RC Car Camber Gauge Tool

An RC car camber gauge tool measures wheel lean so you can set suspension geometry accurately. Learn how to read, check and adjust camber on a radio control car.

8 min read0 views
— · 0 votes
Contents
  1. What a camber gauge measures
  2. Types of RC camber gauge
  3. Prepare the car before measuring
  4. Taking a camber reading step by step
  5. Adjusting camber at the turnbuckle
  6. Reading camber numbers on a setup sheet
  7. Where camber fits in suspension setup
  8. Caring for the gauge and keeping readings true
  9. RC Camber Gauge Questions
  10. What does a camber gauge tool for RC cars do?
  11. Can I use a camber gauge with the wheels on the car?
  12. How do I adjust camber on an RC car after measuring?
  13. Why do my two camber readings disagree on the same wheel?
  14. Does camber matter on a small scale RC car?

An RC car camber gauge tool measures how far a wheel leans from vertical, so you can set camber on a radio control car with repeatable numbers instead of guesswork. The gauge sits against the wheel or the hub and reads the angle in degrees, and you compare that number to the setup you want. A small change in camber alters how the tire contacts the ground, which is why the gauge belongs in any serious suspension setup.

  • A camber gauge converts wheel lean into a degree reading you can record and repeat.
  • Set the ride height and check the chassis is flat before you measure camber.
  • Camber is adjusted at the turnbuckle or the upper link that controls the hub angle.
  • Measure both sides and note the numbers, so a setup sheet stays consistent.
  • A gauge that matches your wheel size gives a cleaner reading on small scale cars.

What a camber gauge measures

A camber gauge reads the angle of a wheel relative to vertical, expressed in degrees. Negative camber means the top of the wheel leans inward toward the chassis, while positive camber means the top leans outward. The gauge turns that lean into a number you can write down and compare from run to run.

On a radio control car, the wheel is small, so a few tenths of a degree already changes how the tire sits on the ground. A hobby camber gauge is scaled to read those small angles clearly. Some gauges sit flat against the face of the wheel, and others clamp to the hub or the axle.

The reading describes wheel alignment only in the camber direction. Toe and caster are separate angles, and a camber gauge does not measure them. Use it as one tool in the suspension setup process, alongside a flat setup board and a ride height gauge.

Types of RC camber gauge

Camber gauge designs for radio control cars fall into a few groups, and each suits a different way of working. The choice depends on the wheel size, the space around the hub and whether you measure with the wheels on or off. A gauge that fits your car cleanly gives a steadier reading than one that rocks on the rim.

A plate or bar gauge rests against the wheel face and carries a bubble or a digital angle readout. A hub-mounted gauge attaches to the axle and reads the hub angle directly. Digital angle gauges use an electronic sensor, and analog gauges use a bubble level or a weighted pointer.

Small scale camber gauges are sized for the smaller wheel diameters found on mini and micro cars. A full-size gauge on a tiny wheel can overhang the rim and tilt out of contact. Check the gauge fits the wheel diameter before you rely on its numbers.

Gauge typeWhere it sitsWhat suits it
Plate or bar gaugeAgainst the wheel faceCars with clear access to the rim
Hub-mounted gaugeOn the axle or hubMeasuring with wheels removed
Digital angle gaugeOn a flat reference surfaceReading exact degree values
Bubble gaugeAgainst the wheel faceQuick checks without power

Prepare the car before measuring

Preparation decides whether a camber reading means anything, so set the car up before the gauge touches a wheel. Put the car on a flat, level surface with the battery fitted and the ride height set. The chassis should sit at the height you race or run at, with the tires you intend to use.

Check that the suspension moves freely and that no link is binding. A bound hinge pin or a bent turnbuckle holds the hub at the wrong angle and skews the reading. Bounce the car gently and let it settle before you measure.

Confirm the wheels and tires are the ones you will run, since wheel width and tire shape affect where the gauge contacts. Clean the wheel face so the gauge sits flat. A speck of dirt under a plate gauge tilts it and changes the number.

Taking a camber reading step by step

Taking a reading follows the same order on each corner, which keeps your numbers comparable. Work one wheel at a time and record the value before moving on. Write the reading down rather than trusting memory between corners.

