# Pallet Truck Wheel Size and Dimensions

How to read hand pallet truck wheel size, measure wheel diameter, width and bore, and match a replacement pallet jack wheel to your truck.

A pallet truck wheel size is given by three dimensions: the outside diameter, the tread width and the bore, which is the hole through the hub. A hand pallet truck uses a pair of load wheels under the forks and one or two steer wheels at the handle end. Matching all three numbers, plus the hub fitting, is what makes a replacement wheel sit correctly. 

- Measure diameter across the tread, width across the tread face and bore across the hub hole.
- Load wheels and steer wheels are sized separately, so check each position on the truck.
- A wheel can share a diameter and still differ in bore or hub length.
- The load material, such as polyurethane, affects how the wheel rolls and wears.
- Confirm the axle and bearing type before ordering a replacement pallet jack wheel.
 

## What the three wheel numbers mean 

Pallet truck wheel size comes down to diameter, width and bore, and each one controls a different part of the fit. Diameter is the full height of the wheel from tread to tread, measured through the center. Width is the tread face that touches the floor. Bore is the hole in the hub that takes the axle or bearing. 

The pallet truck wheel diameter sets how the truck rolls over floor joints and how much clearance the forks keep above the ground. A larger diameter rolls over small obstacles with less effort. The width spreads the load on the floor and affects how the wheel tracks in a straight line. 

The bore decides whether the wheel mounts on the axle at all, and a bore that is too large lets the wheel rock. Some wheels carry a bearing inside the hub, and the bearing bore is what you measure. Wheel width and bore are the two figures people leave out, and they are the two that stop a wheel from fitting. 

## Load wheels and steer wheels are different 

A hand pallet truck carries two load wheels inside the fork frame and one or two steer wheels at the handle end. The load wheels sit close together and take the weight of the pallet. Steer wheels turn with the handle and set the direction of the truck. 

The two positions rarely share the same hand pallet truck [wheel dimensions](/articles/wheel-measurements-explained-diameter-width-offset-and-more/), so measure them separately. Load wheels are often smaller in diameter and wider in the tread than steer wheels. Steering wheels are sized for pivoting, and their hub and bearing layout follows that job. 

Buying a set for one position and fitting it at the other can change the fork height. A different diameter at the load wheels tilts the forks and changes how the pallet sits. Note which position each measurement came from before you compare parts. 

## How to measure a pallet truck wheel 

Measuring pallet truck wheel size is easier with the wheel off the truck and clean. Dirt on the tread adds to the diameter reading and gives a false figure. A caliper or a tape with a straight edge across the tread gives a usable number. 

Read the diameter across the full tread, not across the hub or the side plate. Read the width across the tread face only. Push the caliper jaws through the bore to read the hole, or read the bearing bore if a bearing is fitted. 

Write down the hub length as well, which is the distance across the hub between the fork plates. A wheel with the right bore can still bind if the hub is longer than the gap. Photograph the wheel beside the ruler so the numbers stay attached to the part. 

## Steer wheel sizing and the handle end 

The steer wheel at the handle end follows its own size pattern, and its mounting differs from the load wheels. Steering wheels often run in a bracket with a thrust bearing above them. The bracket sets the space the wheel has to fit into. 

Measure a steer wheel the same way: diameter, width and bore. Check the bracket opening and the axle diameter at the same time. A steer wheel that is too wide rubs the bracket, and one that is too narrow can shift sideways on the axle. 

Steering geometry depends on the wheel sitting square in its bracket. A worn or wrong-sized steer wheel makes the truck pull to one side. Replace both steer wheels together when the truck has two, so the handle stays centered. 

## Load materials and the polyurethane option 

The load material changes how a wheel behaves on the floor, and a polyurethane load wheel is one option among several. Polyurethane treads resist oil and roll with less rolling resistance on smooth concrete. Nylon and steel wheels carry heavy loads but can mark soft floors. 

