# How to Change Tire Size in FORScan

Learn how FORScan changes tire size in Ford modules, what the circumference setting does, and how to plan the job safely before you touch any configuration.

FORScan can change the tire size a Ford vehicle's modules use, and it does so by writing a new tire circumference or diameter value into the vehicle configuration. The tool edits software settings, not the tires themselves, so the result is a corrected speedometer and shift logic that matches the tires you installed. Plan the values before you connect, because an incorrect entry affects how the vehicle reads its own speed. 

- FORScan edits the tire size value stored in Ford modules, which corrects speedometer and related readings.
- Tire circumference is the figure the vehicle uses, and it comes from the real mounted tire, not the sidewall size alone.
- A modified vehicle profile in FORScan saves the original values so you can return to stock.
- FORScan Lite covers monitoring on a phone, but writing configuration changes needs the full Windows software.
- Mismatched or wrong values can cause shift and speed errors, so verify the entry before you drive.
 

## What FORScan does with tire size 

FORScan is a Ford vehicle scan tool that reads and writes module configuration over an OBD-II connection. Changing tire size in FORScan means editing the stored value that tells the modules how large the tires are. The software sends that value to the module that holds the setting. 

The tool does not measure your tires or adjust the suspension. FORScan only changes the number the vehicle uses for calculations. Speedometer calibration and speedometer correction follow from that number, so the entry has to describe the tires actually on the vehicle. 

A tire size change alters how the vehicle reports speed and how the transmission decides when to shift. Modules that compare wheel speed against expected values react to the new figure. Treat the edit as a configuration change, not a cosmetic tweak. 

## Can you change tire size with FORScan 

Yes, you can change tire size with FORScan on Ford vehicles whose modules expose a tire size setting. The option appears in the module configuration menu when the vehicle supports it. Not every Ford model or model year offers an editable value, so confirm the setting exists before planning the job. 

FORScan tire size editing depends on the module and the license level of the software. The free version reads data, while writing configuration needs an extended license. Check that your adapter supports writing before you start, since some adapters only read. 

You cannot change tire size with FORScan Lite, because the phone app is built for monitoring and reading. Full configuration writing happens in the Windows version of FORScan. Plan the change on a laptop with a suitable adapter. 

## Find the tire circumference the vehicle needs 

Tire circumference is the distance the tire travels in one full revolution, and it is the figure that drives the setting. Measure it with the tire mounted and inflated to the pressure you run. A tape measure around the tread center gives a working value. 

The sidewall size is a starting point, not the final number. Load, inflation and tread wear change the rolling distance. A tire circumference calculator for FORScan converts a measured diameter into the value the module expects, and it keeps the arithmetic consistent. 

Record the measured circumference and the sidewall size together. If the module asks for diameter instead of circumference, divide the circumference by pi to get the diameter. Keep both figures in your notes for the next step. 

## Back up the vehicle profile before editing 

A vehicle profile in FORScan stores the module data it reads from the vehicle, and it gives you a way back. Create or update the profile with the current tires fitted before any edit. The profile then holds the original tire size setting. 

Save the profile to a known folder and note which module holds the tire size value. The module configuration screen shows the address and the current entry. A written record of the original value protects you if the new entry causes trouble. 

If the edit goes wrong, the saved profile lets you restore the previous setting. Restoration still needs the same adapter and software that made the change. Confirm the profile loads correctly before you write anything. 

## Steps to set tire size in FORScan 

The job follows a fixed order: connect, read, edit and verify. Work with the ignition on and the engine off unless the software instructs otherwise. Keep the laptop charged and the adapter firmly seated through the whole session. 

Open the module configuration for the module that holds the tire size value. Enter the new circumference or diameter in the unit the screen shows, then write the change. Read the module again after writing to confirm the value took. 

A test drive at low speed shows whether the speedometer reads sensibly against a known reference. Stop and restore the original value if the reading is far off. Repeat the measurement and the entry before trying again. 

- Connect the adapter and confirm FORScan reads the vehicle.
- Save the vehicle profile with the current tires fitted.
- Open the module configuration that holds the tire size.
- Enter the measured circumference in the unit shown.
- Write the value and read the module back to confirm.
- Drive at low speed and compare the speedometer reading.
- Restore the saved profile if the result is wrong.
 

## Why the circumference setting must match 

The circumference setting tells the modules how far the vehicle moves per wheel revolution. A value too large makes the speedometer read low, and a value too small makes it read high. Either error also affects the shift points the transmission uses. 

Speedometer correction is the visible result, and it is also a legal concern in some places because the reading must stay within a tolerance. The tolerance depends on local rules, not on FORScan. Check what applies where you drive before you rely on the corrected reading. 

Gear shifting and torque converter behavior follow the same figure. A large mismatch can make the vehicle hold gears or shift early. Correct the value and the behavior returns to normal, so the setting is worth getting right. 

## Limits of FORScan Lite and other tools 

FORScan Lite runs on a phone and reads live data and fault codes, but it does not write module configuration. Tire size changes belong to the Windows software with an extended license. Keep the phone app for checking readings after the job. 

Some tire size changes sit in a module that also controls other functions. Writing a value there can disturb settings you did not intend to touch. Read the whole module screen before you change one field, and change only the tire size entry. 

When the vehicle does not expose a tire size field, FORScan cannot create one. A dealer-level tool or a specialist may be needed for that vehicle. Stop at that point rather than forcing an entry the module does not support. 

## Plan the change as a timeline 

A tire size change is a short task, and the preparation takes more time than the edit itself. Measure the tires, compute the value and save the profile first. Then the write step is quick and the verification is straightforward. 

Schedule the job when you can test drive right after the write. A quiet road and a known speed reference make the check reliable. Do not combine it with other configuration edits, because a fault then has several possible causes. 

Keep the original value and the new value in one note with the date. The note helps you or a technician later, especially if the tires change again. Revert to stock before selling the vehicle if the new owner fits different tires. 

## Questions about FORScan tire size 

### Can I change tire size with FORScan on an F-150? 

Yes, FORScan can change tire size on an F-150 when the module exposes the setting. The F-150 stores a tire size value that the tool can read and write with the extended license. Confirm the field exists on your model year before you plan the job. 

### Can I change tire size with FORScan Lite? 

No, FORScan Lite does not write tire size configuration. The phone app reads live data and fault codes, but the writing step needs the Windows version of FORScan. Use a laptop and a suitable adapter for the change. 

### What value does FORScan expect, circumference or diameter? 

FORScan expects the unit shown on the module configuration screen, which is often circumference. If the screen asks for diameter, divide the measured circumference by pi. Match the unit on the screen exactly before you write. 

### How do I calculate tire circumference for FORScan? 

Measure around the mounted tire at running pressure, or convert the sidewall size to a diameter and multiply by pi. A tire circumference calculator for FORScan keeps the conversion consistent. Use the mounted measurement when accuracy matters. 

### Does a FORScan tire size change fix my speedometer? 

Yes, a correct tire size entry corrects speedometer readings on a supported Ford vehicle. The module uses the circumference value to compute speed and distance. Verify the result against a known reference after the write. 

### What happens if the tire size value is wrong? 

A [wrong tire size](/articles/symptoms-of-a-wrong-tire-size/) value makes the speedometer read high or low and can disturb shift points. The vehicle still drives, but the readings are off. Restore the saved profile and recheck the measurement before trying again.
