How to Check Spare Tire Size

Learn how to read the spare tire sidewall, measure diameter and width, and compare a spare to the tires already on the vehicle before you fit it.

8 min read0 viewsHow to Check Spare Tire Size
— · 0 votes
Contents
  1. Start with the spare tire sidewall markings
  2. Decode the numbers in the size code
  3. Measure the spare with a tape
  4. Compare the spare to the tires already on the vehicle
  5. Check the wheel, hub and brake clearance
  6. Handle a guest vehicle spare with care
  7. Use the right limits for a temporary spare
  8. Spare Tire Size Questions
  9. How do I check spare tire size without a sidewall code?
  10. Does the spare tire size need to match the road tires?
  11. What is a roadside spare tire size match?
  12. How do I read the load index and speed rating on a spare?
  13. Can I use a different size spare on a guest vehicle?

You check a spare tire size by reading the size code molded on its sidewall, then comparing that code and the measured diameter to the tires on the vehicle. A temporary spare is often narrower and smaller than the road tires, so the match is not exact. The check tells you whether the spare fits the wheel, the hub and the clearance around the brakes.

  • Read the full size code on the spare sidewall, including the load index and speed rating where they appear.
  • Measure the spare diameter with a tape across the tread if the sidewall code is worn or missing.
  • Compare diameter and width to the tires already on the vehicle, not to a guess.
  • Confirm the spare fits the wheel stud pattern and clears the brakes before you rely on it.
  • A temporary spare is for a short trip at reduced speed, not a permanent replacement.

Start with the spare tire sidewall markings

The sidewall of a spare tire carries a size code molded into the rubber, and that code is the first thing to check. A code such as 125/80 D16 splits into a width, an aspect ratio and a wheel diameter. Letters and digits after the size give the load index and speed rating for that tire.

Spare tire markings can be faint on an older tire that has sat in the trunk for years. Wipe the sidewall clean and read the code in good light, working around the circle until you find the block of raised characters. The size code sits next to the brand name and the words that identify the tire as a temporary spare.

Some temporary spares use a letter code instead of the metric format, and that letter identifies the compact size. Write the full code down exactly as molded, because one changed digit alters the dimensions. A photo of the sidewall keeps the code readable when you compare it later.

Decode the numbers in the size code

A metric spare size code gives width in millimeters, aspect ratio as a percentage of width, and wheel diameter in inches. A 125/80 D16 spare is 125 mm wide, has a sidewall height of 80 percent of that width, and fits a 16 inch wheel. The D marks a diagonal or bias construction used on some temporary spares.

The load index and speed rating tell you what the tire can carry and how fast it may turn. A temporary spare carries a lower load index and speed rating than the road tires, and that limit is part of the tire design. Respect those figures when you fit the spare.

Radial road tires use an R in the code, while a temporary spare may use a different letter. Tire diameter and width come straight from the code once you decode it. A size calculator or a printed conversion table turns the code into a diameter in inches.

Measure the spare with a tape

A tape measure check confirms the diameter when the sidewall code is worn, painted over or hard to read. Lay the spare flat and run the tape across the center of the tread from edge to edge. The reading is the overall diameter of the spare tire.

Measure the width by placing the tape across the tread face at its widest point. Compare that number to the tire on the vehicle, because a narrower spare changes how the vehicle tracks. Record both numbers so the comparison stays clear.

A tape measure reads the mounted tire, so the figure can differ slightly from the sidewall calculation. Take the measurement at the tread and not at the sidewall bulge. Repeat the reading at a second point to catch a tape that slipped.

Compare the spare to the tires already on the vehicle

Comparing the spare to existing tires shows how far the spare differs in diameter and width. Read the size code on one road tire and decode it the same way as the spare. Place the two decoded sizes side by side and note the difference in diameter.

A diameter difference changes the rolling circumference, and that affects how the vehicle drives with the spare fitted. Width difference changes the contact patch and the clearance to suspension parts. A temporary spare is built to differ from the road tires, so the comparison sets expectations rather than ruling the spare out.

Diameter and width comparison works on the numbers, not on how the tire looks on the vehicle. Two tires with the same code have the same nominal size. A worn road tire sits slightly smaller than a new one of the same code.

Check the wheel, hub and brake clearance

Spare tire size matching includes the wheel, because the tire must sit on a rim with the right bolt pattern and center bore. Count the wheel studs or bolt holes on the vehicle hub and match them to the spare wheel. The center bore must sit flush on the hub face.

Brake clearance matters on vehicles with large brake calipers, and a small temporary spare may not clear them. Test fit the spare at low speed in a safe place before you drive on it. A spare that rubs the caliper or the suspension is not a fit, whatever the sidewall code says.

Roadside spare fit also depends on the offset of the wheel, which sets how far the tire sits from the hub. A wheel with the wrong offset pushes the tire into the fender or out past it. Check the fit with the vehicle raised and the wheel turned by hand.

Handle a guest vehicle spare with care

A guest vehicle spare size check calls for the same steps, with extra care because you did not choose the tire. Read the sidewall code and measure the diameter before you fit the spare to a vehicle you do not own. Confirm the wheel bolts match the hub and that the spare clears the brakes.

The spare in a guest vehicle may be original equipment or a replacement of a different size. Check the tire pressure and the condition of the rubber as well as the size. A cracked or flat spare is not usable even when its size matches.

Record the spare size and the road tire size so the owner knows what was fitted. Tell the owner about any size difference and any limit marked on the spare. A trained technician should confirm the fit when the vehicle has modified brakes or suspension.

Use the right limits for a temporary spare

A temporary spare is a short-trip tire, and its speed rating and load index set the limit for use. The tire is narrower and lighter than a road tire, which is why it saves space in the trunk. Drive to a tire shop and have the road tire repaired or replaced.

Temporary spare dimensions differ from the road tire, and the vehicle may pull or handle differently with the spare fitted. Keep speed low and avoid hard braking or cornering on the spare. Check the pressure of the spare before you fit it, because a stored tire loses air over time.

A full size spare can match the road tires exactly, and then the size check becomes a direct comparison. Confirm the full size spare still matches the current road tires after any change of tire brand or size. A mismatch on a driven axle affects the differential on some vehicles.

Spare Tire Size Questions

How do I check spare tire size without a sidewall code?

Measure the spare diameter with a tape across the center of the tread and measure the width across the tread face. Compare those two figures to the decoded size of the road tires. Take the reading at the tread and repeat it at a second point to confirm.

Does the spare tire size need to match the road tires?

A temporary spare does not match the road tires in size, and it is built to run at reduced speed for a short distance. A full size spare should match the road tire size and the wheel fitment. Check the difference in diameter before you drive on any spare.

What is a roadside spare tire size match?

A roadside spare tire size match means the spare fits the wheel studs, clears the brakes and sits within the fender when mounted. The size code and the measured diameter tell you whether the tire is close enough to the road tires for a short trip. Test fit the spare before you rely on it.

How do I read the load index and speed rating on a spare?

The load index is a number after the size code, and the speed rating is a letter beside it. These figures state the load and speed the spare can handle. A temporary spare carries lower figures than the road tires, so keep within them.

Can I use a different size spare on a guest vehicle?

A different size spare is acceptable only as a temporary tire within its marked limits and only if it fits the wheel and clears the brakes. Confirm the stud pattern, center bore and offset before mounting it. Ask a trained technician to check the fit when the vehicle is not your own.

Read next

Latest articles