# DIY Wheel Chocks for Motorcycles and Trailers

How to build a DIY motorcycle or trailer wheel chock that fits your wheel width and holds against roll, plus how to use it safely for sidewall checks.

A DIY wheel chock is a shaped block or cradle that holds a wheel from rolling while a motorcycle or trailer sits still. You build it to match the wheel width and the load, fix it to a non-slip base, and add tie-down points for transport. The same chock gives you a stable way to inspect a tire sidewall. 

- Match the cradle to the wheel width so the tire sits in the chock without pinching.
- A non-slip base and a firm fixing keep the chock from sliding under load.
- A motorcycle chock on a trailer needs tie-downs as well as the cradle.
- Spread the load over a wide plank or frame rather than a thin board.
- Check the chock and its fasteners before every use.
 

## What a DIY wheel chock has to do 

A DIY wheel chock does one job: it stops a wheel from rolling along its own direction of travel. The chock takes the load in shear and compression, so the material and the joints must carry the weight of the machine. A simple wedge works for a trailer wheel, while a motorcycle needs a cradle that also holds the front wheel upright. 

Roll is not the only force to consider. Sideways push from a leaning bike, wind on a trailer, or a hand on the bars all try to tip or slide the chock. The base needs grip, and the chock needs a shape that resists a sideways shove as well as a forward roll. 

The chock also sets the height of the machine while you work. A cradle that holds the wheel at its lower arc keeps the tire in contact with a solid surface. That contact matters when you read tire markings or check a sidewall for damage. 

- Stop forward and backward roll of the wheel.
- Resist sideways shove from a leaning bike or wind.
- Hold the wheel at a stable height for inspection.
- Keep its base from sliding on the floor or trailer deck.
 

## Match the cradle to the wheel width 

Wheel width fit decides whether a DIY motorcycle chock holds or fights you. The cradle should touch both sides of the tire near the lower third, with a small clearance so the tire drops in without force. Measure the tire width at its widest point of the tread, not at the rim. 

A narrow cradle pinches a wide tire and makes it climb out under load. A cradle that is too wide lets the wheel rock side to side, and the bike will lean against the tie-downs. Build the side plates so you can move them or add a shim when you change tires. 

For a trailer wheel chock, the axle-to-axle spacing of a pair of wheels sets how the chocks sit together. Keep each chock centered under its wheel so the trailer frame takes the load evenly. Wide trailer tires need a wider trough than a motorcycle tire of the same diameter. 
| Wheel type | Cradle shape | Key fit check | 
| Motorcycle front wheel | V or U trough with side plates | Tire contacts both plates near the lower third | 
| Trailer wheel | Wedge or curved trough | Tire sits centered over the axle line | 
| Scooter or small wheel | Shallow U trough | Tire drops in without force |  

## Build steps for a motorcycle chock 

A DIY motorcycle chock for a trailer or a garage floor starts with a base wider than the cradle so it cannot tip. Cut a base board or weld a frame, then fix two side plates at an angle to form the trough. The front stop plate takes the forward roll and must reach at least halfway up the tire. 

Angle the side plates so the tire settles into the V under its own weight. Fix the plates with bolts or welds that you can inspect, and cover every surface that touches the tire with a smooth strip. A rough edge marks the tire and can cut a sidewall. 

Test the empty chock on the floor, then roll the bike into it with a helper holding the machine upright. The wheel should drop in and stop with light forward pressure. Adjust the plate angles before you fix them for good. 

- Cut a base wider than the cradle and thick enough to resist bending.
- Fix two angled side plates that form a V or U trough.
- Add a front stop plate that reaches at least halfway up the tire.
- Line every tire-contact surface with a smooth strip.
- Bolt or weld the joints where you can inspect them.
- Test with the bike upright and a helper holding it.
 

## Non-slip base and fixing to a trailer 

A non-slip base keeps the chock from walking when a bike rolls in or a trailer bounces. Rubber mat under a floor chock adds grip, while a bolted-down frame suits a trailer deck. A loose chock on a smooth floor is a hazard, because the whole assembly can slide with the machine. 

Fix a trailer wheel chock to the deck through the frame, not through a thin panel. Use bolts with washers wide enough to spread the load, and check that the deck has a solid member under each fixing point. The chock must not rely on the tie-downs to stay in place. 

A removable chock for a trailer needs a positive lock, such as a pin or a latch, so it cannot lift out during travel. Test the lock by pulling up on the empty chock. If the chock moves, the load path is not sound. 
| Setting | Base method | What it resists | 
| Garage floor | Rubber mat under a wide base | Sliding and tipping during loading | 
| Trailer deck | Bolted frame through a solid member | Sliding and lifting under travel loads | 
| Temporary use | Mat plus a pin or latch | Movement before the tie-downs are set |  

## Tie-downs work with the chock 

A chock holds the wheel from rolling, and tie-downs hold the rest of the machine. On a trailer, strap the motorcycle so the suspension compresses a little and the front wheel stays in the cradle. The chock and the straps share the job, and neither one does the whole job alone. 

