# Hoosier TrackAttack Tire Sizes and Fitment

Read Hoosier TrackAttack tire sizes by section width, overall diameter and approved rim width, then work out fitment before a wheel goes on the car.

Hoosier TrackAttack tire sizes are given by section width and overall diameter, and those two numbers decide whether the tire fits your wheel and your car. Fitment compares the approved rim width with your wheel width and checks the overall diameter against the space around the tire. Measure before you buy, because a TrackAttack is a track-oriented tire that leaves little room for error. 

- Size is read as a section width and an overall diameter, not as a metric sidewall ratio.
- The approved rim width on the spec sheet is the guide for wheel fitment.
- Overall diameter changes clearance, gearing and speedometer reading.
- Section width needs room to clear the strut, spring and inner fender.
- Measure your wheel width and the space in the wheel well before ordering.
 

## How Hoosier TrackAttack sizes are written 

A Hoosier TrackAttack size is written as a section width followed by an overall diameter, both in inches. The first number describes how wide the tire body is when it sits on its measuring rim. The second number describes how tall the mounted tire stands from the ground to the top of the tread. 

The format differs from a metric passenger tire size, which uses a width, a sidewall ratio and a wheel diameter. A TrackAttack size carries no sidewall ratio, so you cannot treat the numbers like a 225/45R17. Read each number as a physical dimension of the tire itself. 

Hoosier lists the sizes for this tire line in its own fitment data, and an authorized dealer can confirm what is available at the time you order. The general size reading stays the same across the line, whatever sizes are offered. Write down the full size exactly as it appears before you compare it with your wheel. 

## Section width and overall diameter explained 

Section width is the widest point of the tire body, measured across the sidewalls on the approved measuring rim. This number tells you how much lateral space the tire needs inside the wheel well. A tire that is too wide can rub the strut, the spring or the inner fender. 

Overall diameter is the height of the mounted tire, measured from the tread to the bead seat on the opposite side. Diameter affects ground clearance, the gap to the fender and the gearing of the car. A taller tire lowers engine speed at a given road speed and can touch the fender or liner. 

Section width and overall diameter work as a pair, and you should check both against the car. A size that clears on width may still be too tall, and a size that clears on height may be too wide. Measure the space you have at full steering lock and at full suspension travel. 

## Check approval with the rim width 

Approved rim width is the wheel width range the tire maker states for a given size, and fitment depends on it. Every TrackAttack size has a measuring rim and a range of wheel widths that support the intended tread shape. Mounting a tire on a rim outside that range changes the contact patch and the sidewall shape. 

A wheel narrower than the approved range pulls the sidewalls inward and rounds the tread. A wheel wider than the range stretches the sidewalls and flattens the tread. Both cases change how the tire behaves at the limit, which matters on a track-oriented tire like the TrackAttack. 

Read the wheel width from the inside of the rim, where it is stamped, rather than from the tire that is on it now. Confirm the approved rim width for the exact size with the tire maker or dealer data. Fitment is a check against the stated range, not a guess from how the old tire looked. 

## Measure the space the tire needs 

Wheel well clearance decides whether a TrackAttack size fits a given car, and the check starts at the strut and inner fender. Turn the steering to full lock and look at the gap between the tire and the nearest suspension part. Measure the gap at the top of the tire to the fender lip as the suspension compresses. 

Brake caliper clearance is a separate check, because the wheel spokes and barrel must clear the caliper. Tire width adds to the outer edge, and a wider section can move the sidewall closer to the fender lip. Ride height and alignment settings change the space you measured, so note them on the car. 

A trained technician or alignment shop can measure clearance with the car on a lift and the suspension loaded. Ask for the measurement at full travel on both sides, since the two sides are rarely identical. Stop and get advice if any gap looks tight, because a rubbing tire can damage the fender or fail. 

