How to Inspect Tire Sidewall Markings
A step-by-step guide to inspecting tire sidewall markings: size, load index, speed rating, DOT date code, and approval marks, plus cracks, bulges, and lighting.
Contents
- Start with a clean, well-lit sidewall
- Walk around in a fixed reading order
- Verify size, load index, and speed rating
- Find and decode the DOT date code
- Check approval and direction markings
- Look for cracks, bulges, and cuts
- Use a checklist for routine and pre-trip checks
- Run the no-tools version on the road
- Tire sidewall marking questions
- What are the essential tire markings to verify?
- What equipment do I need for tire sidewall inspection?
- How do I read faded sidewall markings in the dark?
- How do I inspect tire sidewall markings step by step?
- Should I check tire sidewalls before a long trip or before buying tires?
- What does the DOT date code on the sidewall tell me?
Inspecting tire sidewall markings means reading the molded letters and numbers that state size, load index, speed rating, and manufacturing date, then checking that each is present, matching, and readable. The check also covers the rubber around the markings for cracks, bulges, or cuts that no code can show. A light, clean hands, and a fixed reading order turn the task into a short routine.
- Read the markings in a set order: size, load index and speed rating, then the DOT code.
- Match the size and load figures on the tire to the tire pressure placard on the vehicle.
- Check that the markings are legible; faded or scratched codes hide the facts you need.
- Use an angled light to expose cracks and bulges that a straight-on view flattens out.
- Inspect all four tires, not one, because each sidewall carries its own date and damage history.
Start with a clean, well-lit sidewall
Sidewall marking inspection starts with a sidewall you can actually read, so wash off the worst of the dirt first. Mud and brake dust fill the molded recesses where the codes sit. A wet cloth and a soft brush lift the surface grime without scratching the letters.
Lighting decides how much of the marking you can see, and a raking light at a shallow angle is the key tool. A flashlight or phone light held close to the rubber and nearly parallel to it throws each molded digit into relief. Straight-on light flattens faint stampings and hides the depth difference.
A phone flashlight works for most of the inspection, and a small inspection light adds a tighter beam on the darkest spots. Keep the beam moving slowly across the lettering instead of staring at one point. Contrast against the black rubber makes the difference between a mark you read and one you guess.
Walk around in a fixed reading order
A fixed reading order keeps a sidewall inspection from skipping a marking, and it works the same on every tire. Read the size designation first, then the load index and speed rating, then the DOT code and approval markings. Going in the same sequence each time builds a habit that survives a rushed pre-trip check.
Read the size first because it frames everything else, such as a 205/55R16 format. The load index and speed rating sit near the size on the sidewall and belong to the same information block. Rotate the wheel as you go so each part of the sidewall passes the light in turn.
Both sidewalls carry markings, so check the outer face on the vehicle and the inner face where it shows. Inner sidewalls are harder to see and often carry the same size and date information. A tire mounted with the wrong face outward hides markings the reader needs.
Verify size, load index, and speed rating
Tire size markings on the sidewall give the nominal width, aspect ratio, construction, and rim diameter in one string. The load index is a code for the maximum load the tire can carry at its rated pressure. The speed rating is a letter for the maximum speed the tire is built to sustain.
Verify that the size and load index on the tire match the tire pressure placard on the vehicle door jamb or fuel flap. A mismatch means someone fitted a tire the vehicle was not set up for. The speed rating should meet or exceed what the placard calls for.
Numbers in the size string can sit close together and blur under a weak light. Read each block separately and say it back to yourself before moving on. A magnifying glass helps where the molded figures are shallow or partly worn.
Find and decode the DOT date code
The DOT code ends in a four-digit date code that gives the week and year of manufacture. The first two digits are the week and the last two are the year, so a code ending in 2319 means the twenty-third week of 2019. The full DOT string also identifies the plant and the tire line.
The date code appears on one sidewall only, so you may need to look at both faces or under the vehicle to find it. A code with three digits instead of four points to an older format. Confirm the date on every tire, because a set can mix ages.
Reading faded markings gets harder as the rubber ages, and a shallow date code can disappear under grime. Clean the area and use the angled light before deciding a code is missing. A date you cannot read is a fact you cannot confirm.
