How to Measure Rear Hub Spacing and Hub Width
Learn to measure rear hub spacing and hub width with a caliper, read the over-locknut dimension, and tell quick-release from thru-axle frames.
Contents
- Spacing and width are two different numbers
- Tools and preparation before measuring
- Measuring rear hub spacing at the dropouts
- Measuring hub width across the locknuts
- Reading the caliper in millimeters
- Quick-release and thru-axle hubs compared
- Matching a wheel to a frame
- Recording your measurements
- Rear hub spacing questions
- How do you measure rear hub width?
- How do you measure rear hub spacing on a frame?
- Can I use a ruler instead of a caliper?
- Does hub spacing tell me the axle type?
- What if the hub width does not match the frame spacing?
- Should rear hub measurements be in millimeters or inches?
Rear hub spacing is the distance between the two inner faces of the frame dropouts, and hub width is measured across the hub locknuts. You measure the first with the wheel out of the frame and a caliper or ruler, and the second with the wheel removed and the locknuts as your reference points. Both numbers are read in millimeters and should match before a wheel goes into a frame.
- Rear hub spacing is a frame measurement, taken between the dropout faces with the wheel out.
- Hub width, or the over-locknut dimension, is the locknut-to-locknut distance across the axle.
- Read both figures in millimeters and note the axle type before ordering or swapping a wheel.
- A quick-release hub and a thru-axle hub sit in different frames, so spacing alone does not confirm fit.
- Use a caliper for a reliable reading, and have a trained mechanic check a frame that looks bent.
Spacing and width are two different numbers
Rear hub spacing belongs to the frame, not to the wheel. The figure describes the clear distance between the inner faces of the two dropouts that hold the axle. A mechanic measures spacing with the rear wheel removed, so nothing spreads or compresses the frame.
Rear hub width belongs to the wheel and is also called the over-locknut dimension. The measurement runs from the outer face of one axle locknut to the outer face of the other. Hub spacing and hub width are designed to match, yet each is measured on a different part.
Mixing up the two figures leads to a wheel that will not sit straight or a frame that must be forced apart. Label each reading as spacing or width before you compare it with a standard. Millimeters vs inches also matters here, because frame and hub standards are written in millimeters.
Tools and preparation before measuring
A caliper gives the cleanest reading of rear hub width and dropout spacing. A digital or dial caliper with jaws wide enough for the hub body works well. A steel ruler or tape measure can serve as a rough check, but its reading is easier to misplace.
Clean the dropouts and the locknuts before you start, since dirt adds to the number you read. Remove the rear wheel and set the bike upright so the frame is not twisted. Let the caliper jaws touch the surfaces lightly instead of pressing them into the metal.
Write each number down as you take it, including the axle type you see. A second reading taken a few minutes later confirms the first. If the frame looks bent or the dropouts are uneven, stop and let a trained mechanic inspect it.
Measuring rear hub spacing at the dropouts
Rear dropout spacing is measured between the inner faces of the frame where the axle seats. Open the caliper jaws and place each jaw flat against one dropout face. Read the distance across the gap without letting the jaws tilt.
Quick-release and thru-axle hub spacing differ in how the axle sits, yet the spacing figure is still taken at the dropout faces. On a thru-axle frame, the dropout has a hole and a slot for the axle; measure between the inner faces around that hole. Do not measure across the outer shell of the frame.
Take the reading at the point where the axle actually rests, not at the widest part of the dropout. A frame with horizontal dropouts can give a slightly different figure depending on where the axle sits in the slot. Note that position if the frame allows the wheel to move forward or back.
Measuring hub width across the locknuts
Hub width, or the locknut-to-locknut distance, is measured with the wheel out of the frame. Set the wheel on a flat surface and find the two locknuts that sit against the frame faces. Place the caliper jaws on the outer faces of those locknuts.
Read the over-locknut dimension straight across the axle, keeping the caliper square to the hub. On a quick-release hub, the skewer passes through the axle but the locknuts still define the width. On a thru-axle hub, the end caps or axle ends take the place of the locknuts, so measure across those faces.
Check that the caliper jaws sit on the locknut face rather than on a dust cover or a spacer. A spacer left in place changes the reading and makes the hub seem wider. Measure twice and compare the result with the spacing you took from the frame.
Reading the caliper in millimeters
Rear hub spacing and hub width are stated in millimeters, so set the caliper to that scale first. Read the main scale, then add the smaller divisions shown on the sliding jaw. Write the number down with the unit, for example 135 mm, so the figure cannot be confused later.