Rubber treads grip better and run quieter on uneven surfaces. Softer materials cushion the load but wear faster on abrasive floors. The floor surface and the load weight decide which material suits the job, more than the wheel size alone. 

Material does not change the diameter, width or bore you need. Order the same size in a different material and the wheel still fits the truck. Compare the material as a separate choice from the dimensions. 

## Matching a replacement pallet jack wheel 

A replacement pallet jack wheel must match the original on diameter, width, bore and hub length. The bearing type and the axle diameter complete the fit. A wheel that matches in size but not in bearing can still fail to mount. 

Measure the old wheel before you search for a new one, rather than trusting a model number alone. Truck makers change wheel fittings between builds, and the same model can carry different wheels. Keep the old wheel until the new one is fitted and the truck rolls correctly. 

Fitting a wheel involves lifting the truck and handling a heavy assembly, and a jack that slips can injure feet and hands. Block the truck securely and use a proper lift. Where the axle or bearing is seized or damaged, a trained technician should do the work. 

## Checking the fit after installation 

A correctly fitted wheel spins freely, sits centered on the axle and does not rub the fork or bracket. Spin each wheel by hand before the truck goes back into service. Listen for grinding, which points to a bearing or a bore that is too tight. 

Set the truck on a flat floor and check that the forks sit level and at the right height. A new wheel of the wrong diameter shows up as a tilt in the forks or a pallet that will not clear the floor. Roll the truck a short distance and check that it tracks straight. 

Recheck the axle nut or retaining clip after the first use, since a loose wheel can come off under load. Look at the tread contact pattern to see whether the wheel sits flat on the floor. Any wobble or rubbing means the wheel comes off for another measurement. 

## Sizes vary, so measure your own truck 

There is no single pallet truck wheel size, because the dimensions depend on the truck model, its load rating and the wheel position. Two trucks of similar look can use different wheels. The measurements on your own truck are the only ones that matter. 

Write the diameter, width, bore and hub length on a label and keep it with the truck's service notes. The next replacement then starts from known numbers. Compare any catalog figure against those numbers before ordering. 

Where the wheel is worn past its tread or the hub is damaged, the original size can be hard to read. A trained technician can identify the correct replacement from the truck itself. Do not fit a wheel that only matches on diameter. 

## Pallet truck wheel sizing questions 

### What is the wheel size on a hand pallet truck? 

A hand pallet truck wheel size is stated as diameter, tread width and bore, and it varies with the truck model and the wheel position. Load wheels and steer wheels are measured separately because they rarely share the same figures. Measure your own truck rather than assuming a standard size. 

### How do I measure a pallet truck wheel for a replacement? 

Measuring a pallet truck wheel means reading the outside diameter across the tread, the width across the tread face and the bore through the hub. Add the hub length across the hub, since a longer hub can bind against the fork. Clean the wheel first so dirt does not add to the readings. 

### Can I fit a load wheel and a steer wheel of the same size? 

A load wheel and a steer wheel can share a diameter, but they still need to match their own mounting. The bracket, axle and bearing layout at the steer end differ from the load wheel position. Fit each wheel to the position it was measured for. 

### What is a polyurethane load wheel? 

A polyurethane load wheel is a wheel with a polyurethane tread, chosen for smooth floors and resistance to oil. Material is a separate choice from size, so the same diameter, width and bore can come in polyurethane or another tread. The floor surface and load weight decide which material suits the job. 

### Why does the bore matter as much as the diameter? 

The bore sets the hole that takes the axle or bearing, so a wrong bore stops the wheel from mounting or lets it rock. A wheel with the correct diameter and width can still fail on bore alone. Measure the bore or bearing bore and the axle diameter together. 

### Do pallet truck wheels come in one standard size? 

Pallet truck wheels do not come in one standard size, because dimensions depend on the truck model, load rating and wheel position. Catalogs list many sizes and fittings. Compare any listed size against the measurements from your own truck before ordering.
