# Replacing Wheel Studs on a Subaru Forester, Outback

How to replace a broken or worn wheel stud on a Subaru Forester or Outback, including hub access, rotor removal, pressing in a new stud, and when a shop is needed.

Replacing a wheel stud on a Subaru Forester or Outback means driving the old stud out of the hub flange and pulling a new one through from behind. You reach the studs by removing the wheel, brake caliper and rotor at that corner. Some corners allow the job with hand tools, while tight clearance or a damaged hub means a shop with a press should do it. 

- A broken wheel stud is pressed into the hub flange, so the new one goes in from the back of the hub.
- You must remove the brake caliper and rotor to reach the stud on a Subaru Forester or Outback.
- A stack of washers and a lug nut can pull a new stud into place when clearance behind the hub allows it.
- A seized stud, a damaged hub hole or no room for a puller points to hub or bearing service by a specialist.
- Check lug nut torque with a torque wrench after the repair so the new stud seats evenly.
 

## How a Subaru wheel stud sits in the hub 

A Subaru Forester or Outback wheel stud is a splined shank pressed into the flange of the hub assembly. The splines bite into the flange so the stud cannot spin when the lug nut is tightened. The threaded end passes through the brake rotor and the wheel, and the lug nut clamps everything together. 

The front hub stud and rear hub stud follow the same layout, but access behind each hub differs. Subaru hub assembly design places the bearing and flange as one unit on many models, so the stud is a service item on the flange rather than a separate bolt. Replacing a stud keeps the hub and bearing in place when the flange is sound. 

A stud that snapped off leaves a short stump in the flange, which is easier to drive out than one broken flush. Inspect the remaining studs and the lug nuts at the same time. A stretched or cross-threaded stud belongs in the same repair, and a damaged hub hole changes the plan. 

## Tools and parts to gather first 

Replacing wheel studs on a Subaru Forester or Outback needs the correct stud for the hub, a lug nut, a stack of washers and a breaker bar. A hammer and a punch drive the old stud out, and a torque wrench sets the lug nuts at the end. [Wheel chocks and jack stands](/articles/wheel-chocks-and-jack-stands-together-for-a-safe-inspection-setup/) make the car stable before any work starts. 

Match the new stud to the old one in thread size, length and spline count. A stud from a different hub may look close but seat poorly in the flange. Buy the stud by the vehicle model and the corner it fits, and compare it with the broken piece before installation. 

Penetrating oil helps on a rusted stud, and a wire brush cleans the flange face. Brake cleaner removes grease from the rotor and hub mating surfaces. A torque wrench is not optional here, because uneven lug nut torque can warp a rotor and loosen the new stud. 

- New wheel stud matched to the hub and corner
- Lug nut, washers and a breaker bar for pulling
- Hammer, punch and penetrating oil
- Jack, jack stands and wheel chocks
- Torque wrench and brake cleaner
 

## Removing the wheel, caliper and rotor 

Rotor removal is the step that opens access to the studs on a Subaru Forester or Outback. Loosen the lug nuts on the ground, raise the corner and set it on a jack stand, then take the wheel off. The brake caliper and its bracket come off next so the rotor can slide free. 

Support the caliper with a strap or wire instead of letting it hang by the brake hose. Remove the caliper bracket bolts and lift the bracket away, then pull the rotor straight off the hub. A rusted rotor may need a tap with a soft mallet, and a rotor held by a screw needs that screw removed first. 

With the rotor off, the stud heads sit exposed on the hub flange. Rotate the hub so the damaged stud faces a clear spot. Clean the flange face before reassembly, and keep brake fluid and grease off the rotor surface. 

## Driving out the old stud 

Driving the old stud out is a matter of striking the threaded end with a hammer and punch. Aim the punch squarely on the stud center and hit it toward the back of the hub. The splines release and the stud drops out behind the flange. 

A stud that will not move with firm hits needs penetrating oil and time, not harder blows. Heavy hammering can damage the wheel bearing, so stop if the stud stays put. A shop with a press can remove a seized stud without stressing the bearing hub replacement parts. 

Catch the stud as it comes free, then inspect the empty hole in the flange. Burrs or an enlarged hole mean the new stud will not hold its splines. A damaged hole points to hub service, and that job belongs to a trained technician. 

## Pulling the new stud into the flange 

A new stud is pulled into the flange from behind, with the splines leading and the threaded end facing out. Seat the splines by hand as far as they go. Then thread a lug nut onto the stud with washers behind it and tighten to draw the stud home. 

