# Dually Tire Width on Dual Rear Wheels

Learn how dually tire width and dual rear wheel spacing work. Read how to read sidewall codes, measure, and check clearance.

Dually tire width is the tire section width in millimeters, taken from the size code on the sidewall. On dual rear wheels, the mounted width also depends on rim width, pressure, and load. Proper dual rear wheel tire spacing keeps the inner and outer sidewalls apart for cooling and clearance. 

- Dually tire width is the section width in millimeters from the [tire size code](/articles/tire-size-markings-width-aspect-ratio-construction-rim-size-material-44540/).
- Mounted width changes with rim width, pressure, and load.
- [Dual rear wheel spacing](/articles/minimum-dual-spacing-vs-centerline-vs-sidewall-clearance-material-46672/) is the gap between inner and outer sidewalls in the pair.
- Check back-to-back dual tire clearance to avoid heat and rub.
 

## What dually tire width means 

Dually tire width is the section width molded into the size code. The first number, in millimeters, measures sidewall to sidewall unmounted. LT235/80R17 is about 235 mm wide; LT215/85R16 is about 215 mm wide. 

That number is a starting point, not the final mounted width. The tire bulges or stiffens based on rim width and pressure. Wider wheels make the mounted width slightly wider. 

Overall diameter also affects how the tire sits in the wheel well. A taller tire can move the sidewall closer to the fender or liner. Check both width and diameter when planning fitment. 

## How to read the tire size code 

A common code like LT235/80R17 tells the key dimensions. LT means light truck construction. The 235 is section width in millimeters. 

The 80 is aspect ratio, sidewall height as a percent of section width. R means radial, and 17 is rim diameter in inches. Together they set width, height, and fit. 

Load range and maximum inflation also influence mounted width. Higher pressure under load can make the tread patch wider. Use the vehicle placard for baseline pressure. 

## Dual rear wheel tire spacing explained 

Dual rear wheel tire spacing is the gap between the inner sidewall of the outer tire and the outer sidewall of the inner tire. It is not a fixed spec; it follows axle width, wheel offset, and rim width. 

Adequate spacing allows airflow between tires to control heat. It also keeps debris from being pinched between sidewalls. Tight spacing can speed wear and damage sidewalls. 

Wheel offset and hub centric rings change where the tires sit. Two wheels with different offsets can change the gap even with the same tire size. Keep the pair matched. 

## Back-to-back dual tire clearance 

Back-to-back dual tire clearance is the space between the two inner sidewalls that face each other. It is set by wheel design and axle register. Some dual wheels have a deep well; others are flatter. 

Good clearance prevents the inner sidewalls from touching under load. Contact can trap heat and cause rapid wear. A small, even gap is the goal. 

Check clearance with the vehicle at curb weight and again near rated load. Suspension compression moves the tires inward. Re-check after any wheel change. 

## Dually tire width calculation steps 

Start with the section width from the size code in millimeters. Convert to inches if needed by multiplying by 0.03937. This is the baseline mounted width. 

Adjust for rim width because a tire grows or shrinks slightly on different rims. Manufacturer charts show how width changes with approved rims. 

Add the effect of pressure and load, which change the tread footprint. Then confirm the final mounted width with a straightedge or tape on your actual setup. 

## Measuring width and spacing on the truck 

Park on level ground and set tire pressures to normal operating values. Measure section width across the mounted tread and sidewalls. 

For dual spacing, measure the gap between the inner sidewall of the outer tire and the outer sidewall of the inner tire. Note both sides for evenness. 

Also measure to the fender, liner, and frame at curb height and with the suspension compressed. Record the smallest gap as your limiting clearance. 

## Rim width, sidewall, and overall diameter 

Rim width controls how the sidewall sits. A tire on a narrow rim looks taller and narrower; on a wide rim it looks slightly wider and flatter. 

Sidewall size, shown by the aspect ratio, affects overall diameter. Taller sidewalls increase diameter and can move the tread outward. 

Overall diameter changes speedometer error and wheel well clearance. Match diameter closely when changing sizes on dual rear wheels. 

## Fitment checks before you buy 

Confirm the tire size matches the wheel width range on the tire data sheet. Do not mount outside approved rims. 

Verify dual rear wheel spacing and back-to-back dual tire clearance with your exact wheels. Keep the inner and outer wheels identical. 

Check load range and inflation to meet the vehicle’s gross axle weight. Proper pressure helps width, wear, and heat control. 

## Dually tire width and spacing questions 

### How wide are dually tires? 

Dually tire width is the section width in millimeters from sidewall to sidewall. A common LT235/80R17 is about 235 mm wide, while LT215/85R16 is about 215 mm. The mounted width also depends on rim width and pressure. 

### What is dual rear wheel tire spacing? 

Dual rear wheel tire spacing is the gap between the inner sidewall of the outer tire and the outer sidewall of the inner tire. It comes from axle hub width, wheel offset, and rim width. Adequate spacing prevents heat buildup and rub. 

### How do I calculate dually tire width from the size code? 

Start with the section width in millimeters from the tire size code. Multiply by 0.03937 to get inches if needed. Then add the effect of rim width, since a wider wheel makes the mounted width slightly wider. 

### What is dual rear tire clearance and why does it matter? 

Dual rear tire clearance is the space around both sidewalls in the dual pair and near the fender and frame. It matters because tight clearance can cause heat, wear, and debris trapping. Aim for even, unobstructed gaps. 

### Do I need a dually tire size calculator? 

A calculator helps estimate overall diameter and mounted width from size, rim width, and pressure. It is useful for checking fit, but confirm with a tape measure on your actual wheels and tires.