## How a size change alters the car 

Changing from the stock size to a TrackAttack size alters gearing, speedometer reading and clearance at the same time. A larger overall diameter raises the car and reduces engine speed for a given road speed. A smaller diameter does the opposite and brings the tire closer to the ground. 

Section width changes the tire footprint and the steering feel, and a wider tire asks more of the wheel width. Keep the approved rim width in the range so the sidewall can do its job. Note the new size and its diameter in your records so you can compare later. 

Speedometer error follows the diameter change, and an electronic correction may be needed on some cars. Gearing changes matter most on track, where exit speed from a corner depends on the tire height. Plan the size around the use of the car, then check that the wheel and the wheel well accept it. 

## Steps to confirm fitment before ordering 

Fitment is confirmed by matching the size data to the wheel and the car, one check at a time. Start with the wheel width, then the tire dimensions, then the physical clearance on the car. Order only after every check passes on the exact car and wheel you will use. 

Write down each result so a technician can review it with you. The size on the tire and the width on the wheel must both come from the parts themselves, not from a listing. A dealer who sells the TrackAttack can confirm the size data for the tire you receive. 

Mounting and balancing a track-oriented tire calls for proper equipment and trained hands. Have a qualified shop mount the tire and check clearance before the car is driven hard. If any measurement is uncertain, stop and get a professional opinion before the wheels go on the car. 

- Read the wheel width from the stamp inside the rim.
- Confirm the approved rim width for the exact TrackAttack size.
- Compare overall diameter with the stock tire height.
- Measure strut and fender clearance at full steering lock.
- Check brake caliper clearance at the wheel spokes.
- Have a qualified shop mount the tire and recheck clearance.
 

## Mistakes that spoil a TrackAttack fit 

A fitment error with a TrackAttack tire tends to show up at the first hard corner or the first bump. Trusting the old tire as a size reference is one mistake, because it may not match the stock size or the wheel. Guessing the wheel width from the tire is another, since the stamp inside the rim is the reliable source. 

Reading a TrackAttack size like a metric size is a frequent slip, because there is no sidewall ratio to divide. Ignoring the approved rim width leads to a stretched or pinched sidewall. Measuring clearance with the car on the ground and the wheels straight misses the tight spots at full lock and full travel. 

Rushing the mount and skipping a clearance check after the wheels go on leaves rubbing unnoticed. A rubbing tire can cut into a fender liner or a suspension part. Take the time to check each corner, and let a trained technician handle any work that touches the suspension or brakes. 

## Hoosier TrackAttack fitment questions 

### What Hoosier TrackAttack tire sizes are available? 

Hoosier TrackAttack tire sizes are listed by section width and overall diameter in inches, and the current list comes from the tire maker or an authorized dealer. The line does not use metric sidewall ratios, so each size reads as two physical dimensions. Ask the dealer for the size sheet that applies when you order. 

### How do I read a Hoosier TrackAttack tire size? 

A Hoosier TrackAttack tire size reads as a section width followed by an overall diameter, both in inches. The first number is the widest point of the tire body and the second is the mounted tire height. There is no sidewall ratio in this format, so do not read it like a 225/45R17. 

### What rim width fits a Hoosier TrackAttack? 

The approved rim width for a Hoosier TrackAttack depends on the exact size, and the tire maker states a range rather than a single wheel width. Match your wheel width, stamped inside the rim, to that range before mounting. A wheel outside the range changes the tread shape and the sidewall behavior. 

### Will a wider TrackAttack tire fit my car? 

A wider TrackAttack tire fits only if the section width clears the strut, spring and inner fender at full steering lock and full suspension travel. Check the approved rim width for your wheel as well, because a wide tire needs a wheel within its stated range. Measure the actual gaps on your car with the suspension loaded before you order. 

### Does a larger overall diameter change my speedometer? 

A larger overall diameter raises the mounted tire height and changes the speedometer reading, because the car travels farther per wheel revolution. Gearing shifts in the same way, which matters on track. Note the diameter difference from the stock tire and ask about correction if the reading matters to you.