Millimeters vs inches causes errors when a frame figure is converted and rounded. A conversion from inches introduces small differences that matter when a hub must fit a dropout within a fraction of a millimeter. Keep the original millimeter reading and convert only for reference.
Compare your two readings and see how close they sit. A hub width that differs from the frame spacing by more than a small margin signals a mismatch or a measuring error. Recheck the caliper zero and the contact points before you draw a conclusion.
Quick-release and thru-axle hubs compared
A quick-release hub uses a skewer that clamps the axle into open dropouts. A thru-axle hub passes a fixed axle through closed dropouts and threads into the frame or a nut. The two systems hold the wheel in different ways, so the axle type is part of fitment.
Hub spacing can be the same number on a quick-release frame and a thru-axle frame, yet the wheels do not swap. The dropout shape, the axle diameter and the end caps all change the fit. Read the frame and the hub for their axle type before you trust a matching width.
A conversion between the two systems needs the right frame, axle and end caps together. Changing only the hub does not convert a frame from one standard to the other. A trained mechanic should handle a conversion, because the wrong parts can leave the wheel loose.
| Feature | Quick-release hub | Thru-axle hub |
|---|---|---|
| Dropout type | Open slot | Closed hole |
| Axle holding the wheel | Skewer through the hub | Fixed axle through frame |
| Width reference | Locknut faces | End cap or axle faces |
| Spacing check | Inner dropout faces | Inner dropout faces |
Matching a wheel to a frame
A rear wheel fits a frame when the hub width equals the dropout spacing and the axle type matches. Compare the over-locknut dimension with the spacing figure you measured, not with a number from a listing. The two readings should agree within the tolerance the frame and hub were made to.
Spreading or squeezing a frame to accept a wider or narrower hub puts stress on the dropout area. Steel frames tolerate small changes better than other materials, but the job still belongs to a trained mechanic. Aluminum and carbon frames should not be spread by hand at all.
A wheel that sits off-center after fitting points to a spacing or dish problem rather than a tire problem. Check the axle seating and the dropout faces before you adjust anything. If the frame or the hub shows damage, replace the part instead of forcing a fit.
Recording your measurements
A short record of rear hub spacing and hub width saves time when you shop for a wheel or a frame. Note the spacing in millimeters, the hub width in millimeters and the axle type on one line. Add the dropout shape, since an open slot and a closed hole take different wheels.
Keep the record with the bike or in a file you can find later. Measurements taken on a clean, unloaded frame stay useful as a reference. A note of the caliper used also helps you judge how precise the reading was.
Update the record after any change to the frame, the hub or the axle parts. An old figure can mislead when a part has been replaced. A trained mechanic can confirm the numbers during a service visit.
Rear hub spacing questions
How do you measure rear hub width?
Rear hub width is measured across the outer faces of the two axle locknuts with the wheel out of the frame. Place the caliper jaws flat on each locknut face and read the over-locknut dimension in millimeters. On a thru-axle hub, measure across the end cap or axle faces instead.
How do you measure rear hub spacing on a frame?
Rear hub spacing is measured between the inner faces of the frame dropouts with the wheel removed. Set each caliper jaw against one dropout face and read the gap in millimeters. Do not measure across the outside of the frame shell.
Can I use a ruler instead of a caliper?
Yes, a ruler or tape measure can give a rough figure for rear hub spacing or hub width. A caliper reads the faces more precisely, which matters when a hub must fit a dropout closely. Use the caliper reading when the two numbers disagree.
Does hub spacing tell me the axle type?
No, hub spacing alone does not show whether a frame takes a quick-release or a thru-axle hub. Two frames can share the same spacing and still use different dropout shapes and axle diameters. Check the dropout and the hub end caps separately.
What if the hub width does not match the frame spacing?
A mismatch between hub width and frame spacing means the wheel does not belong in that frame as it stands. Do not spread or squeeze the frame by hand to close the gap. Have a trained mechanic assess the frame and the correct hub standard.
Should rear hub measurements be in millimeters or inches?
Rear hub spacing and hub width are written in millimeters, which is the scale frame and hub standards use. Take your reading in millimeters and convert to inches only if you need a reference figure. Keeping the original millimeter number avoids rounding errors.
Read next
-
Boost vs Non-Boost Hubs: Spacing and Compatibility
-
Bicycle Rear Hub Spacing Chart and Standards
-
Bicycle Thru-Axle Adapters: Types and Compatibility
-
Bicycle Thru-Axle Sizes and Dimensions by Bike Type
-
Bicycle Thru-Axle Hex Size: Finding the Right Tool
-
Bicycle Quick-Release Axle Dimensions: Diameter, Length and Hub Spacing