# Measuring Tire Tread Depth with a Coin

Learn how to measure tire tread depth with a penny, quarter, dime, nickel or Canadian coin, what each coin reading means, and when a gauge is the better check.

A coin gives you a quick tread depth reading when no gauge is at hand. You push the coin into a tread groove and read how much of the design stays hidden. The coin test shows whether the tire is above or below a known depth, not an exact number. 

- Place the coin in a groove with the head or design upside down, then see which part stays covered by rubber.
- The penny test flags a tire at the 2/32 inch minimum, the point where tread is worn out.
- The quarter test checks for 4/32 inch, a depth that warns you about wet-weather grip before the legal limit.
- Coins from Canada and the United Kingdom work the same way once you know the depth their design marks.
- A tread depth gauge gives an exact figure and covers the whole tread face better than any coin.
 

## How the coin method works 

The coin method turns a coin into a simple depth reference by using the distance from its edge to a feature on its face. You insert the coin into a tread groove with that feature facing you and the tire rubber closing over it. The amount of the face that stays visible tells you the remaining depth. 

Inserting a coin into tread grooves needs the tire clean and the groove free of stones or grit. Work on one groove at a time and keep the coin flat against the tread rib, not tilted. A tilted coin reads deeper than the groove really is. 

The coin test is a pass or fail check against one depth, not a measuring instrument. Each coin answers a single question about the groove you picked. If you need the exact [tread depth in 32nds](/articles/tire-tread-depth-32nds-to-millimeters-material-46553/) of an inch or in millimeters, use a gauge instead. 

## The penny test and the 2/32 inch minimum 

The penny test is the familiar way to measure tire tread depth with a coin against the 2/32 inch minimum tread. You place a Lincoln head penny into the groove with Lincoln's head upside down and pointing toward the tire. If the top of his head stays visible, the groove is shallower than 2/32 inch. 

A tire at or below 2/32 inch tread depth has reached the wear limit for safe use on wet roads. Water cannot escape from under a tread that shallow, so the tire loses grip sooner. Replace a tire that fails the penny check rather than waiting for the next inspection. 

The penny rule for tire tread works because the distance from the coin rim to the top of Lincoln's head is close to 2/32 inch. A [tire tread wear indicator](/articles/checking-tread-wear-with-wear-indicator-bars/) bar inside the groove gives the same warning. When the rubber sits level with those bars, the tire is worn out. 

## The quarter test for 4/32 inch 

The quarter test checks a deeper limit and gives you warning before the tire reaches the minimum. You insert a Washington head quarter into the groove with Washington's head upside down. If the top of his head is covered, the groove holds more than 4/32 inch tread depth. 

A reading below 4/32 inch means wet grip is dropping, even though the tire still passes the legal minimum in places that set one. Rain and standing water need deep grooves to clear the contact patch. Plan a replacement once the quarter test fails. 

The penny and quarter method pairs the two checks in one walk around the car. The quarter shows the margin you have left, and the penny shows the point where tread is gone. Run both on the same grooves so the two readings describe the same wear. 

## Dime, nickel and other US coins 

The dime test uses the distance from the dime rim to the top of the torch or Roosevelt profile as a shallower reference. Measuring tread depth with a dime lets you flag a groove that is close to the wear limit before the penny fails. The nickel test follows the same idea with the distance to the top of Jefferson's head. 

Coin designs change over the years, and the depth each one marks depends on the specific design on the face. Compare the coin against a ruler once, so you know the depth your coin stands for. Do not assume two coins of the same value carry the same reference. 

These coins work as a [tire tread depth gauge](/articles/choosing-and-buying-a-tire-tread-depth-gauge-start-with-the-sidewall-numbers/) alternative for a quick tread check at the curb. They cannot tell you the depth in 32nds across the whole tread. Treat a borderline result as a reason to bring out the gauge. 

## Canadian coins: quarter, loonie and toonie 

A Canadian coin tread check uses the caribou on the quarter, the loon on the loonie or the polar bear on the toonie as its reference. Measuring tread depth with a Canadian quarter works the same way as the US version, with the design turned upside down in the groove. The depth marked depends on the distance from the rim to the top of that design. 