The washer stack lets the lug nut pull the stud without bottoming on the hub face. Tighten in stages and watch the stud head as it seats against the back of the flange. Stop when the head sits flush, because over-tightening can strip the threads or stretch the new stud. 

Clearance behind the hub is the limit on this method, and some corners leave no room for the washer stack. When the stud cannot be drawn straight, a shop can seat it with a press. Never grind or cut a stud to make it fit. 

- Oil the stud threads lightly before pulling
- Seat the splines by hand first
- Use a washer stack wider than the hub hole
- Tighten in stages and stop when the head is flush
- Check the stud sits square in the flange
 

## Reassembling the brake and wheel 

Reassembly puts the rotor, caliper bracket and caliper back in the reverse order of removal. Clean the hub face so the rotor sits flat, then slide the rotor on and refit the bracket bolts. Reconnect the caliper and pump the brake pedal before the car moves. 

Mount the wheel and start the lug nuts by hand on the new stud. Snug the nuts in a star pattern, lower the car, then set the final torque with a torque wrench. Recheck the torque after the first drive, since a new stud can settle. 

Test the brakes at low speed in a safe area before normal driving. A soft pedal means air in the system or a caliper problem, and the car should not be driven until it is fixed. The wheel should turn freely with no rubbing or wobble. 

## When the job needs a specialist 

Some Subaru Forester and Outback stud jobs need a shop rather than a driveway repair. A stud broken flush with the flange, a spun stud or a corroded hub can defeat hand tools. A wheel bearing that growls or has play also calls for bearing hub replacement, which is a press job. 

A damaged hub flange, a stripped hole or a stud that will not seat square all point to hub service. Brake work on a car with a soft pedal or a leaking caliper belongs with a trained technician. Lifting and supporting the car incorrectly can injure a person, so use rated stands on level ground. 

Ask the shop to check the other studs and the lug nuts while the corner is apart. A stud that failed from cross-threading suggests the nut and the thread both need attention. The same inspection catches a rotor that is worn below its limit. 

## Keeping studs and lug nuts in good shape 

A wheel stud lasts when the lug nuts are tightened to the specified torque with a torque wrench. Impact wrenches turned up high stretch studs and damage threads over time. Tightening in a star pattern keeps the wheel seated evenly on the hub. 

A light coat of oil on the threads helps, but grease on the taper or the hub face changes the clamp load. Clean the stud threads with a wire brush when rust appears. Replace a lug nut with rounded corners or damaged threads. 

Check the studs whenever a wheel comes off, and look for rust streaks or a loose nut. A stud that shows a stretched neck or a worn thread should be replaced before it fails. Carry the correct lug wrench in the car for roadside wheel changes. 

## Subaru Forester and Outback stud questions 

### How do you replace a wheel stud on a Subaru Forester? 

Replacing a wheel stud on a Subaru Forester starts with removing the wheel, brake caliper and rotor at that corner. Drive the old stud out of the hub flange with a hammer and punch, then pull a new stud in from behind with a lug nut and washers. Reassemble the brake and torque the lug nuts with a torque wrench. 

### How do you replace a wheel stud on a Subaru Outback? 

A Subaru Outback stud replacement follows the same steps as the Forester, with rotor removal to reach the hub flange. Seat the new stud's splines by hand, then draw it in with a lug nut and washer stack. Some corners lack clearance behind the hub, and those need a shop with a press. 

### Can you replace a broken wheel stud on a Subaru Forester at home? 

A broken wheel stud on a Subaru Forester can be replaced at home when the stump stands above the flange and clearance behind the hub allows a puller. A stud broken flush, a rusted hub or a seized stud needs a shop. Brake work and bearing service should go to a trained technician. 

### Do you have to remove the brake rotor to change a wheel stud? 

Yes, rotor removal gives access to the stud heads on a Subaru Forester or Outback hub. The caliper and bracket come off first so the rotor can slide free. With the rotor off, the stud heads sit exposed on the hub flange. 

### Can a wheel stud be replaced without a new wheel bearing? 

Yes, a wheel stud can be replaced without a new wheel bearing when the hub flange and bearing are sound. The stud presses into the flange, and the bearing stays in place during the repair. A growling bearing or a damaged flange calls for bearing hub replacement instead. 

### How tight should lug nuts be after a stud replacement? 

Lug nuts should be tightened to the torque specified for the vehicle with a torque wrench, in a star pattern. A new stud settles, so recheck the torque after the first drive. Avoid high-impact tightening, which can stretch the new stud.
