Preventing Flat Spots on Stored Tires
Learn how flat spots form on stored tires and how to prevent them with pressure checks, rotation, correct storage position and a suitable storage surface.
Contents
- How flat spots form on a stored tire
- Set the inflation pressure before storage
- Take the weight off the tread
- Choose the storage position for loose tires
- Match the storage surface to the tire weight
- Storage conditions that help tire flat spot prevention
- Check on stored tires at intervals
- Questions About Stored Tire Flat Spots
- Can flat spots on stored tires be prevented?
- Does a car storage tire flat spot happen to every tire?
- What inflation pressure should a stored tire hold?
- Is vertical storage better than stacking for preventing flat spots?
- Will a flat spot on a stored tire go away after driving?
Preventing flat spots on stored tires means keeping a tire from resting under load on one contact patch for a long stretch. Flat spot formation happens when the weight of a car or a stack of tires presses into the tread and the rubber takes a set. A few habits of pressure, position and rotation keep the tire shape intact.
- Flat spots come from prolonged load on one contact patch, so a stored tire should not sit pressed against a hard surface.
- A tire on a stored car keeps its shape better at slightly higher inflation pressure than the pressure you drive on.
- Rotating stored tires or lifting the car takes the weight load off the tread.
- A clean, dry, cool storage surface protects the tire as much as the storage position does.
How flat spots form on a stored tire
A flat spot is a flattened area of tread where a tire rested under heavy load without moving. Flat spot formation starts when the rubber and the cords inside the tire deform and slowly hold that shape. The tire then rolls with a thump until it warms and rounds out again.
The load matters more than the storage time. Avoiding prolonged load on one contact patch is the whole principle behind tire flat spot prevention. A tire pressed flat against concrete for a long spell deforms more than one that shares its weight with nothing else.
Temperature plays a part in flat spot formation too. Rubber is softer in heat and stiffer in cold, and a stiff tire resists taking a set. A tire stored in a hot place under load is more likely to keep the shape it was pressed into.
Set the inflation pressure before storage
Inflation pressure while stored decides how firmly the tire holds its round shape. A tire at a low pressure sinks into the contact patch under the weight it carries. Raising the pressure a little spreads that load and keeps the sidewall supported.
Add a modest amount of air before a car goes into storage, and note the starting pressure. Do not inflate to the maximum printed on the sidewall, which is a limit, not a storage setting. Restore the driving pressure before the car returns to the road.
A tire stored off the car also benefits from a little extra air. Pressure slowly escapes from any tire over time, and a soft stored tire is the one that takes a set. Check the pressure again at intervals and top it up as needed.
Take the weight off the tread
The simplest way to stop weight load on tread is to lift the car so the tires hang free. Axle stands under the frame place the load on the suspension and leave the wheels unloaded. A car raised this way takes the sustained pressure off every contact patch at once.
If the car stays on its wheels, move it a short distance at intervals so a fresh part of the tread meets the floor. Even a small roll changes the contact patch and lets the previous spot relax. A short slow roll is enough, and it does not need speed or distance.
Stored tires that are off the car should not be stacked under their own weight for a long spell. A tall stack puts heavy load on the tires at the bottom. A low stack or an upright stance shares the load more evenly.
Choose the storage position for loose tires
Vertical storage keeps a tire standing on its tread edge, and it suits a tire that will sit for a while. A tire standing upright does not carry the weight of other tires on its sidewall. A rack or a stand holds the tire so it stays vertical instead of leaning.
Stacking tires flat on their sidewalls works for a short period, and a low stack limits the load on the lowest tire. Tires that carry a stiff sidewall tolerate a flat stack better than soft ones. Turn and restack flat-stored tires at intervals so each tire sits in a different spot.
Hanging a tire from a hook is a poor storage position. The hook puts a local load on one part of the tread and can distort the tire. Keep hanging storage for short periods and for tires that will be checked before use.
Match the storage surface to the tire weight
Storage surface and tire weight work together, because a hard floor holds the load while a soft one lets the tire sink. Concrete and sealed flooring keep a tire sitting flat and even. A clean floor also keeps grit and oil away from the rubber.
Gravel, soil and rough ground press unevenly into the tread and leave a lumpy contact patch. A tire left on such a surface takes an irregular set rather than a smooth one. Place a firm flat board under a tire that must stay outdoors on rough ground.
A barrier under the tire can keep it off a surface that may react with the rubber. A plain board or a mat does the job without adding softness. Check the barrier stays flat and does not trap moisture under the tire.
Storage conditions that help tire flat spot prevention
A dry, dark and cool place slows the aging that makes a flat spot harder to undo. Sunlight and heat stiffen and dry the rubber over time. A covered, shaded spot protects the tire as it rests.
Keep stored tires away from electric motors, welders and other sources of ozone. Ozone attacks rubber and leaves small cracks that weaken the tread. A separate storage area avoids the exposure.
Oil, solvent and fuel spills soften rubber and mark the tread. Wipe up any spill on the storage floor before a tire goes down. A clean surface under the tire protects the compound that holds its shape.
Check on stored tires at intervals
A stored tire needs a look at intervals, not constant attention. Check the inflation pressure, the storage position and the contact area each time. A tire that has lost pressure is the one most likely to take a set.
Rotate stored tires so a new part of the tread faces the floor or the stack below. Rotating stored tires is a quick job when they stand upright, because each tire can be turned in place. For a flat stack, restack in a different order.
Before a stored car goes back on the road, check the tires cold and set the driving pressure. A short slow drive lets a slight flat spot round out as the tire warms. A flat spot that remains after warming points to a tire that needs a professional inspection.
Questions About Stored Tire Flat Spots
Can flat spots on stored tires be prevented?
Yes, flat spots on stored tires can be prevented in most cases by keeping weight off the tread. The key is avoiding prolonged load on one contact patch through lifting the car, rotating the tires or keeping them vertical. Correct inflation pressure while stored supports the tire shape as well.
Does a car storage tire flat spot happen to every tire?
No, a car storage tire flat spot depends on load, pressure, temperature and how long the tire sits still. A tire stored at correct pressure on a firm surface and turned at intervals takes far less of a set. Softer rubber and heavier loads make a flat spot more likely.
What inflation pressure should a stored tire hold?
A stored tire should hold a little more pressure than the normal driving setting, without going to the sidewall maximum. The exact figure depends on the tire size and the vehicle, so check the door placard or the tire maker's guidance. Return to the driving pressure before the car is used.
Is vertical storage better than stacking for preventing flat spots?
Yes, vertical storage is generally better for long storage because a tire standing upright carries no weight from other tires. Stacking flat works for a short period if the stack stays low. Turn and restack flat-stored tires at intervals to share the load.
Will a flat spot on a stored tire go away after driving?
Often a slight flat spot on a stored tire rounds out after the tire warms on a slow drive. A deep or long-standing flat spot may not clear and can signal internal damage. Have a tire that keeps thumping checked by a trained tire technician.