Measuring tire tread depth with a loonie or a toonie uses a larger coin, so check the reference distance before you rely on it. The caribou antlers on the Canadian quarter sit at a different height from the top of Washington's head. Confirm the depth with a ruler or a gauge the first time you use a Canadian coin. 

Canadian coins and US coins are not interchangeable as depth references, even when the sizes look close. The coin test tire depth result is only as good as the reference you measured. Keep one coin in the glovebox and know exactly which depth it marks. 

## The 20p coin check in the United Kingdom 

A tyre tread depth check with a 20p coin uses the raised rim of the coin as its reference. You push the 20p coin into a groove and look at the outer band. If the band stays hidden by rubber, the groove is deeper than the band's height. 

The 20p coin gives a quick tread depth measurement with a coin for drivers who carry no gauge. The band height is a fixed feature, so the same coin gives the same reading each time. A visible band points to a groove that needs a proper measurement. 

Spelling and coin names differ between markets, but the method does not change. Insert the coin, read how much of the reference stays covered, and repeat in several grooves. Convert the result to the depth unit you use if you record it. 

## Where to check and how to read the tread 

Checking tread in several spots gives a true picture of tire tread wear, because a tire rarely wears evenly. Test the outer shoulder, the center ribs and the inner shoulder on each tire. Worn edges or a worn center point to alignment or inflation issues that one reading would hide. 

Run the coin test in the main circumferential grooves, the deep channels that circle the tire. Avoid the small sipes and slots, which are shallower by design. Read each groove at more than one point around the circle to catch flat spots and uneven wear. 

A worn tire check belongs in a routine that includes pressure and visual inspection. Look for cuts, bulges and exposed cords alongside the tread reading. Any of those findings needs a trained tire technician before the car goes back on the road. 

## When a tread depth gauge is the better tool 

A tire tread depth gauge gives an exact reading in 32nds of an inch or in millimeters, which no coin can do. The gauge has a probe that you press into the groove until the collar sits on the tread. You then read the scale or the digital display. 

Tread depth without tools is convenient, but a gauge settles borderline cases and records wear over time. Measuring tread depth with a coin answers whether you passed a limit. A gauge answers how much tread is left and how fast it is going. 

Use the coin for a quick tread check between services and the gauge for record keeping and decisions. Both methods point to the same tread wear indicator bars when a tire is finished. Neither method repairs a worn tire, and neither replaces a professional inspection. 

## Questions about the coin tread test 

### What is the penny test for checking tire tread? 

The penny test is a tread depth check that uses a Lincoln head penny to find the 2/32 inch minimum. You place the penny in a groove with Lincoln's head upside down, and a fully visible head means the tire is worn out. The tire tread wear penny test gives a pass or fail, not an exact depth. 

### How do you check tire tread with a quarter? 

You check tire tread with a quarter by inserting a Washington head quarter into a groove with the head upside down. If the top of Washington's head stays covered, the groove holds more than 4/32 inch tread depth. A visible head means the tire is approaching the wear limit and needs attention. 

### Can I check tread depth with a Canadian coin? 

Yes, a Canadian coin tread check works with the quarter, loonie or toonie once you know the depth its design marks. Measuring tread depth with a Canadian quarter uses the caribou in the same upside-down position as the US test. Confirm the reference distance with a ruler the first time. 

### How does a 20p coin check tyre tread depth? 

The 20p coin check uses the raised outer band of the coin as the reference depth. You push the coin into a groove and look for a visible band above the rubber. A visible band means the groove is shallow and needs a gauge reading. 

### What is the minimum tire tread depth a coin test looks for? 

The 2/32 inch tread depth is the minimum the penny test looks for, and it marks the point where a tire is worn out. The quarter test looks for a deeper 4/32 inch tread depth as an early warning. Both figures come from the coin design, so check the coin you use. 

### Can I measure tire tread depth without a gauge? 

Yes, measuring tread depth without a gauge is possible with a coin, and it gives a fast pass or fail result. The coin test tire depth reading cannot give an exact number across the whole tread. Use a tread depth gauge when you need precise figures or a record of wear.
