# Motorcycle Tire Size Guide for the Philippines

Read motorcycle and scooter tire sizes sold in the Philippines: the sidewall format, inch to metric conversion, front and rear pairings, and how to check local stock.

A motorcycle tire size in the Philippines is read from the sidewall marking, which gives the width, the aspect ratio and the rim diameter. Scooters and small bikes often use an inch format, while larger motorcycles use a metric format, and both appear on the same shelves. The guide below explains each number and how to compare a listed size with the one your bike needs. 

- Read width, aspect ratio and rim diameter from the sidewall before shopping.
- The inch format (like 80/90-17) and the metric format (like 110/70-17) describe the same dimensions in different ways.
- Front and rear tires carry separate sizes, and the pair should follow the motorcycle maker's specification.
- A size that is listed online may not be stocked locally, so confirm availability before ordering.
- Load and speed markings also sit on the sidewall and should match or exceed the bike's requirements.
 

## Reading the sidewall markings 

Motorcycle [tire sidewall markings](/articles/tire-sidewall-symbols-dates-approval-markings-material-44526/) follow a set format that repeats across brands sold in the Philippines. The first number is the nominal width in millimeters or inches. A slash follows in the metric format, then the aspect ratio, which is the sidewall height as a percentage of the width. 

A hyphen and two digits give the rim diameter in inches in both formats. Letters after the size show the load index and the speed rating, and a separate code may show the construction type. Tubeless and tube-type tires are marked clearly, which matters when the rim is designed for only one of them. 

The sidewall also carries the motorcycle maker's recommended cold inflation pressure in many cases. Treat that figure as a starting point and check the owner's manual for the load you carry. A size label never overrides the pressure advice for the bike. 

- Width: nominal section width in millimeters or inches
- Aspect ratio: sidewall height as a percentage of width
- Rim diameter: the wheel size in inches
- Load index: the maximum load the tire can carry
- Speed rating: the maximum speed the tire is rated for
- Construction: radial or bias-ply, plus tubeless or tube-type
 

## Metric format and inch format explained 

Two size formats appear on motorcycles in the Philippines, and confusing them is a frequent buying mistake. The metric format, such as 110/70-17, states width in millimeters, then the aspect ratio, then the rim in inches. The inch format, such as 2.75-17, states width and rim in inches with no aspect ratio. 

In the inch format the sidewall height is implied by the width, so the two numbers are not a simple width and height. A conversion between formats is approximate because the aspect ratio of an inch-size tire varies by maker. Use a conversion as a starting reference and confirm the result against the motorcycle specification. 

Aspect ratio drives the overall diameter of the tire and therefore the gearing and speedometer reading. Fitting a lower aspect ratio reduces the diameter, and fitting a higher one raises it. Keep the overall diameter close to the original when the bike's electronics depend on wheel speed. 
| Format | Example | What the numbers mean | 
| Metric | 110/70-17 | 110 mm width, 70% aspect ratio, 17 inch rim | 
| Metric rear | 140/70-17 | 140 mm width, 70% aspect ratio, 17 inch rim | 
| Inch | 2.75-17 | 2.75 inch width, 17 inch rim, aspect ratio fixed by maker | 
| Inch wide | 3.00-17 | 3.00 inch width, 17 inch rim, aspect ratio fixed by maker |  

## Front and rear sizes differ 

Front and rear motorcycle tires carry different sizes because each wheel does a different job. The front tire is narrower for steering response, and the rear is wider to put down drive force. The motorcycle maker sets a pairing, and the pair should be treated as a unit. 

Fitting a wider rear tire than specified can change handling and may rub the swingarm or chain guard. A narrower front tire can alter steering feel and braking stability. Check clearance at the fender, the fork legs and the swingarm before committing to a size change. 

Scooters often use a small front and a small rear with different widths, and the sizes are listed in the owner's manual. Underbone motorcycles in the Philippines often run an inch format on both wheels. Record both sizes before you shop so a seller can match the pair. 

## Checking local tire availability 

Local tire availability in the Philippines varies by size, and a size that appears in a regional chart may not be on a shelf nearby. Dealers stock sizes that fit the motorcycles sold in their area. A size for a less distributed model may need an order. 

Ask the dealer for the exact sidewall string, not just the width, because a 110/70-17 and a 110/80-17 are different tires. Confirm the [load index and speed rating](/articles/tire-load-index-load-range-speed-ratings-material-44528/) at the same time. Availability of a brand or model is separate from availability of the size itself. 

A regional tire chart shows which sizes a maker offers in the region and is a useful planning tool. The chart does not confirm that a specific shop holds the tire today. Treat the chart as a range of options and the dealer as the source on stock. 

