# How to Measure a Mobility Scooter Tire

Measure a mobility scooter tire yourself with a tape measure. Get the outside diameter and tire width right and know what wheel diameter to use for a new tire.

You measure a mobility scooter tire with a tape measure across the outside of the tire, from the tread surface on one side to the tread surface on the other. That outside diameter and the tire width are the two figures you compare with a replacement tire. The wheel diameter, meaning the rim the tire sits on, is a separate figure and comes from the wheel itself or the sidewall marking. 

- Measure the outside diameter across the tread in two directions and keep the larger figure.
- Measure the [tire width from sidewall](/articles/tire-size-markings-width-aspect-ratio-construction-rim-size-material-44540/) to sidewall, not across the tread pattern only.
- Read the sidewall marking first, since it may already give the tire dimensions.
- Measure the bare wheel to get the wheel diameter when the old tire is off.
- A solid tire must match the wheel closely, while a pneumatic tire seats on a matching rim.
 

## Start with the sidewall marking 

A mobility scooter tire often carries a marking on its sidewall that gives the tire dimensions. Read the numbers before you touch the tape measure, because the marking may save you from guessing. The pattern is close to a car tire: a section width and a rim diameter, sometimes with a load or speed code. 

A marking such as 3.00-4 means the tire has a narrow section and fits a wheel about four units across. Larger scooters use markings such as 3.50-8 or 4.00-5, so the numbers do not always match a car tire format. The first figure is the tire width and the second is the wheel diameter, not the outside diameter. 

The marking is the place to start, but it does not replace your own measurement. Wear, a different brand of casing or a previous replacement can make the fitted tire differ from what the marking suggests. Write the marking down, then check it against the tape measure before you order. 

## Measuring the outside diameter 

The outside diameter is the full height of the tire across its center, measured through the wheel. Stand the scooter on level ground and place the tape across the tire face so it passes through the middle of the wheel. Read where the tape crosses the tread surface at both the top and the bottom. 

Take a second reading at a right angle to the first, then keep the larger of the two figures. A wheel can sit slightly off center, and a single reading at one spot can understate the true outside diameter. The larger figure is the one to compare with a replacement tire. 

Read the height of the tire and not the height of the tread block alone, since the outside diameter includes the full tread. A flat pneumatic tire gives a false small figure, so inflate it to its working pressure first. Record the figure in the same unit that the tire seller uses. 

## Measuring tire width and tread 

Tire width is the distance from one sidewall to the other at its widest point, measured with the tire fitted. Lay the tape across the tire at the middle of the wheel and read the outer face of each sidewall. The tread pattern sits inside this figure and does not define the width. 

Measuring tire tread on its own tells you how much rubber sits under the wheel. A tread measurement is useful for checking wear, and it is not the same as the tire width. Keep the two figures separate so you do not order a tire that is too wide for the scooter frame. 

Check clearance to the frame, the fender and the motor before you fit a wider tire. A tire that matches the outside diameter can still rub if its width grows. A tape measure across the fitted tire shows you what space you have to work with. 

## Getting the wheel diameter 

The wheel diameter is the width of the bare rim or wheel, across its center and not around its outside. Measure the wheel with the old tire removed, from one bead seat to the opposite bead seat. This figure is what a tire supplier means by the second number in a size marking. 

A wheel diameter of a few units suits the small wheels on many scooters, and larger scooters carry bigger wheels. The bare wheel figure is smaller than the outside diameter of the fitted tire by roughly twice the tire height. Never substitute the outside diameter for the wheel diameter when you order. 

A solid tire and a pneumatic tire both sit on the same wheel, yet they measure differently once fitted. The wheel diameter stays fixed, while the outside diameter depends on the tire on it. Note both figures on the same sheet so the pair stays together. 

## Solid versus pneumatic tires in the tape measure 

Solid versus pneumatic tires changes how you measure, and each type needs its own check. A solid tire holds its shape, so a tape measure reading is repeatable and easy to trust. A pneumatic tire changes shape with pressure, so inflate it before you measure. 