Route each strap so it pulls down and slightly forward into the chock rather than sideways. A strap that pulls the wheel out of the trough makes the chock useless. Pad the contact points on the bars or frame so the strap does not rub a painted or soft part. 

A motorcycle stand under the swingarm or sump can lift the rear wheel for a check, but it does not replace a chock on a trailer. Use a stand only on firm, level ground, and keep the bike strapped while it is raised. 

- Pull straps down and slightly forward into the cradle.
- Compress the suspension a little, not fully.
- Pad every strap contact point on bars or frame.
- Keep the bike strapped whenever a stand lifts a wheel.
 

## Using the chock for sidewall inspection 

A wheel held in a chock is a stable place to [read a tire sidewall](/articles/tire-sidewall-symbols-dates-approval-markings-material-44526/) and look for damage. The sidewall carries the size code, the load index and the date code, and a clean reading needs the tire still. With the wheel chocked and tied down, you can trace the whole sidewall by turning the wheel in steps. 

Look for bulges, cuts, exposed cords and cracks between the tread and the sidewall. A bulge in the sidewall means the internal structure is damaged, and the tire should come off the road. Mark anything you find on the tire so a tire specialist can locate it. 

Do not crawl under a machine that is held only by a chock or a jack. Use axle stands on firm ground for any work beneath a raised vehicle. Sidewall reading itself needs only the wheel off the ground or standing on a level surface. 

- Turn the wheel in steps to read the full sidewall.
- Note the size code, load index and date code.
- Check for bulges, cuts, exposed cords and cracks.
- Mark any damage before you take the tire for inspection.
- Use axle stands for any work under a raised machine.
 

## Checks before each use 

A DIY chock is only as good as its last inspection, so check it before every loading or inspection session. Look at the joints for cracks, loose bolts or bent plates, and replace any part that has deformed. A chock that has taken a hard hit should come out of service until you check it. 

Check the non-slip base for grit, oil or wear that reduces grip. Clean the floor or deck under the chock and confirm the fixing points are tight. A chock that slides a little when empty will slide more with a machine on it. 

Recheck wheel width fit after a tire change, because a new tire can be wider or narrower than the old one. If the tire rocks in the cradle or pinches, adjust the side plates before you load the bike. Keep the chock dry and store it where its base will not warp. 

## Limits of a home-built chock 

A home-built chock suits a still machine, a trailer deck and sidewall checks, and its limits follow the materials you use. Wood can crack along the grain under a heavy load, and thin steel can bend at a weld. Match the build to the weight of the machine and the forces you expect. 

A chock does not replace a rated stand, a lift or a trailer tie-down system. Where a machine is heavy, a commercial rated chock or a trained fitter takes over the load path. If you are unsure about a weld or a fixing, have a qualified metalworker check it. 

A trailer carrying a motorcycle should be loaded and strapped to a recognized standard, and that is a job for a trained specialist. Use a home-built chock as an aid inside that system, and never as the only thing holding a machine. 

## Questions about DIY motorcycle and trailer chocks 

### Can I build a DIY motorcycle chock for a trailer? 

Yes, a DIY motorcycle chock for a trailer can work when the cradle matches the wheel width and the frame is bolted to a solid deck member. The chock must be a partner to the tie-downs, not a replacement for them. Test the empty chock and the loaded bike before travel, then inspect the fixings. 

### How do DIY wheel chocks for motorcycles differ from a trailer wheel chock? 

DIY wheel chocks for motorcycles use a V or U cradle with side plates that hold a single front wheel upright. A trailer wheel chock often uses a wedge or curved trough under each trailer wheel and takes load along the axle line. Both need a non-slip base, but the motorcycle version also needs a front stop plate. 

### What wheel width fit does a motorcycle chock need? 

A motorcycle wheel chock needs side plates that touch the tire near its lower third, with a small clearance for the tire to drop in. Measure the tire tread width, not the rim width, and leave room to adjust the plates after a tire change. A pinching cradle or a loose one both make the bike unstable. 

### Is a chock enough to hold a bike while I check the sidewall? 

No, a chock alone is not enough for every sidewall check, though it makes the wheel stable. Keep the machine tied down or on firm level ground, and use axle stands for any work under a raised vehicle. Read the sidewall by turning the wheel in steps while the machine stays supported. 

### Do I still need tie-downs if the bike sits in a chock? 

Yes, tie-downs are still needed because a chock only stops the wheel from rolling. Route each strap down and slightly forward into the cradle, and compress the suspension a little. The straps and the chock share the load, and neither one holds the machine by itself. 

### What material holds up for a home-built wheel chock? 

Steel or thick structural plywood can hold up for a home-built wheel chock when the joints and base carry the load. Wood can split along the grain and thin steel can bend at a weld, so match the thickness to the weight of the machine. Have a qualified metalworker check any weld you are unsure about.