## Comparing a listed size with your bike 

A size comparison starts with the motorcycle's original specification and the physical clearances around the wheel. Write down the original size from the sidewall of the tire fitted now. Then compare the candidate size on width, aspect ratio and rim diameter. 

The rim width must suit the tire width, and a tire too wide for the rim distorts its profile. Check the [rim width marking](/articles/passenger-car-rim-size-markings-material-46552/) stamped on the wheel or in the manual. A tire too narrow for the rim can also seat poorly and wear unevenly. 

Overall diameter is the result of width, aspect ratio and rim, so two tires with different formats can end up close in diameter. Calculate the diameter before you decide whether a swap fits. Leave clearance for the fender, the brake caliper and the swingarm at full suspension travel. 

## When a size needs a specialist 

Some size changes need a trained technician rather than a home fit. A change that alters rim width, brake clearance or suspension travel should be checked by a shop with the right tools. Tire mounting on a motorcycle rim also needs a balance check afterward. 

Mixing a radial and a bias-ply tire on the same motorcycle is a decision for the maker's guidance. Do not assume that two tires with a matching size string behave the same way. Ask the dealer for the maker's fitment advice when the pair is not the original specification. 

A damaged sidewall, a bulge or a tire that loses pressure quickly needs professional inspection. Do not ride on a tire that shows cords or deep cuts, and do not attempt a repair on a sidewall injury. These cases go to a tire technician, not to a size chart. 

## Load index and speed rating on the label 

Load index and speed rating are part of the size label and belong in the buying decision. The load index is a code for the maximum load the tire can carry at its rated pressure. The speed rating is a letter code for the maximum speed the tire is rated for. 

Fit a tire whose load index and speed rating meet or exceed the motorcycle maker's specification. A lower rating reduces the margin the maker designed in. The rating sits after the rim diameter in the size string, for example in a marking that ends with a number and a letter. 

Load and speed codes differ from the [width and aspect ratio](/articles/comparing-tire-width-and-aspect-ratio/), so read the whole string. A seller may quote only the size and leave out the ratings, which hides part of the specification. Ask for the full sidewall string before you agree to a purchase. 

## Building a size reference for your bike 

A personal size reference saves time at the dealer and prevents a wrong purchase. Note the original front and rear sizes, the rim widths and the load and speed ratings. Add the tire pressures from the owner's manual for the loads you carry. 

Record the overall diameter of each original tire so a future swap can be compared against it. Note the clearance at the fender, fork and swingarm as a visual check. Store the reference with the bike documents so it is available when a tire needs replacing. 

Update the reference whenever a size change is made with professional advice. A reference built from the sidewall and the manual stays accurate across brands. Sellers can then match the exact string rather than guessing from a photo. 

## Motorcycle tire size questions 

### What does a motorcycle tire size guide for the Philippines cover? 

A [motorcycle tire size guide](/articles/reading-motorcycle-tire-size-sidewall-markings-material-45777/) for the Philippines covers the sidewall format, the difference between inch and metric sizes, and how front and rear sizes pair. It also explains how to check what local dealers stock. The guide does not replace the motorcycle maker's specification for your model. 

### How do I read a tire size chart by vehicle in the Philippines? 

A [tire size chart by vehicle](/articles/find-tyre-size-by-reg-material-45371/) in the Philippines lists the sizes a maker offers for a model or a range of models. Start with your own sidewall marking and the owner's manual, then use the chart to see the sizes offered for that model. The chart is a reference, and the dealer confirms what is in stock. 

### Can I convert an inch tire size to a metric size? 

An inch tire size can be converted to a metric size only approximately, because the aspect ratio of an inch-size tire is set by its maker. The conversion gives a starting reference for width and rim diameter. Confirm the result against the motorcycle specification and the physical clearance on the bike. 

### Why are the front and rear motorcycle tire sizes different? 

Front and rear motorcycle tire sizes are different because each wheel has a separate job. The front is narrower for steering, and the rear is wider for drive force. The motorcycle maker sets the pairing, so fit both sizes to that specification. 

### Does the load index matter when I choose a tire size? 

Yes, the load index matters when you choose a tire size because it states the maximum load the tire can carry. Fit a tire whose load index and speed rating meet or exceed the maker's specification. A lower rating reduces the safety margin designed into the motorcycle. 

### What should I check before buying a tire size that is not original? 

Check rim width, fender and swingarm clearance, brake clearance and overall diameter before buying a non-original tire size. Ask a trained technician when the change affects rim width or suspension travel. Confirm the load index and speed rating against the motorcycle specification.
