# P-Metric, Euro-Metric, LT and Flotation Tire Size Designations Compared

How the P-metric, Euro-metric, LT and flotation size systems differ on the sidewall, and what each designation tells you about load and use.

P-metric, Euro-metric, LT and flotation are four ways of writing a tire size on the sidewall. They share the same width and rim numbers but differ in how the load is expressed and which vehicles the size is built for. Reading the letter in front of the size tells you which system you are looking at. 

- A size starting with P is a P-metric tire, written for passenger cars and light-duty vehicles.
- A size with no letter before the width is a Euro-metric tire, the European passenger standard.
- A size starting with LT is an LT tire built for light trucks and carrying load range letters.
- A flotation size uses inches and a decimal width, aimed at off-road fitments.
- The same width and rim numbers do not make two tires interchangeable across systems.
 

## What a tire size designation contains 

A tire size designation is the string of numbers and letters molded into the sidewall. It always pairs a section width with a rim diameter, then adds a load index and a speed rating. The system letter or its absence sits in front of the width. 

The section width is the widest point of the inflated tire, measured from sidewall to sidewall. That figure is expressed in millimeters in the metric systems and in inches in the flotation system. The rim diameter follows, either in inches or in a metric rim code. 

[Load index and speed rating](/articles/tire-load-index-load-range-speed-ratings-material-44528/) complete the size string in the metric systems. The load index is a code for how much weight one tire can carry at a stated inflation pressure. The speed rating is a letter for the maximum speed the tire is built to sustain. 

## The P-metric tire and its passenger role 

A P-metric tire carries a P before the width, as in P225/60R16. The P marks a size designed to the passenger-car standard used in North America. It fits sedans, crossovers and light-duty pickups where the load stays within the passenger envelope. 

The load index on a P-metric tire is quoted at a defined inflation pressure for passenger service. That load figure drops if you inflate the tire below the pressure the index refers to. The sidewall shows the maximum load and the pressure that supports it. 

A P-metric size is not the same as an LT size of identical width and rim. The P-metric version carries a lower load capacity and a softer construction. Substituting one for the other changes what the vehicle can carry. 

## The Euro-metric tire and its plain format 

A Euro-metric tire shows no letter before the width, as in 225/60R16. The plain format is the European passenger standard, and it covers the same passenger role as a P-metric size. Width, aspect ratio, construction and rim diameter are written the same way. 

Load index and speed rating appear on a Euro-metric tire in the same positions as on a P-metric tire. The load index refers to a European pressure table rather than the North American passenger table. That difference matters when you compare a plain size with a P size of identical dimensions. 

A Euro-metric tire can carry a higher load index than a P-metric tire of the same size. The two look alike on the sidewall apart from the missing letter. Check the load index and the pressure table before treating them as equals. 

## The LT tire and light truck service 

An LT load range tire starts with LT, as in LT265/70R17, and is built for light trucks, vans and heavy-duty pickups. The LT marks a reinforced construction meant for higher loads and tougher duty. Load range letters such as C, D and E appear on the sidewall alongside the load index. 

Load range letters describe the ply rating and the inflation pressure the tire is built to take. A higher load range letter means a stronger carcass and a higher maximum pressure. The load index on an LT tire is quoted at that higher pressure, not at passenger pressure. 

An LT tire of the same width and rim as a P-metric tire is heavier and stiffer. Fitting an LT size where a P size was specified changes ride, steering feel and the pressure the vehicle expects. Follow the vehicle placard before swapping between the two systems. 

## The flotation tire and its inch sizing 

A flotation tire is written in inches, as in 33x12.50R15, with the overall diameter first and the section width second. The decimal width and the inch diameter set it apart from every metric format. Flotation sizes suit off-road vehicles that run wide, tall tires at low pressure on soft ground. 

The first number of a flotation size is the approximate overall diameter, not the section width. The second number is the section width in inches, and the R marks radial construction. Rim diameter closes the string in inches. 

