How to Measure Tire Dimensions

Learn how to measure tire dimensions yourself: read the sidewall markings, then check width, overall diameter and tread depth with a tape, ruler or caliper.

10 min read0 viewsHow to Measure Tire Dimensions
— · 0 votes
Contents
  1. Read the sidewall markings before measuring
  2. Tools for measuring a tire at home
  3. Measure section width and tread width
  4. Measure overall diameter and height
  5. Calculate size from the sidewall numbers
  6. Match the method to the tire type
  7. Handle used, mounted and unmounted tires
  8. Convert measurements and check fit
  9. Tire Measurement Questions
  10. How do I measure tire size in mm?
  11. Can I measure tire width in inches?
  12. How do I measure tire height?
  13. What is the difference between section width and tread width?
  14. How do I measure a tire with a caliper?
  15. Do I need to inflate a tire before measuring it?

You measure tire dimensions in two ways: read the size markings on the sidewall, then confirm them with a tape measure, ruler or caliper. The markings give section width, aspect ratio and rim diameter in a standard format. A physical check gives you actual width, overall diameter and tread depth, which is what a used or unmarked tire needs.

  • Read the sidewall first, because the numbers give you a starting size before you touch a tool.
  • Measure section width across the widest part of the inflated tire, not across the tread.
  • Measure overall diameter from the ground to the top of the tire on a mounted wheel.
  • Use a tape for large dimensions and a caliper for tread depth or small gaps.
  • Inflate a mounted tire to its normal pressure before measuring, and measure an unmounted tire at its natural shape.

Read the sidewall markings before measuring

A tire sidewall carries a size code that gives you the three base numbers for any measurement job. A metric code such as 225/45R17 means a section width of 225 millimeters, an aspect ratio of 45 percent and a rim diameter of 17 inches. P-metric and LT markings add a load and use prefix that tells you the tire category.

Metric and inch sizes are written differently, so check which format you have before you pick up a tape. Metric tires show width in millimeters and the aspect ratio as a percentage of that width. Inch sizes on trailer and off-road tires often show a diameter and a width in inches, such as 31x10.5R15. The sidewall tells you the format, so read it fully.

The sidewall numbers are nominal values, which means the tire is built to a range rather than an exact figure. A measured section width can differ slightly from the number on the sidewall. Treat the marking as your reference and your tools as the check against it.

  • Section width: the widest point of the inflated tire in millimeters
  • Aspect ratio: sidewall height as a percentage of section width
  • Rim diameter: the wheel size the tire fits, in inches
  • Construction letter: R for radial, which most car tires use

Tools for measuring a tire at home

A flexible tape measure, a rigid ruler and a caliper cover most tire measurement at home. A tape follows the curve of the tire for width, a straight ruler works for diameter across a flat surface, and a caliper reads small distances such as tread depth. A caliper measurement is more precise than a tape for a narrow gap.

Mark your measuring points with chalk or tape marks so you measure the same place twice. A tread centerline mark helps you keep the tape square across the tire. Without reference points, a second reading can land on a different part of the tire and give a different number.

Keep the units straight, because tire data mixes inches and millimeters. Measure in one unit and convert at the end to avoid a wrong figure. Knowing how to measure tire size in mm means knowing that the width on a metric sidewall is already in millimeters.

  • Flexible tape measure for section width and overall diameter
  • Rigid ruler for tread width and a quick diameter check
  • Caliper for tread depth and small gap readings
  • Chalk or tape to mark your measuring points

Measure section width and tread width

Section width is the distance across the tire at its widest point, measured from sidewall to sidewall. Lay the tape across the inflated tire at the widest bulge, square to the tread centerline. Read the number where the tape meets the far sidewall and note it in millimeters or inches.

Tread width is narrower than section width because it covers only the part of the tire that touches the road. Measure tread width across the flat running surface from shoulder to shoulder. The difference between tread width and section width is the sidewall bulge on each side.

For how to check tire width on a mounted tire, inflate to the normal pressure first, because pressure changes the bulge and the reading. A tire measured flat will read wider at the sidewall than one at running pressure. Check your width against the sidewall section width to see how close the two figures are.

MeasurementWhere to place the tapeWhat it tells you
Section widthWidest point, sidewall to sidewallOverall tire width at the bulge
Tread widthShoulder to shoulder on the running surfaceWidth of the road contact area
Sidewall heightRim edge to tread edgeHeight of the tire side above the wheel

Measure overall diameter and height

Overall tire diameter is the full height of the tire from the ground to the top on a mounted wheel. Park on level ground and place a straight edge across the top of the tire. Measure from the ground to that edge to get the overall height in one reading.

An unmounted tire needs a different approach, because it does not sit as a circle on its own. Stand the tire upright and measure across the face from the outer edge of the tread on one side to the other. Take two readings at right angles and use the larger one as the diameter.

