# Bolt Pattern for Flange-Mounted Wheels

Learn what a bolt pattern on a wheel mounting flange is, how to read lug hole counts and spacing, and how to match a wheel to a hub flange safely.

A bolt pattern for flange-mounted wheels is the number of lug holes in the wheel mounting face and the diameter of the circle those holes sit on. You read it as two numbers, such as 5 by 114.3, where the first is the lug count and the second is the circle diameter. The pattern on the wheel must match the pattern on the hub flange before the wheel can seat and tighten correctly. 

- A bolt pattern pairs a lug count with the diameter of the circle through the lug holes.
- The wheel pattern and the hub flange pattern must match in both number and spacing.
- Measure across the circle center to center, not across the outside of the holes.
- Even spacing and a flat hub face matter as much as the hole count.
- A pattern adapter changes offset and load path, so treat it with care.
 

## What a bolt pattern actually measures 

A flange bolt pattern describes two things at once: how many lug holes a wheel has and how far apart they sit. The holes are drilled on a circle, and the pattern states the diameter of that circle. Tire technicians write it as a lug count followed by the circle diameter, using millimeters for the diameter on metric vehicles. 

The circle runs through the center of each lug hole, not through the outer edge. Measuring hole edges gives a number that is too large and will not match any published pattern. The lug holes themselves are only one part of the wheel mounting face, which also carries the center bore and the flat surface that presses against the hub. 

Two wheels can share a lug count and still differ in spacing, so the count alone tells you little. A five-lug wheel built on a wider circle will not line up with a five-lug hub flange. Treat the pair of numbers as a single specification that must match as a unit. 

## Reading a bolt pattern chart for flanges 

A bolt pattern chart for flanges lists each pattern by lug count and circle diameter, and it is a lookup aid rather than a measurement. You find your hub flange pattern in the chart, then confirm the wheel you want carries the same entry. Charts are only useful when the numbers on both sides come from the same reliable source. 

Charts group patterns by lug count, so a four-lug section lists several circle diameters in a column. Read across the row for your vehicle to get the full pattern. A chart entry that shows only a lug count is incomplete for fitment purposes and should be checked against a direct measurement. 

Print charts and online tables can carry errors, and vehicle makers revise specifications between model years. Confirm a chart entry against the hub itself before you buy a wheel. The chart answers what a pattern is called, while the hub answers what your vehicle actually has. 
| Lug count | What the number means | How spacing is given | 
| 4 | Four lug holes on the wheel face | Circle diameter through hole centers | 
| 5 | Five lug holes on the wheel face | Circle diameter through hole centers | 
| 6 | Six lug holes on the wheel face | Circle diameter through hole centers | 
| 8 | Eight lug holes on the wheel face | Circle diameter through hole centers |  

## Measuring the hub flange pattern 

Measuring a hub flange pattern starts with cleaning the hub face so the holes and center bore are clear. Count the lug studs or threaded holes on the hub first, since that number fixes the first half of the pattern. Then measure the circle that passes through the centers of those studs or holes. 

Even counts are straightforward because two opposite holes sit on a straight line through the center. Measure from the center of one hole to the center of the hole directly across from it. That distance is the circle diameter, and you can compare it directly with a wheel specification. 

Odd counts have no hole directly opposite, so the measurement needs a different approach. Measure from the center of one hole to the center of the nearest hole, then apply the correction factor for that lug count. A caliper or a dedicated [bolt pattern gauge](/articles/how-to-measure-wheel-bolt-pattern-lug-count-and-bolt-circle-diameter/) gives a cleaner result than a tape measure on a curved surface. If the reading is uncertain, have a trained technician verify it before ordering parts. 

## Matching the wheel to the hub face 

A wheel fits a hub flange only when the bolt pattern, center bore and mounting surface all agree. The lug holes must align with the studs without force, and the wheel should sit flat on the hub face. Any gap between the wheel and the hub face means the wheel is not seated and must not be tightened. 

The center bore carries part of the load and centers the wheel on the hub. A bore that is too small will not fit over the hub, and a bore that is too large needs a centering ring to keep the wheel concentric. Lug holes that are elongated or slotted are not a normal bolt pattern and deserve a close inspection. 