A flotation size does not carry a load index in the same way as a metric size. Load capacity is tied to the flotation standard and to the inflation pressure you run. A flotation tire often needs a lift or trimming to clear the body, so check clearance before fitting. 

## How the four systems line up side by side 

The four systems answer different questions about the same tire dimensions. P-metric and Euro-metric cover passenger duty, LT covers light truck duty and flotation covers off-road fitments. Matching width and rim numbers hide real differences in load and construction. 

Comparing a P-metric and a Euro-metric size of identical numbers shows how the load table changes the answer. Comparing either with an LT size shows how the carcass and pressure change the answer. Comparing all three with a flotation size shows how the unit of measurement changes the answer. 

A tire size designation never tells you the whole story on its own. The system letter, the load index, the speed rating and the sidewall markings together define what the tire can do. Read all of them before you compare two sizes. 
| System | Example | Width unit | Built for | 
| P-metric | P225/60R16 | Millimeters | Passenger and light-duty vehicles | 
| Euro-metric | 225/60R16 | Millimeters | Passenger vehicles | 
| LT | LT265/70R17 | Millimeters | Light trucks and vans | 
| Flotation | 33x12.50R15 | Inches | Off-road and soft-ground use |  

## Reading sidewall markings before you compare 

Sidewall markings carry the size string, the load index and the speed rating in a fixed order. The system letter sits at the front of the size, and the service description follows the rim diameter. A trained eye reads the whole line before judging two tires as equivalent. 

Maximum load and maximum pressure appear separately on the sidewall. Those figures belong to the tire alone and do not replace the vehicle placard. The placard states what the vehicle needs, and it takes priority when you choose a replacement size. 

Mixing systems on one vehicle can upset handling and load balance. Keep the same system and the same service description across an axle at minimum. A tire technician can confirm whether a swap keeps the vehicle within its specified load and speed. 

## Choosing between the systems safely 

Match the system on the vehicle placard before you consider a different size. A placard that specifies a P-metric size expects a P-metric tire with at least the same load index. Moving to an LT size raises capacity but changes pressure and ride, so confirm it suits the vehicle. 

Check rim width, overall diameter and clearance whenever you change system. A flotation size can add height that the wheel well cannot take. An LT size can add weight that the suspension and brakes were not set up for. 

Load and speed requirements come from the vehicle, not from the tire alone. Have a trained technician verify the fitment when the new size differs in system, load index or diameter. A wrong match can affect braking distance and tire life. 

## Questions about tire size systems 

### What does P-metric, Euro-metric, LT and flotation mean on a tire? 

These are four size systems written on the sidewall. P-metric and Euro-metric are passenger systems that differ only in the letter and load table. LT is the light truck system with load range letters, and flotation is an inch-based system for off-road fitments. 

### Can I replace a P-metric tire with a Euro-metric tire of the same size? 

A Euro-metric tire of the same dimensions can fit the same rim, but the load index may differ. Compare the load index on both sidewalls and check the vehicle placard before you swap. A trained technician can confirm the replacement meets the vehicle load requirement. 

### Is an LT tire the same as a P-metric tire in the same size? 

No, an LT tire is not the same as a P-metric tire even when width and rim match. The LT tire has a stronger carcass, a higher maximum pressure and a heavier build. It changes ride and steering, so check the placard before fitting one. 

### How do I read a flotation tire size like 33x12.50R15? 

The first number is the approximate overall diameter in inches. The second is the section width in inches, and the R marks radial construction. The last number is the rim diameter in inches. 

### Does the load index mean the same thing in every size system? 

No, the load index refers to a pressure table that differs between systems. A P-metric and a Euro-metric tire with the same index can carry different loads. An LT tire quotes its load at a higher pressure than a passenger tire does. 

### What should I check before changing from one size system to another? 

Check the vehicle placard, the rim width, the overall diameter and the clearance around the tire. Confirm the new load index and speed rating meet or exceed the original. A trained technician should verify the fitment before you drive on it.
