Converting Bias Ply Tire Sizes to Radial Equivalents
How to read a bias ply tire size, work out its overall diameter, and pick a radial equivalent size that keeps fitment and speedometer accuracy close.
Contents
- What a bias ply size tells you
- Find the overall diameter of the bias tire
- Read a radial size in the same terms
- Use a bias to radial equivalent chart
- Check width, rim and wheel type
- Keep load index and speed rating in range
- Confirm speedometer accuracy and fit
- Bias ply to radial conversion questions
- What is a bias ply tire size conversion?
- How do I convert a bias ply size to radial with a chart?
- What is the radial tire equivalent for a 7.75-15 bias ply?
- Does a radial equivalent change the speedometer reading?
- What else matters besides overall diameter match?
- Can I fit radial tires on vintage wheels?
Converting a bias ply tire size to a radial equivalent means matching overall diameter first, then width and rim diameter. A bias ply size such as 7.75-15 has no direct radial twin, so you calculate the height from the sidewall aspect and compare it with radial sizes on the same wheel. The closest radial equivalent is the one whose overall diameter and section width sit near the original.
- Match overall diameter before anything else, because ride height, clearance and speedometer accuracy follow the tire height.
- Work out a bias ply diameter by adding twice the sidewall height to the rim diameter.
- A radial size needs a load index and speed rating at least equal to the original tire.
- Rim width and wheel type must suit the radial tire you choose, so check the wheel before buying.
- A conversion table gives a starting point, and a dry test fit confirms the choice.
What a bias ply size tells you
A bias ply tire size is written as a section width in inches followed by the rim diameter, such as 7.75-15. The first number is the nominal width across the inflated tire, and the second is the wheel diameter it mounts on. Bias ply sizes carry no aspect ratio, because the body plies run at an angle and set the sidewall height by construction.
Older bias ply markings may add a letter code or a load range instead of a load index. A letter such as F or G describes the ply rating and the load the casing can carry. The load index on a radial tire does the same job in numbers, so the two systems are compared by the load each tire can support.
Bias ply tires have a taller, rounder sidewall profile than radials of the same width. That shape changes how the tire sits on the rim and how much it grows at speed. Reading the size correctly is the first step before any conversion table or calculator can help.
Find the overall diameter of the bias tire
Overall diameter of a bias ply tire is the rim diameter plus twice the sidewall height. For older sizes the sidewall height is taken as the full section width in inches, so the diameter equals the width times two plus the rim diameter. A 7.75-15 tire therefore works out to about 30.5 inches in diameter.
This rule of thumb fits the older inch sizes that assumed a 100 percent aspect ratio. Some bias ply sizes, especially light truck and motorcycle markings, state the aspect ratio or use a different code. Where the sidewall gives an aspect figure, use it in the same diameter formula instead of the default.
Measured diameter differs slightly from the calculated figure because of tread depth, inflation and rim width. Treat the number as a target for the radial equivalent, not a precise dimension. Overall diameter match is what keeps the vehicle sitting at the same height.
Read a radial size in the same terms
A radial tire size is written as section width in millimeters, aspect ratio as a percentage, and rim diameter in inches, such as 225/70R15. The aspect ratio is the sidewall height as a percentage of the section width. That figure lets you calculate the radial diameter in the same way as the bias tire.
Convert the metric width to inches by dividing by 25.4, then multiply by the aspect ratio to get sidewall height. Double the sidewall height and add the rim diameter to reach overall diameter. The radial equivalent size is the one whose result lands close to the bias figure.
Radial sizes also carry a load index and a speed rating after the size. Both describe the tire's capacity and its maximum speed, and both matter for fitment. A radial that matches diameter but falls short on load index is not an equivalent.
Use a bias to radial equivalent chart
A bias ply to radial equivalent chart pairs legacy inch sizes with radial sizes that share a close overall diameter. The chart is a shortcut for the diameter arithmetic and a starting point for fitment. Charts vary in which radial size they list, so compare the numbers rather than trusting a single line.
Charts often list a narrow and a wide radial option for the same bias size. The narrow option keeps the section width close to the original, while the wider one fills the wheel arch more. Bias to radial fitment depends on clearance, so check both against the vehicle before deciding.
