# Converting 30 to 35 Inch Tire Sizes to Metric Equivalents

Learn how to convert 30 to 35 inch tire sizes into metric equivalents, read flotation and metric sidewall markings, and match overall diameter and section width.

Inch sizes like 33x12.50R15 and metric sizes like 285/75R16 describe the same three dimensions: overall diameter, section width and wheel diameter. Converting a 30 to 35 inch tire to a metric equivalent means changing the first number into a metric width code and the aspect ratio into a sidewall percentage. The match is close, not exact, because metric sizes come in fixed steps. 

- An inch flotation size gives overall diameter, section width and wheel diameter in inches, in that order.
- A metric size gives section width in millimeters, sidewall height as a percentage of that width, and wheel diameter in inches.
- To convert, multiply the inch width by 25.4, then work out which aspect ratio brings the sidewall back to the inch diameter.
- Pick the metric size whose calculated overall diameter lands closest to the inch tire, and check the wheel width range.
- A converted size can differ by a small amount in diameter and width, which affects speedometer reading and clearance.
 

## Reading the two tire size formats 

Inch sizes such as 31x10.5R15 are called flotation sizes, and each number has a fixed meaning. The first figure is the overall diameter in inches, the second is the section width in inches, and the number after the R is the wheel diameter. A 35x12.50R20 therefore describes a tire about 35 inches tall, 12.5 inches wide, on a 20 inch wheel. 

A metric tire designation reads like 275/70R18 and works differently. The first number is the section width in millimeters, the second is the aspect ratio, which is the sidewall height as a percentage of the width. The last number is the wheel diameter in inches, so metric sizes mix millimeters and inches in one marking. 

The tire diameter formula ties the two systems together. Overall diameter equals the wheel diameter plus twice the sidewall height, and sidewall height equals section width times aspect ratio divided by 100. Working in one unit at a time keeps an inch to metric tire conversion from going wrong. 

## Converting the width to millimeters 

The section width is the first number to convert in any inch to millimeter conversion. Multiply the inch width by 25.4, because one inch equals 25.4 millimeters. A 12.5 inch section width comes out at 317.5 millimeters, and a 10.5 inch width comes out at 266.7 millimeters. 

Metric sizes are sold in steps, so the exact figure rarely exists. A calculated width of 317.5 millimeters sits between the 305 and 315 metric sizes, and both are candidates for a 35x12.5 tire. Choosing the nearest step is normal practice, and the small difference in width is part of the fitment decision. 

Width affects more than looks, because a wider tire needs a wider wheel and more clearance. Measure the space between the tire and the suspension, the fender and the steering components before committing to the wider of two options. The section width equivalent is a starting number, not a final answer. 

## Finding the aspect ratio that fits 

The aspect ratio is the number that brings a metric size back to the target diameter. Subtract the wheel diameter from the target overall diameter, divide by two to get one sidewall, then divide that sidewall in millimeters by the section width and multiply by 100. The result is the aspect ratio to look for. 

A 35 inch tire on an 18 inch wheel needs a sidewall of 8.5 inches on each side. That sidewall is 215.9 millimeters, and dividing it by a 315 millimeter width gives an aspect ratio near 68.5. The nearest sold metric sizes are 315/70R18 and, for a slightly narrower tire, 305/70R18. 

The same method works across the whole range. A 33 inch tire on a 15 inch wheel needs a 9 inch sidewall, and a 30 inch tire on the same wheel needs 7.5 inches. Run the figures for each target diameter and wheel size rather than reusing a ratio from another combination. 

## A worked conversion table for 30 to 35 inches 

This table shows how a few flotation sizes translate into metric equivalents at a matching wheel diameter. The metric figures are calculated targets, and the closest sold size may differ by a small amount in width or diameter. Treat every entry as a starting point for a fitment check. 

The diameter column matters as much as the width column, because a metric size can sit close in width and still be taller or shorter than intended. Compare the calculated overall diameter in millimeters with the inch diameter multiplied by 25.4. A difference of a few millimeters is normal between an inch size and its metric neighbor. 

