# Measuring Bolt Pattern on 5-Lug and 8-Lug Wheels

Learn how to measure a bolt pattern on 5-lug and 8-lug wheels, including bolt circle diameter, PCD, and why the two lug counts take different methods.

Measuring a bolt pattern on a 5-lug wheel means measuring from the center of one lug hole to the far edge of the hole across from it. An 8-lug wheel is simpler: the lug holes sit opposite each other, so you measure straight from the center of one hole to the center of the one across. Both numbers describe the bolt circle diameter, also called PCD. 

- A bolt pattern is written as lug count times bolt circle diameter, such as 5 x 114.3 or 8 x 170.
- On a 5-lug wheel, measure from the center of one hole to the far edge of the opposite hole.
- On an 8-lug wheel, measure from the center of one hole to the center of the hole straight across.
- The bolt circle is an imaginary circle through the lug holes, not the wheel's outer rim.
- Confirm the pattern against the hub or the vehicle's fitment data before buying wheels.
 

## What a bolt pattern number means 

A bolt pattern is the arrangement of lug holes on a wheel, written as two numbers. The first number is the lug count, such as 5 or 8, and the second is the bolt circle diameter. A 5 x 114.3 wheel has five holes sitting on a circle 114.3 millimeters wide. 

The bolt circle diameter is the distance across the circle that passes through the centers of the lug holes. This figure is also called PCD, or pitch circle diameter, in European catalogs. Lug spacing and bolt spacing describe the same circle from a different angle. 

The lug count only tells you how many studs the hub has. The diameter tells you how far apart those studs sit. Two wheels with five lugs can have different diameters, so the full pattern number is what identifies a fit. 

## Measure across the lug holes on a 5-lug wheel 

A 5-lug [bolt pattern measurement](/articles/how-to-measure-wheel-bolt-pattern-lug-count-and-bolt-circle-diameter/) starts by finding the imaginary circle through the five holes. Measure from the center of one lug hole to the far edge of the hole most directly across from it. The far edge, not the near edge, gives the bolt circle diameter. 

Pick any hole and look across the hub. On an odd lug count, the hole directly across sits slightly off the center line, so the distance runs from a hole center to the opposite hole's outer edge. A tape measure or a caliper held flat across the face of the wheel works well here. 

Repeat the measurement on a second pair of holes to check it. If the two readings differ, the tape was not held through the true center of the holes. A steady, centered reading is what you want before you write the number down. 

## Measure 8-lug wheels hole to hole 

An 8-lug bolt pattern is the straightforward case because every hole has a true opposite. Measure from the center of one lug hole straight across to the center of the hole on the other side. The lug-to-lug distance equals the bolt circle diameter. 

No edge correction is needed on an even lug count. The two holes sit on opposite ends of the same diameter line, so center to center is the same as across the circle. A rigid straightedge laid over the hub helps keep the tape on that line. 

Take the reading on a second pair of holes as a cross-check. A consistent figure confirms the measurement passed through the center. On an 8-lug wheel, two matching readings give you confidence in the number. 

## Why 5-lug and 8-lug need different methods 

The difference comes down to odd and even lug counts. An 8-lug wheel has holes paired directly across the circle, so the tape can run center to center. A 5-lug wheel has no hole directly opposite, so the measurement shifts to the far edge of the opposite hole. 

This odd lug count rule is easy to get wrong and produces a figure that is too small. Using center-to-center on a 5-lug wheel understates the bolt circle diameter. The far edge correction accounts for the missing half of the hole on the far side. 

Both methods describe the same geometry, the circle through the hole centers. The method changes, the definition does not. Once you know the lug count, you know which method to use. 

## Tools and steps for a clean reading 

A tape measure, a caliper, and a straightedge cover most bolt circle measurements at home. A caliper gives a sharper reading on small holes. A straightedge laid across the hub keeps the tape from wandering off the center line. 

Clean the wheel face first so the hole edges are visible. Measure the diameter of one lug hole, then use it when you measure to the far edge on a 5-lug wheel. Note the number in both millimeters and inches, because wheels are listed in either unit. 

Write the lug count and the diameter together as one pattern number. Compare that number with the hub or the vehicle's fitment data before you buy. A measured figure that does not match the hub means the wheel will not seat on the studs. 

## Read the result and check the fit 

The finished measurement is your bolt circle diameter, and the pattern reads as lug count times diameter. For example, five holes on a 114.3 millimeter circle reads as 5 x 114.3. Eight holes on a 170 millimeter circle reads as 8 x 170. 

Check the wheel's center bore and offset as well, because a matching bolt pattern alone does not guarantee a fit. The center bore must clear the hub, and the offset must keep the tire inside the bodywork. A trained specialist should confirm clearance and torque settings on a vehicle. 

Do not force a wheel onto studs that do not line up. A mismatched pattern can damage the studs, the hub, or the wheel. If two measurements disagree, remeasure before you trust either figure. 

## Mistakes that give a wrong bolt pattern 

The frequent error on a 5-lug wheel is measuring center to center instead of center to far edge. That reading comes out smaller than the true bolt circle diameter. Checking the method against the lug count catches this mistake. 

A tape held off the center line is another source of error. The tape must pass through the middle of both holes. Comparing two pairs of holes shows whether the line was true. 

Mixing units causes quiet errors, since a figure in inches and a figure in millimeters look very different. Convert one into the other before you compare. A pattern that seems close but not exact is a different pattern. 

## Bolt Pattern Measurement Questions 

### How do you measure a 5 lug bolt pattern? 

You measure from the center of one lug hole to the far edge of the hole across from it. The far edge matters because a 5-lug wheel has no hole directly opposite. The result is the bolt circle diameter for that wheel. 

### How do you measure an 8 lug bolt pattern? 

You measure from the center of one lug hole to the center of the hole straight across the hub. An 8-lug wheel has holes paired on opposite sides, so center to center equals the bolt circle diameter. A second pair of holes confirms the reading. 

### How do you measure the bolt pattern on a 5 lug rim? 

Lay a tape across the face of the rim through the center and read from one hole center to the opposite hole's far edge. A caliper or straightedge helps keep the line centered. Repeat on another pair before you record the number. 

### What is the difference between lug spacing and bolt circle diameter? 

Lug spacing is the distance between lug holes, while bolt circle diameter is the width of the circle through all the hole centers. Bolt circle diameter, or PCD, is the number written after the lug count in a pattern. Lug spacing is a way of describing part of that same circle. 

### Can two wheels with 5 lugs have different bolt patterns? 

Yes, the lug count alone does not fix the pattern. Two 5-lug wheels can sit on circles of different diameters, such as 5 x 100 and 5 x 114.3. The full pattern number with the diameter identifies the fit. 

### Why is the measurement to the far edge on odd lug counts? 

An odd lug count has no hole directly opposite another hole, so a center-to-center line misses the true diameter. Measuring to the far edge of the opposite hole completes the circle. Even lug counts like 8 do not need this correction.
