# Attaching Hubcaps and Wheel Covers with Clips, Tabs or Screws

Learn how to attach hubcaps and wheel covers using clips, tabs or screws, how each fastener holds the cover, and how to seat a cover without retention rings.

You attach a hubcap or wheel cover by pressing its fasteners onto the wheel until the cover seats evenly against the rim. Clips and tabs grip the rim edge, while screws pass through the cover into the wheel or into small brackets. The fastener type decides how you align the cover and how much force you use. 

- Match the fastener type to the wheel before you buy or fit a cover.
- Clips and tabs snap over the rim edge, so you press the cover on straight and evenly.
- Screws hold the cover with threaded fasteners and need the correct holes and torque.
- A cover without retention rings relies on the tabs or screws molded into it to stay put.
- Stop pressing if a cover will not seat, because force can bend the rim lip or crack the plastic.
 

## Identify the fastener your cover uses 

Hubcaps and wheel covers stay on the wheel through clips, tabs or screws, and you should identify which one your cover uses before fitting it. Look at the back of the cover and count the fasteners around its edge. The shape tells you how the cover grips the wheel and how you should align it. 

Wheel cover clips are small springy fingers, often steel, that hook over the rim lip and pull the cover inward. Wheel cover tabs are molded plastic lips that sit on the rim and flex as the cover seats. Hubcap screws are threaded fasteners that pass through holes in the cover. 

A cover may combine fasteners, such as plastic tabs plus a few screws, and that combination changes the fitting order. Read the back of the cover and the wheel face together. Fit the cover to the wheel it was made for, since a cover for a steel wheel has a different grip. 

## Seat a cover that uses clips 

Installing hubcaps with clips means pressing the cover onto the wheel until each clip snaps over the rim lip. Line up the valve stem with its cutout first, because the stem marks the correct clock position. Press with both hands on opposite sides of the cover. 

Work around the cover in stages rather than pushing one spot until it locks. Each clip needs to ride over the rim edge, and an even press keeps the cover square to the wheel. Listen and feel for the clip catching the lip, then press the next area. 

If a clip will not catch, lift the cover off and check that the clip is not bent or missing. A bent clip holds the cover off center and the other clips cannot seat. Replace damaged clips or move to a cover with a different fastener. 

## Press on tabs without retention rings 

Learning how to put on wheel covers with tabs starts with knowing that the tabs are the retention, so the cover needs no separate ring. The molded tabs flex against the rim as the cover goes on and their spring holds it there. Align the valve stem cutout before you push. 

Start at the top and press the cover onto the rim with the heel of your hand. Move around the edge in small steps so each tab folds inward instead of catching flat. The cover should sit flush against the rim when every tab has passed the lip. 

Mounting without retention rings depends on all tabs being present and springy. A cracked or flattened tab lets the cover sit proud and work loose. Check the tabs before fitting and set the cover aside if the plastic is damaged. 

## Fit a cover with screws 

Installing hubcaps with screws means threading each fastener through the cover and into the matching hole or bracket on the wheel. Start every screw by hand so you do not cross the threads. Tighten them in a cross pattern, a little at a time, until the cover sits flat. 

Screw tightness matters more than speed, since an uneven cover can rub or crack at the holes. Stop when the cover contacts the wheel face evenly and the screw feels snug. Never force a screw that binds, because the thread or the plastic hole can strip. 

Check the screws again after the first short drive, when the cover has settled. Loose screws let the cover move and enlarge the holes. Follow the tightness figure the cover maker gives and do not add thread compounds the maker does not list. 

## Match the fastener to the wheel 

The wheel type decides which fastener works, so check the rim before you fit a cover. A steel wheel with a visible rim lip accepts clips and tabs that hook that lip. An alloy wheel may have a different face and needs its own cover type. 

A cover designed for one wheel can look close to right on another and still not grip. The clip spacing, the tab depth and the screw holes all follow the wheel design. Compare the back of the cover with the wheel face before you press anything on. 

Wheel cover fasteners are the interface between cover and rim, and a mismatch shows up as a loose or crooked cover. Ask a tire technician when the wheel and cover do not clearly match. Choosing the right pair avoids damage to both parts. 

## Use a fitting sequence that protects the parts 

A steady sequence protects the rim lip and the cover fasteners during fitting. Clean the rim edge first, because grit between clip and rim prevents the cover from seating. Then line up the valve stem cutout and press the cover on in stages. 

Two hands on opposite sides keep the cover square as the fasteners engage. Rushing one side can bend a clip or crack a tab. Finish by checking that the cover sits flush all the way around. 

A cover that still will not seat after an even press should come off for inspection. Forcing it can bend the rim lip, crack the plastic, or damage a screw thread. A trained technician can check the wheel and cover match if the cause is unclear. 

- Clean the rim edge and the back of the cover before fitting.
- Align the valve stem cutout with the valve stem.
- Press the cover on with two hands, working around the edge.
- Check that clips or tabs have passed the rim lip on every side.
- Start screws by hand, then tighten in a cross pattern.
- Remove and inspect the cover if it will not sit flush.
 

## Inspect and refit after the first drive 

A cover can settle after its first trip, so check the fasteners once the wheel has cooled. Look for a cover that has moved off center or a screw that has backed out. Refit anything that has shifted before it works loose. 

Clips and tabs keep their grip only while they are straight and springy. Bend a clip back into shape only if the maker allows it. Otherwise fit a new clip or a cover with sound fasteners. 

Screws need a quick check of tightness at the same time. A screw that keeps loosening points to a damaged hole or thread. Have a technician look at the wheel if the same fastener will not hold. 

## Hubcap and wheel cover fitting questions 

### How do you install hubcaps with clips? 

Installing hubcaps with clips means pressing the cover onto the wheel so each springy clip hooks over the rim lip. Align the valve stem cutout first, then press with both hands on opposite sides. Work around the cover until every clip has caught and the cover sits flush. 

### Can you install hubcaps without retention rings? 

Yes, a hubcap can mount without retention rings when the cover has molded tabs or screws that grip the rim directly. The tabs or screws act as the retention, so no separate ring is needed. Check that every tab or screw is sound before you press the cover on. 

### How do you install hubcaps with screws? 

Installing hubcaps with screws means passing each screw through the cover into its matching hole or bracket. Start every screw by hand to protect the threads. Tighten them in a cross pattern until the cover sits flat and each screw feels snug. 

### How do you put on wheel covers with tabs? 

You put on wheel covers with tabs by aligning the valve stem cutout and pressing the cover onto the rim in small steps. Each tab folds inward as it passes the rim lip. The cover is seated when it sits flush and every tab has gripped. 

### What should you do if a wheel cover will not seat? 

A wheel cover that will not seat should come off for inspection rather than take more force. Check for a bent clip, a cracked tab, grit on the rim, or a screw that is cross threaded. Forcing the cover can damage the rim lip or the plastic, so a trained technician should check the match if the cause is unclear.