You can check the diameter against the sidewall numbers using an overall diameter calculation. Multiply the section width by the aspect ratio, divide by 100 for sidewall height, double it, then add the rim diameter in the same unit. A measured diameter that differs from the calculation points to wear, pressure or a different size than marked.

Calculate size from the sidewall numbers

How to calculate tire dimensions starts with the sidewall code, and the aspect ratio formula does the work. Sidewall height equals section width multiplied by the aspect ratio, divided by 100. A 225/45 tire has a sidewall height of about 101 millimeters.

Overall diameter in mm comes from doubling the sidewall height and adding the rim diameter converted to millimeters. One inch equals 25.4 millimeters, so a 17 inch rim is about 432 millimeters across. The total gives you the height the tire stands at on the wheel.

Use the calculation as a reference, then confirm it with a measurement. Tire wear removes tread material and changes the measured diameter, so a worn tire reads smaller than the formula. Comparing measured dimensions with markings tells you whether the tire matches its label.

  • Sidewall height = section width x aspect ratio / 100
  • Overall diameter = (sidewall height x 2) + rim diameter in the same unit
  • Rim diameter in mm = rim inches x 25.4
  • Rolling circumference = overall diameter x pi, for distance per turn

Match the method to the tire type

Unfamiliar tire types need a check on the format before you measure. Trailer tires often use inch sizes, commercial van tires use load-rated metric codes, and off-road tires may use a flotation size in inches. Each format tells you which dimension is written first, so read the code before choosing a tool.

Oversized tire measurement needs more room and a second pair of hands for a steady tape. Measure section width at the widest point and overall height with the tire standing free. For RC tires, the method is the same in principle but at a much smaller scale, and a caliper gives a better reading than a tape.

Shipping and cover fit both need the outside dimensions of the tire, not the rim size. For how to measure a tire for shipping, note the overall diameter, section width and weight. Tire cover fit measurement uses overall diameter plus a small allowance, and spare tire cover dimensions follow the same rule.

Handle used, mounted and unmounted tires

Used tire measurements should include tread depth along with width and diameter. A depth gauge or a caliper at the tread grooves gives the remaining tread. A worn tire measures smaller in diameter than a new one of the same size, so record both the size code and the physical readings.

A mounted tire measurement is taken at normal inflation pressure, with the vehicle on level ground. Release no air for the reading, because a soft tire gives a false width and height. Mark the sidewall position of your tape so you can repeat the check later.

An unmounted tire sits relaxed, so measure it free-standing and not leaning on a wall. Check the bead area for damage before you press a tape against it. Any tire with cuts, bulges or exposed cords should go to a trained technician rather than be measured and refitted.

  • Inflate a mounted tire to its normal pressure before reading
  • Record tread depth on a used tire along with size
  • Stand an unmounted tire upright and support it
  • Route damaged tires to a trained technician instead of refitting

Convert measurements and check fit

The last step compares your measured figures with the size you need, in one unit. Converting mm to inches is a division by 25.4, and inches to mm is a multiplication by the same figure. Keep the decimal places and round only at the end so the comparison stays fair.

Fit checks use section width for clearance to suspension and body, and overall diameter for speedometer and gearing changes. A tire that is wider or taller than the original can rub when the wheel turns or the suspension compresses. Measure the space around the mounted tire before you change size.

The tire diameter and width measurement together give you the full picture for maintenance, shipping or a replacement. Write both numbers down with the unit and the date. Clear notes make a repeat measurement quick and let a technician confirm your figures.

Tire Measurement Questions

How do I measure tire size in mm?

Measure the section width across the widest point of the inflated tire and read the tape in millimeters. The sidewall code on a metric tire already lists width in millimeters, so you can compare your reading with the marking. Overall diameter in mm is the height from the ground to the top of the tire.

Can I measure tire width in inches?

Yes, you can measure tire width in inches with a tape that has an inch scale. Place the tape across the widest part of the sidewall and read the inches directly. To compare with a metric sidewall number, multiply the inches by 25.4 to get millimeters.

How do I measure tire height?

Tire height, or overall diameter, is measured from the ground to the top of the tire on a mounted wheel. Use a straight edge across the top and read down to the ground. An unmounted tire is measured across its face from tread edge to tread edge.

What is the difference between section width and tread width?

Section width is the widest point of the tire from sidewall to sidewall. Tread width covers only the running surface between the shoulders. Section width is always the larger figure because it includes the sidewall bulge.

How do I measure a tire with a caliper?

A caliper suits small readings such as tread depth at the grooves or the gap between tread blocks. Open the jaws across the distance you want and close them gently on the surface. For width or diameter, a tape or ruler reaches farther and stays square.

Do I need to inflate a tire before measuring it?

A mounted tire should be at its normal running pressure before you measure width or height. Pressure changes the sidewall bulge and the standing height. An unmounted tire is measured free-standing at its natural shape.

Latest articles