How to Use a Pen-Style Tire Pressure Gauge

A step-by-step guide to reading tire pressure with a pen gauge: seating it on the valve stem, reading the scale, bleeding air, and checking tires cold.

9 min read1 viewsHow to Use a Pen-Style Tire Pressure Gauge
— · 0 votes
Contents
  1. What a pen gauge measures
  2. Find the valve stem and remove the cap
  3. Press the gauge onto the stem
  4. Read the pressure scale
  5. Check tires cold for a true reading
  6. Add air or bleed it off
  7. Store the gauge and cap the stem
  8. Compare a pen gauge with other gauges
  9. Pen-Style Tire Pressure Gauge Questions
  10. How do I use a pen-style tire pressure gauge?
  11. Why does my pen gauge give different readings each time?
  12. Should I check tire pressure hot or cold?
  13. What unit does a pen gauge show?
  14. What is the bleed valve on a pen gauge for?
  15. Is a pen gauge as accurate as a digital gauge?

A pen-style tire pressure gauge reads pressure when you press its chuck squarely onto the valve stem and let the sliding scale pop out. You hold the barrel straight, push once, then read the number at the edge of the sliding rod. Releasing the gauge resets it, so each tire needs its own firm press.

  • Press the gauge straight onto the valve stem so the chuck seals on the pin.
  • Read the pressure scale at the end of the sliding rod, not the rod tip.
  • Check tires cold, before driving, or the heat from driving raises the reading.
  • Use the bleed valve to release air if the tire is over the target pressure.
  • Seat the valve cap back on every stem after the check.

What a pen gauge measures

A pen gauge is a small handheld tool that measures the air pressure inside a tire. The pressure scale shows the reading in pounds per square inch (psi) or in bar, depending on the model. The sliding rod inside the barrel moves outward as pressure pushes against it.

The pen gauge measures the pressure the air exerts, not the size of the tire or the depth of the tread. A tire's correct pressure comes from the vehicle maker, often printed on a label on the driver door jamb or in the owner's manual. The number on the tire sidewall is a maximum, not a target for everyday driving.

A pen gauge is a mechanical tool, so it needs no battery and gives a reading the moment you press it. The gauge stores no memory, so you must note each number yourself. A gauge that has been dropped or left dirty may read low, so compare it against another gauge if readings look wrong.

Find the valve stem and remove the cap

The valve stem is the small rubber or metal tube that sticks out through the wheel. A valve cap covers the stem to keep dirt and moisture out of the valve core. Unscrew the cap with your fingers and keep it somewhere clean, such as your pocket.

The valve core sits inside the stem and holds the air in. Do not press the core with a tool or your nail, because the tire will lose air. Look at the stem opening and wipe away grit so it does not get pushed into the valve when you attach the gauge.

On some wheels the stem is short or angled, and reaching it may need a little care. Move the gauge straight in line with the stem rather than at an angle. If a valve cap is cracked or missing, fit a new one after the check so the core stays protected.

Press the gauge onto the stem

Push the chuck of the pen gauge squarely over the valve stem in one firm motion. The chuck is the open end that seals against the stem and opens the valve core. A straight press seats the seal and gives a clean tire pressure reading.

Hold the barrel in line with the stem and avoid tilting it while it is seated. A tilted chuck leaks air around the seal and the rod stops short of the true pressure. One firm press is enough, because repeated pressing with a leaking seal only wastes air.

Listen for a short hiss as you press, which means air is moving through the gauge. A long, steady hiss points to a poor seal, so lift the gauge and seat it again. When the chuck is sealed, the sliding rod extends and holds its position.

Read the pressure scale

The pressure scale is the numbered markings printed on the sliding rod or the barrel. Read the number where the end of the sliding rod meets the barrel edge, not the very tip of the rod. Each mark stands for a set pressure step, and the markings tell you the unit.

Most pen gauges show a dual scale, with psi on one side and bar on the other. Read the unit you plan to compare, and keep using that unit for every tire. If the maker's label lists bar, do not mix it with a psi reading from the same gauge by mistake.

Write the reading down as you go, because the rod resets when you release the gauge. Repeat the press once to confirm the number if the first reading looks off. Two presses that agree give you a tire pressure reading you can trust for that tire.

