# Back-Calculating Tire Size from Measured Circumference or Diameter

Learn how to back-calculate a tire size from a measured diameter or circumference, convert the result to P-metric or LT codes, and check fitment.

You can back-calculate a tire size by measuring the tire's overall diameter or its circumference and converting that figure into the [width and aspect ratio](/articles/comparing-tire-width-and-aspect-ratio/) codes on the sidewall. The circumference divided by pi gives the diameter, and the diameter minus the rim diameter gives the total sidewall height. Splitting that sidewall height between the two sides yields the aspect ratio that pairs with the width. 

- Divide the measured circumference by pi to get the overall diameter before doing anything else.
- Subtract the rim diameter from the overall diameter to find the combined sidewall height of both sides.
- Halve the sidewall height, then divide by the section width to estimate the aspect ratio.
- Convert millimeters to inches by dividing by 25.4 so measured and coded figures use the same unit.
- A back-calculated size is an estimate, so confirm the sidewall marking or a manufacturer's data before buying.
 

## Measure the tire the right way 

A reliable back-calculation starts with one clean measurement of the mounted tire, taken the same way twice. Wrap a tape around the center of the tread to record the measured tire circumference, or lay a straight edge across the top and measure to the ground for overall height. 

The tire should be inflated to its normal pressure and sitting on level ground with the vehicle's weight on it. A soft or overloaded tire reads smaller than it is, and that error carries straight into the size you calculate. 

Write the number down in millimeters or inches and state which unit you used. Mixing the two units midway through the math is the source of many wrong answers, so convert everything once at the start. 

- Inflate the tire to the pressure you run on the road.
- Measure across the tread centerline, not the shoulder.
- Take the reading twice and keep the consistent one.
- Record the unit next to the number.
 

## Turn circumference into overall diameter 

Dividing the measured tire circumference by pi returns the tire's overall diameter in the same unit. Pi is roughly 3.1416, and that figure is accurate enough for matching a size code. 

The tire diameter formula runs the other way as well, so a known diameter multiplied by pi returns the circumference. Working in both directions helps you check that your measurement is sensible before you trust it. 

Circumference and diameter describe the same circle, so this step adds no new information about the tire. It simply puts your measurement into the form the sidewall codes are built around. 
| Measured value | Operation | Result | 
| Circumference | Divide by 3.1416 | Overall diameter | 
| Overall diameter | Multiply by 3.1416 | Circumference | 
| Diameter in mm | Divide by 25.4 | Diameter in inches |  

## Separate the sidewall from the rim 

The [overall tire diameter](/articles/tire-diameter-chart-in-inches/) includes the wheel, so subtracting the rim diameter leaves the combined sidewall height of both sides. Rim diameter is the number after the R in a size code, such as the 17 in 225/45R17. 

For example, an overall diameter of about 25 inches on a 17-inch rim leaves roughly 8 inches of total sidewall. Halving that gives about 4 inches of sidewall on each side, which is the number the aspect ratio describes. 

The rim diameter must come from the wheel itself, not from the tire, because the two are separate parts. If you are unsure of the rim size, read it off the wheel or the sidewall code rather than guessing. 

## Work back to width and aspect ratio 

Section width and aspect ratio are the two numbers that, with the rim, define a P-metric or LT size. The aspect ratio is the sidewall height divided by the section width, expressed as a percentage, so divide the single-sidewall height by the width to get it. 

An example shows the direction of the math. A single sidewall of about 4 inches on a section width of about 8.9 inches gives an aspect ratio near 45 percent, which points to a size such as 225/45. 

Real tires flex, wear and bulge, so the calculated ratio rarely lands exactly on a listed code. Round to the nearest standard aspect ratio and width step, such as the nearest 5 in the ratio and the nearest 10 in the width. 

## Convert metric and inch figures 

P-metric and LT sizes state the width in millimeters, while diameter and circumference measurements often come out in inches. Metric to inch conversion uses 25.4 millimeters per inch, and applying it once keeps the whole calculation consistent. 

Divide a width in millimeters by 25.4 to get inches, or multiply an inch figure by 25.4 to get millimeters. Do the conversion before comparing your result with a sidewall code, not after. 

A width of 225 mm, for instance, is about 8.9 inches. Keeping that converted figure beside the original helps you spot a misplaced decimal point in the final size. 

## Match the result to a sidewall code 

The tire size designation on the sidewall reads width, aspect ratio, construction and rim diameter in that order. Your calculated width and ratio narrow the field, and the rim diameter you measured confirms the last part of the code. 

A reverse tire size lookup still needs the physical measurements, because a diameter alone can match more than one width and ratio pair. Two tires of the same overall diameter can differ in how much sidewall they carry. 

Compare the calculated size with the sidewall marking or a tire manufacturer's published dimensions before you order. A trained tire technician can confirm fitment on the vehicle and check clearance around the brakes and suspension. 

## Know what limits the accuracy 

A back-calculated size is an estimate because the measurement includes tread wear, inflation and load. A worn tire reads smaller than a new one of the same size, and a loaded tire sits flatter than an unloaded one. 

Different brands also vary slightly in molded dimensions within the same nominal size. That variation is one reason a size lookup by diameter can return a close match rather than an exact one. 

Use the calculation to identify a likely size, then verify it. When the tire feeds a speedometer, a clearance check or a load rating decision, a trained specialist should confirm the choice before the vehicle is used. 

## Questions about tire size back-calculation 

### How do I back calculate tire size from a measurement? 

Back calculating tire size starts with the overall diameter or circumference and works back to the width and aspect ratio. Divide circumference by pi to get the diameter, subtract the rim diameter, halve the remainder, and divide by the width. 

### How do I find tire size from circumference? 

Tire size from circumference comes from dividing the measured circumference by about 3.1416. That gives the overall diameter, which you then break down into sidewall height, aspect ratio and width using the rim diameter. 

### Can I calculate tire size from the measured diameter? 

Yes, you can [calculate tire size](/articles/tire-size-calculator-diameter-comparison-material-44527/) from a measured diameter by subtracting the rim diameter and splitting the rest between the two sidewalls. Dividing one sidewall height by the section width gives the aspect ratio, and the width comes from the measured tread width. 

### Is tire size lookup by diameter reliable? 

Tire size lookup by diameter gives a likely match rather than a certain one, because the same overall diameter can come from different width and aspect ratio pairs. Confirm the result against the sidewall marking or manufacturer's data. 

### Does overall height tell me the exact tire size? 

No, overall height alone does not fix the exact tire size, since it combines rim, sidewall and tread depth. You still need the rim diameter and a width figure to place the size on the sidewall scale. 

### What tools help with a reverse tire size calculation? 

A reverse tire size calculation needs a tape measure, the rim diameter and a calculator for the division and unit conversion. Tire dimension charts from manufacturers also help match your figures to a listed size.