Set the gauge against the wheel or hub as its design requires and hold it steady. Let the bubble or the display settle, then read the angle. Note whether the value is negative or positive, because the sign matters as much as the number.

Repeat the reading once to confirm it. A gauge that gives two different values on the same wheel is not seated properly or the suspension is moving. Fix the seating problem before you adjust anything.

  • Set ride height and fit the running tires.
  • Place the car on a flat, level surface.
  • Seat the gauge flat against the wheel or hub.
  • Let the reading settle and note the sign.
  • Repeat once to confirm the value.
  • Record each corner on a setup sheet.

Adjusting camber at the turnbuckle

Camber adjustment happens at the link that sets the hub angle, which is a turnbuckle on many radio control cars. Turning that link changes its length and tilts the top of the wheel in or out. The gauge tells you how far to move and confirms the result.

Make a small change, then re-measure rather than turning the link by guesswork. Note how much angle one turn of the turnbuckle produces on your car, and use that as your adjustment unit. Keep track of turns in or out so you can undo a change.

Adjust one corner at a time and check the opposite corner afterward, because some suspension designs interact. Tighten lock nuts and check that the link still moves freely. Re-check ride height after adjustment, since a changed link can shift the chassis slightly.

Reading camber numbers on a setup sheet

A setup sheet records camber at each corner, so you can compare runs and return to a known setting. Write the value with its sign, such as minus one degree at the front left. Consistent recording turns the gauge into a useful reference rather than a one-time check.

Record the conditions alongside the numbers, such as the tires fitted and the surface type. Camber that works on one surface may not suit another, and the sheet shows what you changed. Note any other adjustment made in the same session, since two changes at once hide which one worked.

Compare left and right readings rather than a single corner. A difference between sides points to a bent part, a worn hinge or a link set to a different length. The gauge helps you spot that mismatch before it affects handling.

Where camber fits in suspension setup

Camber is one part of RC suspension geometry, and it works together with toe, caster and ride height. Changing one angle alters how the tire contacts the ground, so set the others first where possible. Measure camber after the base setup is stable.

Camber affects the contact patch as the suspension compresses and the body rolls. A wheel that leans inward at rest may sit flatter under load, depending on the suspension design. The gauge measures the static angle, so treat the number as a starting reference.

Keep a written order for setup work, such as ride height, then camber, then toe. Following the same order each time makes your records meaningful. The gauge earns its place by making that order repeatable.

Caring for the gauge and keeping readings true

A camber gauge is a measuring instrument, so treat it as one and store it where it will not bend or scratch. A plate gauge that has been dropped may no longer sit flat. Check it against a known flat surface before trusting a reading.

Digital gauges need a working battery and a stable zero, so check the zero on a flat surface before use. Bubble gauges need a clean vial and an undamaged bubble. Replace or recalibrate a gauge that no longer repeats its own reading.

Keep the wheel face and the gauge contact points clean, and store the gauge away from dirt and moisture. A gauge used on a dirty car picks up grit that tilts it. Small care habits keep the numbers you record worth comparing.

RC Camber Gauge Questions

What does a camber gauge tool for RC cars do?

A camber gauge tool measures the angle of an RC car wheel relative to vertical and shows it in degrees. The reading tells you whether the top of the wheel leans in or out and by how much. You use that number to set and repeat a suspension setup.

Can I use a camber gauge with the wheels on the car?

Yes, a plate or bar style camber gauge is designed to rest against the wheel face with the wheels fitted. A hub-mounted gauge instead reads the axle or hub, which may need the wheel removed. Match the gauge type to the way you prefer to work.

How do I adjust camber on an RC car after measuring?

Adjust camber at the turnbuckle or upper link that controls the hub angle on your car. Turn the link a small amount, then re-measure with the gauge to confirm the new angle. Keep a note of the turns so you can reverse the change.

Why do my two camber readings disagree on the same wheel?

Disagreeing readings on one wheel mean the gauge is not seated flat or the suspension is moving. Clean the wheel face, reseat the gauge and check for a binding hinge or a loose link. Fix the cause before you record a value.

Does camber matter on a small scale RC car?

Yes, camber matters on a small scale car because the wheels are tiny and a small angle change alters the contact patch. A small scale camber gauge reads those tight angles more clearly than a full-size tool. Use a gauge sized to the wheel diameter for a clean contact.

Read next

Latest articles