Check tires cold for a true reading

Tire pressure should be checked when the tires are cold, before the vehicle has been driven far. Driving warms the air inside, and warm air expands, so a hot tire shows a higher reading. A cold reading is the one to compare with the maker's target pressure.

Morning, before the first trip, is a simple time to check, and a shaded spot keeps the sun from heating one side of the car. Air also contracts in cold weather, so a tire set in warm conditions may read low in winter. Adjust the air to the target while the tire is cold.

Check all four tires, plus the spare if the vehicle carries one, and note each number. Uneven numbers across the tires point to a slow leak or a valve problem worth a closer look. A tire that keeps losing pressure after a top-up should be checked by a tire technician.

Add air or bleed it off

If the reading is below the target, add air at an inflator and recheck with the pen gauge. Inflate in short bursts and measure after each burst, because a pen gauge only shows the pressure it is given. Stop when the cold reading matches the maker's number for that tire.

If the reading is above the target, the bleed valve on the gauge lets you release a little air. The bleed valve is a small button on the side of the barrel that opens the gauge to the air. Press it briefly, then reseat the gauge on the stem to read the new pressure.

Never deflate a tire by pressing the valve core with a key or a stick, because the core can bend or the air can escape too fast. Work in small steps and recheck after each one. Over-inflation and under-inflation both affect how a tire wears and handles.

Store the gauge and cap the stem

Fit the valve cap back on the stem after every check to keep dirt and moisture away from the core. Screw the cap on by hand until it is snug, without forcing it. A missing cap is a simple cause of a slow leak over time.

Keep the pen gauge in a clean, dry place, such as the glovebox or a tool tray. Dirt on the chuck can stop it sealing, so wipe the end after use. A gauge that reads the same tire differently on repeated presses may need cleaning or replacing.

Check the gauge against another gauge now and then, since a mechanical tool can drift after a drop. Store the gauge away from heavy items that could bend the barrel or the rod. A straight, clean gauge gives the most reliable tire pressure reading you can get from a pen tool.

Compare a pen gauge with other gauges

A pen gauge is compact and gives a quick reading, but the sliding rod can be hard to read in low light. A digital gauge shows the number on a screen and resets on its own. A dial gauge has a round face and a needle that holds the reading until you release it.

A gauge with a flexible hose is easier to seat on a stiff or deep valve stem. A clip-on chuck holds itself on the stem and frees a hand to note the number. Each type has trade-offs in size, cost and how easy it is to read in poor light.

Whichever gauge you use, its accuracy matters more than its style. Compare your gauge with one known to read a set pressure, such as at a tire shop, before you rely on it for setting pressures. Ask a technician to check the gauge if readings seem inconsistent.

Pen-Style Tire Pressure Gauge Questions

How do I use a pen-style tire pressure gauge?

A pen-style tire pressure gauge is used by pressing its chuck straight onto the valve stem in one firm motion. The sliding rod extends and you read the number where the rod end meets the barrel. Release the gauge, note the reading, then repeat once to confirm it.

Why does my pen gauge give different readings each time?

A pen gauge gives different readings when the chuck does not seal squarely on the valve stem. Tilted or loose seating lets air escape and the rod stops short of the true pressure. Wipe the chuck clean and press straight again, and replace the gauge if readings still disagree.

Should I check tire pressure hot or cold?

Tire pressure should be checked cold, before the vehicle has been driven far. Warm air from driving expands and raises the reading, so a hot check overstates the pressure. Compare cold numbers with the target pressure on the vehicle label.

What unit does a pen gauge show?

A pen gauge often shows two units, psi (pounds per square inch) and bar, on opposite sides of the scale. Read the side that matches the unit on the vehicle's pressure label. Keep using that same unit for every tire so the numbers stay comparable.

What is the bleed valve on a pen gauge for?

The bleed valve releases air so you can lower the pressure in an over-inflated tire. Press the small button briefly, then reseat the gauge on the valve stem to read the new number. Work in small steps and recheck after each release.

Is a pen gauge as accurate as a digital gauge?

A pen gauge can be accurate when it is clean, undamaged and read carefully on a level scale. A digital gauge is easier to read and resets by itself, which reduces reading errors. Check any gauge against a known pressure if you need confidence in its numbers.

Read next

Latest articles