Measuring Tire Width with String
Learn how to measure tire width with string and a tape measure, tell tread width from sidewall width, and convert the result to millimeters.
Contents
- Why use string to measure a tire
- Choosing string and marking the span
- Measuring tread width with string
- Measuring sidewall width with string
- Reading the marked string on a tape measure
- Keeping the string measurement accurate
- Checking your figure against the sidewall
- Questions About String Tire Measurement
- Can I measure tire width with string instead of a tape measure?
- How do I mark the string on the tire correctly?
- Is tread width the same as sidewall width on a tire?
- How do I convert my string measurement to tire width in millimeters?
- What kind of string should I use to measure a tire?
Measuring tire width with string works by wrapping a piece of string around the tread or across the sidewall and then laying that string against a tape measure. The string holds the curve of the tire so a flat tape can read it. Mark the string at both ends of the span you want, then measure between the marks.
- String follows the curve of a mounted tire, which a stiff tape measure cannot do on its own.
- Mark the string clearly at each end of the span before you lift it off the tire.
- Tread width and sidewall width are different measurements taken at different points.
- Lay the marked string flat against a tape measure to read the result in millimeters.
- Measure at more than one point around the tire to check that your reading is consistent.
Why use string to measure a tire
String measuring gives you a flexible line that follows the rounded shape of a tire. A tape measure alone tends to bridge the curve instead of tracing it, which shifts the reading. The string method keeps the true path of the surface you are measuring.
The string method needs only household tools: a length of non-stretchy string, a pen, and a measuring tape. String has no markings, so the tape measure does the counting once the string is marked. This makes string a useful tape measure alternative when the tape is too stiff for the job.
String is most useful on a tire that is still mounted on the wheel, where the sidewall curves away from a straight edge. A soft string presses against the surface and records where it starts and stops. Keep the string taut but do not pull it so hard that it sinks into the rubber.
Choosing string and marking the span
A piece of string that does not stretch gives the most faithful reading of tire width. Cotton twine or thin cord works, while elastic cord stretches under tension and spoils the measurement. Cut a length longer than the span you expect to measure.
Marking string on the tire is the step that fixes the measurement. Hold one end at the first edge, run the string across or around the surface, and make a pen mark exactly at the second edge. A fine-tip pen gives a sharper mark than a thick marker.
Two marks matter: one at the start and one at the end of the span. A single mark tells you nothing once the string comes off the tire. Mark both points while the string is still in place, then check the marks before you lift the string away.
Measuring tread width with string
Tread width is the distance across the running surface of the tire, from one shoulder edge to the other. String helps here because the tread often curves toward the shoulders. Press the string into the tread path and follow the surface rather than cutting across it.
Start at the outer edge of the tread on one side and finish at the outer edge on the other side. Mark the string at both points and keep the line straight across the face of the tire. The distance between the marks is your tread width.
Take the tread measurement at several places around the tire. Tread blocks and grooves can make the edge hard to locate at one spot. Where readings differ, note the range rather than trusting a single pass.
Measuring sidewall width with string
Sidewall width is the distance across the tire at its widest point, measured from sidewall to sidewall. This figure describes the tire's overall width rather than the contact surface. It is the measurement people often want when comparing a tire to a wheel or a fender gap.
Run the string across the tire at the widest part of the sidewall and hold it level. Mark the string where it meets each sidewall edge. The sidewall bulges outward, so the widest point may sit below the shoulder rather than at the tread.
Keep the string square to the tire when you measure sidewall width. A line that runs at an angle across the sidewall reads longer than the true width. Repeat the pass on the opposite side of the tire to check the figure.
Reading the marked string on a tape measure
Lay the marked string flat against a measuring tape to read the distance between the two marks. Keep the string straight and free of loops so the span matches what it was on the tire. Read the tape at the second mark while the first mark sits at zero.
Tire width in millimeters is the figure most tire markings use, so convert if your tape reads in inches. One inch equals about twenty-five millimeters, which is enough precision for comparing a measurement to a sidewall number. Write the result down before the string moves.
Check the reading twice, because a stretched or twisted string shifts the marks. Hold the string against the tape with light tension and look straight down at the scale. A reading taken from an angle can be off by a visible amount.
Keeping the string measurement accurate
Accuracy in string measuring depends on the string staying straight and the marks staying put. Store the marked string flat until you read it, and avoid pulling it through your fingers where the marks can smear. A second person helps hold the tape steady.
Take three passes at the same span and compare the results. Small differences come from the tire surface and the pen line, while a large gap points to a slipped mark or a loose string. Use the repeated figure that matches the others.
String will not replace a proper width gauge for precise work on a wheel or alignment job. A trained technician has tools that read the tire and wheel directly. Use the string method for a household check and leave precision fitting to a specialist.
Checking your figure against the sidewall
The numbers molded into the sidewall give a reference for your string measurement. The first number in a size such as 225/45R17 is the nominal section width in millimeters. Compare your sidewall width reading to that figure and expect some difference.
Nominal section width is measured on a specified rim width, so a tire mounted on a different rim can measure wider or narrower. Tread width is not printed on the sidewall and must be measured. Use the sidewall marking as a guide, not as an exact match for your string reading.
If your reading is far from the sidewall figure, check the units and the marks before blaming the tire. A tape read in inches and recorded as millimeters explains many mismatches. Re-measure, then decide whether the difference is real.
Questions About String Tire Measurement
Can I measure tire width with string instead of a tape measure?
Yes, string can stand in for a tape measure when you mark the span and read it against a tape afterward. String follows the curved tire surface, which a stiff tape cannot do alone. You still need a measuring tape to read the marked distance.
How do I mark the string on the tire correctly?
Mark the string at both edges of the span while it is still held against the tire. Use a fine-tip pen so each mark stays narrow and easy to read. Check that both marks sit at the exact edges before lifting the string.
Is tread width the same as sidewall width on a tire?
No, tread width covers only the running surface, while sidewall width spans the tire at its widest point. Sidewall width is larger on a mounted tire because the sidewalls bulge outward. Each figure answers a different question about the tire.
How do I convert my string measurement to tire width in millimeters?
Multiply an inch reading by about twenty-five to get tire width in millimeters. If your tape already reads in millimeters, no conversion is needed. Record the figure and compare it to the nominal section width on the sidewall.
What kind of string should I use to measure a tire?
A non-stretchy string such as cotton twine holds its length under light tension. Elastic cord stretches and makes the marked span longer than the true width. Thin cord also presses closer to the tire surface than thick rope.