Where a chart offers no close match, the diameter calculation decides. A radial within a small fraction of an inch of the bias diameter is a reasonable equivalent radial size. The conversion table is guidance, and the physical check confirms it.
| Bias ply size | Calculated diameter | Radial sizes to compare |
|---|---|---|
| 6.00-15 | 27.0 in | 195/65R15, 205/60R15 |
| 7.75-15 | 30.5 in | 215/70R15, 225/65R15 |
| 8.25-16 | 32.5 in | 235/75R16, 245/70R16 |
| 9.00-16 | 34.0 in | 255/75R16, 265/70R16 |
Check width, rim and wheel type
Overall diameter match alone does not make a radial equivalent fit. Section width must clear the suspension, steering and bodywork through the full range of travel. A radial wider than the bias original can rub where the old tire had room.
Rim width must suit the radial tire, and a narrow wheel pinches a wide radial into a poor shape. Wheel type matters as well, because some older wheels are not rated for radial tire loads. A trained tire specialist should confirm that a vintage wheel accepts a radial before mounting.
Bead seat and rim profile differ between old and new wheels, and a mismatch can affect how the tire seals. Checking rim width and wheel condition belongs to the fitment decision, not to the size arithmetic.
Keep load index and speed rating in range
A radial equivalent must carry at least the load the original bias tire was rated for. Bias ply load ranges convert to radial load indexes, and the vehicle's axle loads set the minimum. Fitting a radial with a lower load index reduces the tire's capacity.
Speed rating describes the maximum sustained speed the tire is built for. The radial you choose should meet or exceed the rating the vehicle needs. A higher speed rating does not harm fitment but may come with a different sidewall construction.
Load index and speed rating sit in the size string, so read the whole marking rather than only the dimensions. Two radials of the same size can differ in capacity. The equivalent is the one that meets both figures.
Confirm speedometer accuracy and fit
Speedometer accuracy depends on the tire's rolling circumference, which follows overall diameter. A radial equivalent that sits close in diameter keeps the speedometer reading close to before. A taller or shorter tire shifts the reading at every speed.
Rolling circumference changes slightly with inflation, load and tread wear. An exact speedometer match is therefore not possible from size alone. Comparing the calculated diameters gives an estimate of how far the reading will drift.
Before driving on the new tire, check clearance with the vehicle on the ground and the steering at both locks. A dry test fit catches rubbing and rim problems that a conversion chart cannot show. Have a trained specialist mount and balance the tire where the wheel or vehicle needs it.
Bias ply to radial conversion questions
What is a bias ply tire size conversion?
A bias ply tire size conversion matches an older inch size such as 7.75-15 to a radial size with a similar overall diameter. The conversion uses the sidewall height and rim diameter to calculate the height of the bias tire. A radial tire of the same diameter is then the equivalent radial size.
How do I convert a bias ply size to radial with a chart?
A bias ply to radial tire size conversion chart lists legacy sizes next to radial options with a close diameter. Find your bias size on the chart and compare the radial diameters it offers. Confirm the choice with your own diameter calculation and a test fit, because charts vary.
What is the radial tire equivalent for a 7.75-15 bias ply?
A 7.75-15 bias ply calculates to about 30.5 inches in overall diameter. Radial sizes near that diameter, such as 215/70R15 or 225/65R15, are the equivalent radial size to compare. Confirm clearance, rim width and load index before fitting.
Does a radial equivalent change the speedometer reading?
A radial equivalent changes the speedometer reading only when its overall diameter differs from the bias original. Matching the overall diameter keeps speedometer accuracy close to before. Small differences remain because rolling circumference depends on inflation and wear.
What else matters besides overall diameter match?
Load index, speed rating, section width and rim width all matter alongside overall diameter match. A bias to radial fitment also depends on clearance and on whether the wheel is rated for radial tires. Check every figure before mounting a replacement.
Can I fit radial tires on vintage wheels?
Radial tires can fit some vintage wheels, but the wheel must be rated for radial loads and match the tire's bead profile. A trained tire specialist should inspect the wheel before you fit radials. Mounting a radial on an unsuitable wheel can affect safety.