Fastener type matters as much as hole spacing. Some wheels use lug bolts that thread into the hub, and others use studs with nuts. The seat shape on the fastener, whether flat, conical or ball, must match the seat in the wheel. Mixing seat shapes can loosen a wheel or damage the mounting face. 

## Why an offset pattern will not fit 

A pattern with the same lug count but a different circle diameter will not fit, even though the holes look close. Each lug hole sits a small distance from where the stud sits, and that error grows toward the rim. Forcing a wheel onto mismatched studs cross-threads the fasteners and ruins the holes. 

Some wheels carry two patterns drilled into one face so they fit two different hubs. These dual-pattern wheels have extra holes, and only one set aligns with a given hub flange. Check that every stud passes cleanly through its hole, with none resting against the edge. 

A wheel that wobbles on the studs before the nuts are tight is a sign of a pattern mismatch. Stop and identify which number is wrong before continuing. Tightening a mismatched wheel can crack the wheel face and damage the hub, so the safe path is to stop and confirm the pattern. 

## Adapters, spacers and load path 

A bolt pattern adapter converts one pattern to another by bolting to the hub and carrying its own studs. The adapter adds thickness between the hub and the wheel, which changes the offset and pushes the tire outward. Clearance to the fender and suspension must be checked before an adapter goes on. 

Adapters carry the same loads as the original hub, so their material and fastener quality matter. Cheap castings or short studs can fail under cornering loads. A trained specialist should confirm torque values and thread engagement for any adapter installation. 

A plain spacer moves the wheel outward without changing the pattern, and it still relies on the original studs. Longer studs are needed when the spacer is thick enough to leave too few threads for the nut. Neither part fixes a wrong bolt pattern on its own, and neither should be used to force a wheel that does not match. 

## Checking fitment before the wheel goes on 

Fitment checks belong on the bench and on the hub before any fastener is tightened. Lay the wheel against the hub and confirm every stud enters its hole without touching the sides. Spin the wheel by hand once seated to look for runout at the rim edge. 

Torque the fasteners in a star pattern so the wheel pulls down evenly on the hub face. Recheck the torque after the first drive, since seating can settle the joint. Use the torque figure the vehicle maker publishes for that hub flange, not a guess. 

Inspect the hub face for rust, burrs or old balance weights that would hold the wheel off the surface. A clean, flat wheel mounting face lets the wheel seat fully. Any doubt about pattern, bore or fastener seat is a reason to ask a trained technician before driving. 

## Bolt Pattern Questions for Flange Wheels 

### What is a bolt pattern chart for flanges used for? 

A bolt pattern chart for flanges is a lookup table that pairs a lug count with a circle diameter for a given hub. You use it to find the pattern name that matches your hub flange and then confirm the wheel carries the same entry. The chart is a reference, so verify the numbers against the hub itself. 

### How do I measure a bolt pattern on a hub flange? 

Measure the bolt pattern on a hub flange by counting the studs and then measuring the circle through their centers. For an even count, measure across two opposite studs; for an odd count, measure to the nearest stud and apply the correction factor for that count. A caliper or pattern gauge gives a more reliable reading than a tape measure. 

### Can I fit a wheel with the same lug count but a different pattern? 

No, a wheel with the same lug count but a different circle diameter will not fit a hub flange correctly. The studs will not pass cleanly through the lug holes, and forcing the wheel cross-threads the fasteners. Both numbers in the pattern must match before the wheel can seat. 

### Is a bolt pattern adapter safe for changing wheel fitment? 

A bolt pattern adapter can work when it is properly made and installed, but it changes the offset and the load path. The added thickness pushes the wheel outward and can cause clearance problems with the fender or suspension. Have a trained specialist confirm the adapter, stud length and torque before driving on it. 

### What else must match besides the bolt pattern? 

Besides the bolt pattern, the center bore and the fastener seat shape must match the hub and wheel. The center bore centers the wheel, and the seat shape on the nut or bolt must fit the hole in the wheel. The hub face also needs to be flat and clean so the wheel sits fully against it.
