Mitutoyo Digital Caliper Accuracy: Specifications and Checking Tolerance
How Mitutoyo digital caliper accuracy is specified, how accuracy tolerance and error acceptance work, and how a calibration check with gauge blocks is done.
Contents
- Reading the accuracy specification
- What error acceptance means
- Gauge blocks and a caliper checker
- Mitutoyo caliper accuracy questions
- What is the accuracy of a Mitutoyo digital caliper?
- How do you calibrate Mitutoyo digital calipers?
- How accurate is a Mitutoyo caliper checker?
- What causes a digital caliper to read outside its tolerance?
Mitutoyo digital caliper accuracy is stated as a tolerance across the measuring range, not as a single fixed error, so any reading can sit inside a small band above or below the true size. The accuracy specification, the resolution on the display and the calibration check you perform are three separate things, and a caliper can pass one while failing another. This page explains what the Mitutoyo specifications mean, how accuracy tolerance and error acceptance are judged, and how gauge blocks and a caliper checker are used to confirm a caliper still measures within its stated tolerance.
Reading the accuracy specification
A Mitutoyo digital caliper carries an accuracy tolerance that applies over its full measuring range, so the permitted error is a band rather than one number. The specification pairs that tolerance with a resolution, which is the smallest increment the display shows; a fine resolution does not by itself make the caliper more accurate. Mitutoyo specifications also state repeatability, which describes how closely repeated readings of the same size agree. Judge the caliper against the tolerance for its range, not against the last digit on the screen.
What error acceptance means
Error acceptance is the rule that decides whether a caliper's deviation from a true size counts as a pass or a fail. Each checked point is compared with the accuracy tolerance for that part of the measuring range, and the caliper is accepted when every reading falls inside the band. A single point outside the band is an error acceptance failure, even if the other points are close. Record the deviation at each point so the pattern of error is visible, not just the final verdict.
Gauge blocks and a caliper checker
Gauge blocks are certified reference sizes, and they give the caliper a known length to measure during a calibration check. A caliper checker holds the blocks or a stepped reference and presents each size squarely to the jaws, which reduces the effect of tilting the caliper. Mitutoyo checker accuracy depends on the checker's own tolerance, so the reference must be tighter than the caliper tolerance you are testing. Check the outside jaws, the inside jaws and the depth rod, because each measuring face can drift on its own.
Mitutoyo caliper accuracy questions
What is the accuracy of a Mitutoyo digital caliper?
Mitutoyo digital caliper accuracy is published as a tolerance that applies across the measuring range, not as one fixed figure for every size. The stated tolerance tells you the largest permitted deviation between the display and the true size at any point in that range. Always read the specification for the exact model and range, because the permitted band differs between caliper sizes. Resolution on the display is a separate figure and does not define accuracy.
How do you calibrate Mitutoyo digital calipers?
Calibrating a Mitutoyo digital caliper means comparing its readings with certified reference sizes and adjusting or correcting it where the deviation exceeds the tolerance. Clean the jaws and the reference first, then close the jaws and zero the display before checking each size. A full calibration that returns a certificate belongs with a trained specialist and a controlled reference set. A user check with gauge blocks confirms the caliper is still within tolerance but does not replace that calibration.
How accurate is a Mitutoyo caliper checker?
Mitutoyo checker accuracy is set by the tolerance of the checker itself, which must be tighter than the caliper tolerance being tested. A checker that is no more accurate than the caliper cannot prove the caliper is within its band. Confirm the checker's stated tolerance and its calibration status before you rely on a pass result. The reference and the caliper should also be at a stable temperature during the check.
What causes a digital caliper to read outside its tolerance?
A digital caliper drifts outside its tolerance when dirt, wear or a damaged jaw changes the gap between the measuring faces. A tilted caliper or a jaw that does not close flat adds error that shows up at some sizes and not others. Temperature differences between the caliper, the reference and the part also shift the reading. Clean the faces, zero the display and recheck before you assume the electronics are at fault.