Check approval and direction markings
Approval markings show that a tire meets a recognized standard, and they sit alongside the size and date codes. Mounting direction markings tell the fitter which way the tire must rotate, shown by an arrow or the words inside or outside. These markings matter for correct fitting and for later service.
Check that direction markings are present and that the tire sits the right way on the wheel. An arrow pointing the wrong way means the tire was mounted backwards. The words inside and outside belong on the correct face of the wheel.
Approval marks that are scuffed or partly missing leave the tire's standard unclear. Note the gap and treat it as a reason to look closer at the rest of the sidewall. Legibility of every marking is part of the inspection, not an afterthought.
Look for cracks, bulges, and cuts
Sidewall cracks and bulges matter more than any code, because they show damage the numbers cannot record. Cracks follow the flexing area and show as fine lines in the rubber. A bulge is a soft spot where the internal structure has failed.
Run your hand slowly around the sidewall and feel for a step or a soft place, then look at the same spot with the angled light. Shadows from the raking beam make shallow cracks visible that a straight view misses. Check both sidewalls and the bead area where the tire meets the rim.
A bulge or a deep cut needs a trained tire specialist, and the vehicle should not be driven far on that wheel. Do not probe a damaged sidewall with a tool or try to repair it yourself. A sidewall injury is not a job for a roadside fix.
Use a checklist for routine and pre-trip checks
A tire sidewall inspection checklist turns the steps into a repeatable routine for a road trip or a used tire purchase. The same list covers a pre-purchase tire check, where you read the date code and look for damage before money changes hands. Written steps keep the order stable when you are in a hurry.
The checklist should name the size, load index and speed rating, the DOT date code, approval and direction markings, and the damage check. Tick each item only when the marking is clean and readable. A tick you cannot justify under the light is not a pass.
Practice on a spare tire or a scrap tire builds the eye for faint stampings before you rely on the skill. A hands-on practice session on a spare lets you find the date code and read a size string without pressure. The same reading order then carries over to the tires on the vehicle.
Run the no-tools version on the road
A no-tools sidewall reading uses your eyes, hands, and whatever light you carry, and it catches the important facts. Crouch by each wheel and read the size, then the load index and speed rating, then the date code. Feel for bulges with a flat hand as you go around.
A phone flashlight covers the lighting need in a parking area or at the roadside. Hold it low and across the sidewall so the beam rakes the surface. Glare from a bright, direct beam washes out the molded letters, so angle it away from the tire face.
An inspection mirror helps you see the inner sidewall and the date code hidden behind the wheel. A small mirror on a handle reaches the gap between tire and body. Where a mirror shows damage, stop and get the tire checked by a specialist.
Tire sidewall marking questions
What are the essential tire markings to verify?
The essential tire markings are the size designation, the load index and speed rating, the DOT date code, and the approval and direction marks. Each one states a fact about fit, capacity, age, or correct mounting. The sidewall crack and bulge check belongs to the same pass.
What equipment do I need for tire sidewall inspection?
A flashlight or phone light is the main piece of equipment for tire inspection, and a cloth for dirt helps. A magnifying glass and a small inspection mirror reach faded codes and the inner sidewall. No special tools are needed to read the markings themselves.
How do I read faded sidewall markings in the dark?
Reading faded markings in low light works with a raking light held close and nearly parallel to the sidewall. The angled beam casts shadows in the molded recesses and makes each digit stand out. A straight, bright beam creates glare and hides the contrast you need.
How do I inspect tire sidewall markings step by step?
Clean the sidewall, light it at an angle, and read the size first, then the load index and speed rating, then the DOT date code. Check approval and direction markings next and finish with the crack, bulge, and cut check. Repeat the same order on all four tires.
Should I check tire sidewalls before a long trip or before buying tires?
Yes, a sidewall check before a road trip or a used tire purchase shows age, damage, and correct fit before you rely on the tire. The DOT date code and any bulge or crack are the facts to confirm first. A sidewall with a bulge needs a professional check before driving.
What does the DOT date code on the sidewall tell me?
The DOT date code tells you the week and year the tire was manufactured, shown as the last four digits of the DOT string. A code ending in 2319 means the twenty-third week of 2019. The date appears on one sidewall only, so check both faces to find it.