# Metric Tire Size Conversion to Inches

Learn how to convert a metric tire size to inches using the sidewall numbers, the 25.4 factor and a simple formula for width, sidewall and overall diameter.

Metric tire size conversion to inches turns the three numbers on a sidewall into width and height figures you can compare. The first number is the section width in millimeters, the second is the aspect ratio, and the last is the rim diameter in inches. Dividing the width by 25.4 and doing one more step for the sidewall gives you the tire size in inches. 

- Divide the section width in millimeters by 25.4 to get the tire width in inches.
- Multiply the width in millimeters by the aspect ratio, then divide by 2540, to get one sidewall in inches.
- Add twice the sidewall in inches to the rim diameter to get the overall diameter.
- The rim diameter in a metric size is already stated in inches, so it needs no conversion.
- The result is a nominal figure from the sidewall numbers, not a measured size of a specific tire.
 

## What the metric sidewall numbers mean 

A metric tire size such as 285/70R17 packs three measurements into the sidewall markings. The first number is the section width in millimeters, the distance across the widest part of the inflated tire. The second number is the aspect ratio, the sidewall height as a percentage of that width. 

The letter R describes the internal construction and is not a measurement, while the final number is the rim diameter in inches. Metric sizing of this kind is used for passenger car and light truck tires, including P-metric and Euro-metric sizes. The same structure applies to any [width and aspect ratio](/articles/comparing-tire-width-and-aspect-ratio/) you find on a sidewall. 

Those sidewall numbers are nominal values set by the manufacturer's size designation, not a tape measure reading. A tire marked 285/70R17 has a theoretical section width of 285 millimeters and a sidewall equal to 70 percent of it. Reading the three numbers in order is the first step of any metric to inch tire size conversion. 

## Convert millimeters to inches with 25.4 

One inch equals 25.4 millimeters, and that conversion factor 25.4 is the basis of every metric to inch tire conversion. To convert millimeters to inches, divide the millimeter figure by 25.4. A section width of 285 millimeters becomes about 11.22 inches on a calculator. 

The same division handles any tire width in millimeters, whether you are checking a 305 tire width or a narrow passenger size. Tire size millimeters to inches work is therefore simple arithmetic rather than a special table. Round the answer to two decimal places for a practical inch equivalent. 

A metric to inches [tire size calculator](/articles/tire-size-calculator-diameter-comparison-material-44527/) does exactly this division and then carries the result into the sidewall and diameter steps. Doing the math by hand keeps the formula visible, which helps when you compare several sizes. The conversion factor never changes, so the method works for any metric tire size you meet. 
| Sidewall number | What it is | Unit on the sidewall | Conversion step | 
| First number, such as 285 | Section width | Millimeters | Divide by 25.4 | 
| Second number, such as 70 | Aspect ratio | Percentage, no unit | Multiply width by it, then divide by 2540 | 
| Last number, such as 17 | Rim diameter | Inches | None needed |  

## Find the sidewall height in inches 

Sidewall height in inches comes from the aspect ratio applied to the section width. Multiply the width in millimeters by the aspect ratio, then divide by 2540 to get one sidewall in inches. For a 285/70R17, that is 285 times 70 divided by 2540, which gives about 7.85 inches. 

An aspect ratio of 70 means the sidewall is 70 percent of the section width, so both figures must be used together. The aspect ratio has no unit of its own, which is why the division by 2540 appears in the formula. A lower aspect ratio produces a shorter sidewall for the same width. 

The sidewall number on the sidewall is often called the profile, and it changes the look and the overall height of the tire. Two tires with the same width but different aspect ratios end up with different sidewall heights in inches. Get this step right and the overall diameter calculation follows easily. 

## Calculate overall diameter from the metric size 

Overall diameter in inches equals twice the sidewall in inches plus the rim diameter. A 285/70R17 converts to roughly 7.85 inches of sidewall on each side of a 17 inch rim. Doubling the sidewall and adding 17 gives an overall diameter near 32.7 inches. 

The overall diameter formula is the same for every metric tire, so you can compare a 305 tire to a narrower size in one line. Width in inches comes from the first number alone, while diameter depends on all three numbers. That is why one size can be wider than another but shorter overall. 

This overall diameter is a calculated figure from the sidewall markings, and a mounted tire can differ slightly. Tire pressure, load and rim width all affect the real measurement. Use the calculated number for comparison and confirm the physical size at the vehicle or with a tire professional. 