A pneumatic tire with low pressure reads smaller and wider than it should. Air it to the pressure marked on the sidewall, then take the outside diameter and the width again. A solid tire has no pressure to set, so measure it as it sits on the wheel. 

The two types also differ at the bead, the edge that grips the wheel. A solid tire must match the wheel closely, and forcing one on can damage the wheel or the tire. A pneumatic tire seats on a matching rim and needs a trained technician when the fit is tight. 

## Using a tape measure correctly 

A tape measure gives a good reading on a scooter tire when you hold it square to the wheel. Keep the blade straight across the center and let it touch the tread without pressing into it. A tape held at an angle reads long, and a tape pressed into soft rubber reads short. 

Measure each figure more than once and write down every reading before you compare them. Two readings that agree are stronger than one quick pass around the tire. If the readings disagree, find the reason before you choose a replacement. 

Note the unit on the sheet, since some tires are marked in inches and others in metric figures. Convert only after you have recorded the raw reading. A clear note prevents a mix-up when you take the figures to a supplier. 

## Matching your measurements to a new tire 

A new mobility scooter tire matches when its outside diameter, tire width and wheel diameter all line up with the old one. Compare each figure in turn and treat a mismatch in any of them as a reason to stop. The wheel diameter must match the wheel, and the outside diameter must fit the scooter. 

The table below shows what each figure tells you and what it does not. Use it as a checklist, not as a substitute for the seller's size chart. 

When the figures are close but not exact, ask the tire seller to confirm the fit before you buy. A trained technician should mount a tire that needs force or a special tool. Keep the old tire until the new one is fitted and the scooter rolls freely. 
| Figure | What it tells you | What it does not tell you | 
| Outside diameter | Full height of the fitted tire | The size of the bare wheel | 
| Tire width | Sidewall to sidewall width | The tread depth | 
| Tread measurement | Rubber under the wheel | The tire width | 
| Wheel diameter | Width of the bare wheel | The fitted tire height |  

## Checking the fit after measuring 

A measured tire still needs a check on the scooter before you rely on it. Turn the wheel by hand and watch the clearance to the frame, the fender and the motor. A tire that rubs at any point is the wrong size, even when the numbers matched. 

Check that the tire sits evenly on the wheel and that the tread runs true as the wheel turns. A wobble can come from a tire that is not seated, and it can also come from a bent wheel. Stop and have a trained technician look at either fault. 

Record the final figures on the scooter so the next replacement is quicker. The outside diameter, tire width and wheel diameter are the three numbers that matter. A short note keeps the sizes together for the future. 

## Mobility scooter tire measuring questions 

### How do I measure a mobility scooter tire? 

Measure a mobility scooter tire with a tape measure across the tread to get the outside diameter, then across the sidewalls to get the tire width. Take the outside diameter reading in two directions and keep the larger figure. Write down both figures and compare them with the sidewall marking. 

### Is the outside diameter the same as the wheel diameter? 

No, the outside diameter and the wheel diameter are different figures. The outside diameter is the full height of the fitted tire, while the wheel diameter is the width of the bare wheel that the tire sits on. Order a tire by the wheel diameter, and use the outside diameter to check that it fits the scooter. 

### Should I measure a pneumatic tire flat or inflated? 

Inflate a pneumatic tire to its working pressure before you measure it. A flat tire reads smaller in outside diameter and wider at the sidewall, so the figures will not match a replacement. A solid tire needs no pressure setting and can be measured as it sits. 

### What does the number on a mobility scooter tire sidewall mean? 

The sidewall marking gives the tire width first and the wheel diameter second, in a pattern such as 3.00-4. The first figure is not the outside diameter, and the second figure is not the height of the fitted tire. Check the marking against your own tape measure readings before you order. 

### Can I fit a wider tire on my scooter? 

A wider tire fits only when the scooter has clearance at the frame, the fender and the motor. Measure the space around the fitted tire before you change the width. A trained technician should check the fit when the new tire sits close to any part of the scooter.
