed, no slip or a rigid surface define where the model applies. Writing them down lets a reader judge whether the model suits a new situation.

Latest articles