## Work through an example: 285/70R17 

Converting 285 70r17 to inches takes three short steps that use the same formula every time. Start with the width, apply the aspect ratio to get the sidewall, then add the rim. Writing each step down prevents a mistake when you compare several sizes. 

The width of 285 millimeters divided by 25.4 gives about 11.22 inches. The sidewall is 285 times 70 divided by 2540, which is about 7.85 inches. Twice 7.85 plus 17 comes to about 32.7 inches of overall diameter. 

A 305 metric tire to inches follows the same path, with 305 divided by 25.4 near 12.01 inches of width. Its sidewall depends on the aspect ratio that follows the slash. Run the numbers for each size you compare and the inch values line up side by side. 

## Use a metric to inches tire size chart 

A metric to inches [tire size chart](/articles/commercial-truck-and-bus-tire-sizes-common-sizes-and-their-dimensions/) lists common widths and their inch equivalents so you can skip the arithmetic. The chart is a shortcut, and the conversion formula remains the check when a size is missing. Treat chart values as rounded nominal figures from the sidewall numbers. 

A tire size conversion chart from metric to inches typically gives section width, sidewall and overall diameter for each size. A metric to inch tire size chart for width alone is shorter, because diameter needs the aspect ratio as well. Check which figures a chart includes before you rely on it. 

Building your own short chart from the formula is reliable and takes little time. List the sizes you are comparing, then fill in width, sidewall and diameter in inches for each. A hand-made chart also shows where two different metric sizes land close to the same inch dimensions. 

## Metric versus standard inch tire sizes 

Standard tire sizes and metric sizes describe the same dimensions in different ways, which is why a metric to standard tire conversion is useful. A standard size such as 33x12.5R17 states overall diameter and width directly in inches. A metric size states width in millimeters and sidewall as a percentage. 

Comparing the two systems means converting the metric size into inch width and inch diameter first. The 285/70R17 above lands near 32.7 inches in diameter and 11.22 inches in width, close to an inch size around 33x11.5R17. Exact matches are rare because the two systems round differently. 

P-metric and Euro-metric sizes use the same millimeter and aspect ratio structure, so the conversion formula covers both. The letter P marks a passenger vehicle size, and the metric to imperial tire size conversion treats it the same way. What changes between systems is the starting unit, not the geometry. 

## Limits of a calculated inch equivalent 

A calculated inch equivalent is a nominal figure, and the real tire can differ from it. Rim width, inflation pressure and the manufacturer's own tolerances shift the mounted dimensions. The sidewall numbers give a consistent basis for comparison rather than an exact physical measurement. 

Speed rating, load index and construction sit alongside the size numbers and are not part of the conversion. Two tires with identical metric sizes can therefore differ in load capacity and in measured width. Keep the conversion focused on geometry and read the other markings separately. 

Changing to a size with a different overall diameter affects speedometer readings, clearance and gearing. A trained tire specialist should confirm fitment before a size change, especially on a vehicle with limited clearance. The calculated inch values guide the comparison, and the specialist checks the rest. 

## Metric Tire Size Conversion Questions 

### How do I convert a metric tire size to inches? 

Divide the section width in millimeters by 25.4 to get the width in inches. Multiply the width by the aspect ratio and divide by 2540 to get one sidewall in inches. Double that sidewall and add the rim diameter to get the overall diameter in inches. 

### What is 285/70R17 in inches? 

A 285/70R17 converts to about 11.22 inches of width and 7.85 inches of sidewall. Doubling the sidewall and adding the 17 inch rim gives an overall diameter near 32.7 inches. These are nominal figures taken from the sidewall numbers. 

### Is a metric to inches tire size calculator accurate? 

A metric to inches tire size calculator is accurate for the nominal dimensions printed on the sidewall. The real mounted tire can differ slightly because of rim width, pressure and manufacturer tolerance. Use the calculator to compare sizes and confirm the physical size separately. 

### How many millimeters are in an inch for tire conversion? 

One inch is 25.4 millimeters, and that factor is the basis of the entire conversion. Divide any millimeter figure by 25.4 to get inches. The rim diameter in a metric size is already given in inches and needs no conversion. 

### Why do metric and standard inch tire sizes not match exactly? 

Metric sizes describe width in millimeters and sidewall as a percentage, while standard sizes state diameter and width in inches. Each system rounds its numbers differently. A converted metric size therefore lands close to an inch size without matching it exactly.