Note that 31x10.5R15 is a widely referenced inch size, and its metric match depends on the wheel and the load specification. The flotation size gives the target, while the metric size gives the number that appears on the sidewall of the replacement. 
| Inch size | Target diameter (mm) | Width (mm) | Usable metric size | 
| 30x9.50R15 | 762 | 241 | 235/75R15 | 
| 31x10.50R15 | 787 | 267 | 265/75R15 | 
| 33x12.50R15 | 838 | 318 | 315/70R15 or 305/70R15 | 
| 35x12.50R20 | 889 | 318 | 315/60R20 or 305/60R20 |  

## Handling wheel diameter and load rating 

A metric equivalent must sit on the same wheel diameter as the inch tire it replaces. The R number in each size is the wheel diameter, and mixing a 15 inch tire with an 18 inch wheel is not a conversion but a mismatch. Keep the last number fixed and change only the [width and aspect ratio](/articles/comparing-tire-width-and-aspect-ratio/). 

[Load index and speed rating](/articles/tire-load-index-load-range-speed-ratings-material-44528/) also belong to the metric size and are not part of the inch format. A replacement should meet or exceed the load index the vehicle requires, and that figure is on the tire placard or in the owner's manual. A tire size conversion that ignores load capacity is incomplete. 

The 35x12.50R20 case is a good reminder that wheel diameter drives the ratio. On a 20 inch wheel the sidewall must be shorter than on a 15 inch wheel to reach the same 35 inch overall diameter, so the aspect ratio drops noticeably even though the width stays the same. 

## Checking diameter differences after conversion 

An overall diameter conversion rarely lands exactly on the inch figure. Metric sizes are built in fixed steps, so the closest match can be a few millimeters larger or smaller than 35 inches. Work out the difference as a percentage of the original diameter to see how much the change matters. 

A change in overall diameter affects the speedometer, the odometer and the effective gear ratio. A taller tire turns fewer times over the same distance, so the instrument reading drops relative to true speed. A shorter tire does the opposite, and either direction can be significant on a large change. 

Physical clearance changes with diameter and width together. Check the tire against the inner fender, the upper control arm and the brake lines through the full steering and suspension travel. A tire that clears at rest can still contact a component when the suspension compresses. 

## Why a close match still needs verification 

A calculated metric equivalent is a guide, and the actual tire must be checked against the wheel and the vehicle. Wheel width range is published by the tire maker for each size, and a rim outside that range changes how the sidewall sits. The section width on the sidewall is measured on a specific rim width, not on every rim. 

Mounting, balancing and any clearance work belong with a trained tire specialist. A tire that rubs can damage a brake line or a fender, and an incorrectly seated bead can fail while driving. Ask the specialist to confirm the fitment before the vehicle goes back on the road. 

Tire sizing alone does not cover pressure, alignment or load distribution. Those settings come from the vehicle specification, and a change in tire size may call for a different pressure. Keep the original markings and the new ones together so the specialist can review the whole setup. 

## Questions about inch to metric tire conversion 

### What is the metric tire size equivalent to 35 inches? 

The metric equivalent to a 35 inch tire depends on the wheel diameter and the width. A 35x12.50R20 works out near 315/60R20, while a 35 inch tire on an 18 inch wheel lands near 315/70R18. Both are close matches, and the final choice needs a fitment check. 

### What is the metric size for a 35x12.5 tire? 

A 35x12.5 tire converts to a section width of about 317.5 millimeters, so the nearest metric widths are 305 and 315. The aspect ratio then depends on the wheel diameter. The 35x12.5 marking gives the target, and the metric size gives the sidewall number. 

### What is the equivalent tire size to 31x10.5R15? 

The equivalent tire size to 31x10.5R15 is close to 265/75R15. The width of 10.5 inches converts to about 267 millimeters, and a 75 series sidewall on a 15 inch wheel produces an overall diameter near 31 inches. Confirm the load index before fitting. 

### How do I convert a 33 inch tire size to metric? 

Multiply the inch width by 25.4 to get the metric width, then solve for the aspect ratio using the target diameter and the wheel size. A 33x12.50R15 comes out near 315/70R15 or 305/70R15. The result is a calculated match, so check the sold sizes and the wheel width range. 

### Does a metric equivalent have the same overall diameter as the inch tire? 

No, a metric equivalent is close but rarely identical to the inch diameter. Metric sizes come in fixed steps, so the calculated overall diameter can differ by a small amount. That difference changes the speedometer reading and the clearance, so measure both before fitting. 

### Can I use a metric size on the same wheel as the inch size? 

Yes, as long as the last number in the metric size matches the wheel diameter and the tire maker lists your rim width as acceptable. A 15 inch wheel needs a metric size ending in R15, and a 20 inch wheel needs R20. The wheel width range is the deciding factor.
